Page 1 Renault MEGANE Vehicle user manual...
Page 2 Renault cars. Lasting protection and optimum performance for your engine – guaranteed. Whether changing the oil or simply topping up, to find the approved ELF lubricant best suited to your vehicle, ask your Renault dealer for a recommendation or consult your vehi- cle maintenance handbook.
Page 3 This handbook may also contain information about items of equipment to be introduced later in the model year. Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle.
Page 5 Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
Page 7: Table Of Contents
The RENAULT card: general information and use ........
Page 8 KEY, RADIO FREQUENCY REMOTE CONTROL: general information (1/2) 1 Locks all the opening elements. 2 Unlocks all the opening elements. 3 Ignition and front door key. 5 Locking/unlocking of the boot only. Remote control with switchblade key: Driver’s responsibility 4 Locking/unlocking using the switch- when parking or stopping blade key.
Page 9 KEY, RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the surround- ings: take care not to lock or unlock the doors by inadvertently pressing the but- tons on the remote control. Replacement and additional keys or remote controls.
Page 10: Locking The Doors
RADIO FREQUENCY REMOTE CONTROL UNIT: use Note: The remote control A can be used to lock or unlock the doors and boot. With the engine running, the ignition It is powered by a battery which must switched on and in accessories position be replaced (refer to the information on (refer to “Ignition switch: vehicles with a “Radio frequency remote control: bat-...
Page 11 RADIO FREQUENCY REMOTE CONTROL UNIT: deadlocking If the vehicle is equipped with a dead- locking function, this allows you to lock the opening elements and to prevent the doors from being unlocked using the interior handles (for example, by breaking the window and then trying to open the door from the inside).
Page 12: Battery Life
(doors, tailgate) and the fuel ings. It is important to make sure when filler flap (see the following pages); handling the RENAULT card that you – switching on the vehicle lighting re- do not lock or unlock the doors by inad- motely (refer to the following pages);...
Page 13 RENAULT CARD: general information (2/2) Advice Avoid leaving the card in hot, cold or humid areas. Do not keep the RENAULT card in Driver’s responsibility a place where it could be bent or when parking or stopping damaged accidentally, such as in a the vehicle back pocket of a garment.
Page 14 Also, in hot and/or sunny weather, – the RENAULT card in remote con- any of the RENAULT card’s buttons, please remember that the tempera- trol mode. as long as the card is within the access ture inside the passenger compart- zone 1.
Page 15 Nota: the “hands-free” system may ex- Remote “Hands-free” locking perience temporary difficulties if one of With the RENAULT card in zone 1, With the RENAULT card on you, and the sensors built into the inside of the move your hand behind a handle 2: the...
Page 16 RENAULT CARD: use (3/5) “Hands-free” locking using the Special features of the locking If the RENAULT card has been within sensor 4 system range for approximately 15 minutes, remote locking is disabled. If you wish to lock your vehicle while the...
Page 17 Note: The maximum distance at which the vehicle locks depends on the sur- control roundings. Unlocking with the card RENAULT Special features Press button 6. Unlocking is indicated If the a door or the boot is open or not by one flash of the hazard warning properly closed, the vehicle cannot be lights and the indicator lights.
Page 18 RENAULT CARD: use (5/5) Locking/unlocking only the boot Press the button 8 to lock/unlock the boot only. Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-sufficient alone in your vehicle, even for a short time.
Page 19 RENAULT CARD: deadlocking If the vehicle is equipped with a dead- locking function, this allows you to lock the opening elements and to prevent the doors from being unlocked using the interior handles (for example, by breaking the window and then trying to open the door from the inside).
Page 20: Locking/Unlocking The Doors
If the remote control or, depending on the vehicle, the RENAULT card does not work In some cases, the radio frequency remote control or the RENAULT card may not work: – RENAULT card/radio frequency remote control battery worn or run flat, vehicle battery flat, etc.
Page 21 – Insert the key 2 into the lock and lock from the inside or by using the key in or unlock the front left-hand door. the front left-hand door. Once you are inside the vehicle, put the key back in its casing in the RENAULT card. 1.15...
Page 22 Unlocking the vehicle from the outside is only possible with the RENAULT card in the vehicle’s access zone or using Interior locking/unlocking the key.
Page 23: Opening And Closing The Doors
Opening the doors from the Opening from the inside outside Pull on the handle 2. With the doors unlocked or RENAULT card on you, hold handle 1 and pull it towards you. As a safety precaution, the doors should only be opened or closed when the vehicle is stationary.
Page 24 OPENING AND CLOSING THE DOORS (2/3) Once the vehicle reaches a speed of approximately 12 mph (20 km/h), a warning light indicates if the door(s) or luggage compartment are open or im- properly closed, along with the mes- sage “Boot open” or “Door open” and a beep will sound for around 40 seconds or until the door/luggage compartment is closed.
Page 25: Child Safety
OPENING AND CLOSING THE DOORS (3/3) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves or to others by starting the engine, Child safety activating equipment such as the...
Page 26: Automatic Locking When Driving
AUTOMATIC LOCKING WHEN DRIVING Activating/deactivating the Operating faults function If you experience an operating fault (no automatic locking, the indicator light in- To switch it on: with the vehicle at a corporated in switch 2 does not light up standstill and the engine running, press when trying to lock the doors and boot, switch 2 until a beep sounds.
Page 27: Front Headrests
FRONT HEADRESTS To adjust the angle of the headrest If your vehicle is thus equipped, move the A section towards or away from you to the required position To remove the headrest Raise the headrest to its highest po- sition (tilt the seatback backwards if necessary).
Page 28 FRONT SEATS (1/3) Settings To tilt the seatback Lift handle 3 and tilt the seatback to the To move the seat forwards or back desired position. Release the handle at For safety reasons, make Lift handle 1 to release. Release the the desired position and make sure that these adjustments only handle at the desired position and...
Page 29 FRONT SEATS (2/3) Repositioning the seat When using the passenger seat in table position, you must not use the two rear Make sure that nothing prevents the seats immediately behind it. seat from moving. – Pull the handle 7 and raise the seat- back, ensuring that it locks firmly in place.
Page 30 FRONT SEATS (3/3) Massage Driver Massage Tonic Relaxing Lumbar Intensity Speed Functions – adjust the intensity (+ or -); Heated seats – adjust the speed (+ or -); With the ignition on: Massage – reset the selected settings. Press 7 –...
Page 31: Steering Wheel
STEERING WHEEL Activating the function With the ignition on, press the switch 2, the warning light integrated in the switch lights up. Deactivating the function - Automatic: The function switches off automatically after the regulation phase of approxi- mately 30 minutes. The warning light integrated in the switch 2 remains on.
Page 32: Seat Belts
SEAT BELTS (1/4) Always wear your seat belt when trav- Before starting, first adjust your driv- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belts to ensure ticular country you are in.
Page 33 SEAT BELTS (2/4) Driver’s seat belt reminder ß and, depending on the vehi- cle, front passenger seat belt re- minder This lights up on the central display when the engine is started. If the driv- er’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approxi- mately 12.4 mph (20 km/h), it flashes...
Page 34 SEAT BELTS (3/4) Adjusting the height of the Rear seat belts 8 front seat belts The belts are locked, unlocked and adjusted in the same way as the front Use button 7 to adjust the seat belt belts. height so that the shoulder strap is worn as shown previously.
Page 35 SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...
Page 36 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt inertia reel pretension- an accident. ers; – No operation whatso- –...
Page 37: Methods Of Restraint In Addition To The Front Seat Belts
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter driver and passenger front Airbags Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger the belt against the body so that it is at sides.
Page 38 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operating faults å This warning light comes on when the engine is started and then goes out after approximately three sec- onds. If it does not come on when the ignition is switched on or if it stays on, there is a fault in the system.
Page 39 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when it inflates. Warnings concerning the driver’s airbag –...
Page 40 METHODS OF RESTRAINT IN ADDITION TO THE REAR SEAT BELTS Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...
Page 41 SIDE PROTECTION DEVICES Side air bags These air bags are fitted to the front seats and are activated at the sides of the seats (door side) to protect the oc- cupants in the event of a severe side impact. Curtain air bags These are airbags fitted along the sides of the vehicle in the ceiling which trigger along the front and rear door side win-...
Page 42: Additional Methods Of Restraint
ADDITIONAL METHODS OF RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt.
Page 43: Child Safety: General Information
CHILD SAFETY: General information (1/2) Carrying children Please ensure that you comply with the legislation of your country. Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. Driver’s responsibility A child is not a miniature adult.
Page 44 CHILD SAFETY: General information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
Page 45 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
Page 46: Choosing A Child Seat Mounting
CHILD SAFETY: choosing a child seat mounting (1/4) There are two ways of attaching child Attachment via the seat belt seats: via the seat belt or using the The seat belt must be adjusted to ISOFIX system. ensure that it is effective in the event of harsh braking or an impact.
Page 47 CHILD SAFETY: choosing a child seat mounting (2/4) Attachment using the ISOFIX Attach the child seat with the ISOFIX system locks, if these are provided. The ISOFIX system allows quick, easy, safe fitting. Approved child seats ISOFIX are stand- ardised in accordance with current reg- The ISOFIX system consists of 2 rings ulations if any of the four cases below and, in some cases, a third ring.
Page 48 CHILD SAFETY: choosing a child seat mounting (3/4) The rings are located on the rear seat-  backs and indicated by the symbol In all cases, attach the strap hook to the corresponding ring 3 or 4 and place the seat in the desired position.
Page 49 CHILD SAFETY: choosing a child seat mounting (4/4) The rings are located behind the rear  seats and indicated by the symbol Attach the strap hook to the corre- sponding ring 3 and place the vehicle seat in the desired position. Pull the belt so that the back of the child seat comes into contact with the back of the vehicle seat.
Page 50: Fitting A Child Seat, General Information
CHILD SAFETY: fitting a child seat, general information (1/2) Some seats are not suitable for fitting The types of child seat indicated may After installing the child seat, when this child seats. The diagram on the follow- not be available. Before using a differ- is possible, you can move the vehi- ing page shows you how to attach a ent child seat, check with the manufac-...
Page 51 CHILD SAFETY: fitting a child seat, general information (2/2) In the rear seat A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with his or her A child seat with floor sup- feet nearest the door.
Page 52 CHILD SEATS: attachment by seat belt (1/3) The table below summarises the information already shown in the diagram on the following pages, to ensure the appli- cable regulations are respected. Front passenger Type of child seat Weight of the child Rear side seats Rear centre seat seat (1)
Page 53 CHILD SEATS: attachment by seat belt (2/3) X = Seat not suitable for fitting child seats of this type. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. (2) A carrycot can be installed across the vehicle and will take up at least two seats.
Page 54 CHILD SEATS: attachment by seat belt (3/3) Fitting diagram ³ Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. Seat not suitable for fitting ² child seats. Child seat attached using the belt ¬...
Page 55 CHILD SEATS: attachment using the isofix system (1/3) Fitting diagram Child seat fitted using the ISOFIX mounting  Seat which allows an ISOFIX child seat to be fitted. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be attached.
Page 56 CHILD SEATS: attachment using the isofix system (2/3) The table below summarises the information already shown on the diagram on the previous pages, to ensure the regula- tions in force are respected. Weight of Front passenger Type of child seat Seat size ISOFIX Rear side seats Rear centre seat...
Page 57 CHILD SEATS: attachment using the isofix system (3/3) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be at- tached using the ISOFIX system; check that it can be fitted. i-U = Suitable for the i-Size restraint devices in the “universal”...
Page 58: Deactivating/Activating The Front Passenger Airbag
CHILD SAFETY: deactivating, activating the front passenger air bag (1/3) The front passenger air bag must only be deactivated or activated when the vehicle is stationary. If it is interfered with when the ve- hicle is being driven, indicator lights å...
Page 59 CHILD SAFETY: deactivating, activating the front passenger air bag (2/3) The markings on the dashboard and labels A on each side of the passen- ger sun visor 3 (example: label shown above) remind you of these instruc- tions. DANGER Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER...
Page 60 CHILD SAFETY: deactivating, activating the front passenger air bag (3/3) Operating faults It is forbidden to fit a rear-facing child seat to the front passenger seat if the airbag activation/deactivation system is faulty. Allowing any other passenger to sit in that seat is not recommended.
Page 61: Audible And Visual Signals
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. One-touch mode When driving, it is possible that the steering wheel may not be turned suf- ficiently to return the stalk automatically to its starting position.
Page 62 DRIVER’S POSITION, LEFT-HAND DRIVE (1/2) 1.56...
Page 63: Instrument Panel
2 Demister outlet. – hazard warning lights; 22 Engine start/stop button (vehicles 3 Stalk for: – electric door locking. with RENAULT card). – direction indicator lights; 13 Passenger Airbag location. 23 Ignition switch (vehicles with key). – exterior lights; 14 Glove compartment 24 Control for adjusting steering –...
Page 64: Driving Position
DRIVING POSITION: RIGHT-HAND DRIVE (1/2) 10 11 1.58...
Page 65 3 Passenger Airbag location. 10 Instrument panel. 17 Engine start/stop button (vehicles 4 Controls for: 11 Driver Airbag and horn location. with RENAULT card). – front seat heating; 12 Controls for: 18 Switches for: – activation/deactivation, depend- – on-board computer information –...
Page 66 WARNING LIGHTS (1/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Side light warning light š Main beam headlight tell- á tale Dipped beam headlight tell- tale Rear fog lights tell-tale Automatic main beam head- ...
Page 67 WARNING LIGHTS (2/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Low fuel level warning light Brake circuit fault warning Oil pressure warning light À It lights up orange when the ig- light It lights up when the ignition or nition or the engine is switched on then, It lights up when the ignition or the the engine is switched on and goes off...
Page 68: Warning Lights
WARNING LIGHTS (3/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Variable power-assisted Toxic Fume Filter System Anti-lock braking warning Ä steering warning light Warning Light light It lights up when the ignition or the On vehicles which are equipped with it, It lights up when the ignition or the engine is switched on and goes off after...
Page 69 WARNING LIGHTS (4/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Preheating warning light Air bag warning light Engine standby warning É å  (Diesel version) This warning light will be dis- light played on the instrument panel when This should come on when the igni- Please see information in the para- the ignition is switched on or the engine...
Page 70 WARNING LIGHTS (5/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Tyre pressure monitoring Assisted parking brake fault Free wheel warning light in    system light mode ECO Refer to the information on the “Tyre Please refer to the information on the It lights up in mode ECO when the pressure monitoring system”...
Page 71 WARNING LIGHTS (6/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Driver’s seat belt reminder ß and, depending on the vehi- cle, front passenger seat belt re- minder. This lights up when the ignition is switched on.
Page 72: Trip Computer And Warning System
DISPLAYS AND INDICATORS (1/6) Driving style indicator 3 Please refer to the information on “Eco- driving” in Section 2. Trip computer and warning system Refer to the information on the “Trip computer and warning system” in Section 1. Instrument panel A Rev counter 1 (graduations x 1000) lights up when the driver’s door is...
Page 73 DISPLAYS AND INDICATORS (2/6) Coolant temperature indicator 4 Fuel gauge 6 In normal use, indicator 4 should be If the level is at the minimum, warn- before area 5. Under “intensive” oper- ing light integrated in the indica- ating conditions, the needle may ap- tor comes on orange, accompanied by proach this zone.
Page 74 DISPLAYS AND INDICATORS (3/6) Instrument panel B Rev counter 7 Driving style indicator 9 (graduations x 1000) Please refer to the information on “Eco- lights up when the driver’s door is driving” in Section 2. opened. In some cases, the appear- Speedometer 8 ance of a warning light is accompanied This is displayed differently according...
Page 75: Displays And Indicators
DISPLAYS AND INDICATORS (4/6) Instrument panel in miles (option to switch to km/h) Vehicles not fitted with a multimedia system 13 14 – With the ignition off, press the OK button 13 and the engine start/stop button 15; – using control 14, select “Settings”, “Instrument panel”, then the unit;...
Page 76 DISPLAYS AND INDICATORS (5/6) You can adjust certain settings from the multimedia screen: with the engine running, access the menu “System”, “Display”, then “Head-up display”. Adjusting the display information height Depending on your driving position, you can raise or lower the information on the display.
Page 77 DISPLAYS AND INDICATORS (6/6) Operating faults In the event of a malfunction (the dis- play fails to open when the engine is started, or the display retracts, with the engine running, following an object im- pacting the display): – stop and restart the engine; –...
Page 78 TRIP COMPUTER: general information (1/2) Display selection keys 2 Scroll through the following information by repeated short presses on button 2 (the display depends on the vehicle equipment and country): a) total mileage and trip mileage re- corder; b) journey parameters: –...
Page 79 ON-BOARD COMPUTER: general information (2/2) Interpreting some of the values displayed after resetting The values showing average fuel con- sumption and average speed will become more stable and reliable the further you have travelled since the last time the Reset button was pressed. The average fuel consumption may de- crease when: –...
Page 80 ON-BOARD COMPUTER: trip settings (1/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101778 km 112.4 km a) Total mileage and trip mileage recorder. Middle b) Journey parameters: Average fuel consumption.
Page 81 ON-BOARD COMPUTER: trip settings (2/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Range b) Journey parameters (continued): Estimated range with remaining fuel. 541 km The value is displayed after driving 400 metres. Distance Distance travelled since last reset.
Page 82 ON-BOARD COMPUTER: trip settings (3/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with mileage- before-service message d) Mileage before service or oil change. Mileage before service Service in With the ignition switched on, the engine not running and Service Intervals...
Page 83 TRIP COMPUTER: trip settings (4/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with distance before next service message (cntd.) d) Mileage before service or oil change. Mileage before service Oil change in With the ignition on, the engine not running and the display...
Page 84 ON-BOARD COMPUTER: trip settings (5/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected e) Reset the tyre pressure. Refer to the information on the “Tyre pressure Tyre pressure monitoring system”...
Page 85 TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpreting the display selected “Parking brake on”...
Page 86 TRIP COMPUTER AND WARNING SYSTEM: operating fault messages © These appear with the warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.
Page 87 TRIP COMPUTER AND WARNING SYSTEM: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traf- fic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Some examples of warning messages are given below.
Page 88: Vehicle Settings Customisation Menu
VEHICLE SETTINGS CUSTOMISATION MENU (1/2) Adjusting the settings Select the function to modify: a) Free wheel in ECO mode; (please refer to the information on “Driving advice, ECO-driving” in Section 2) b) Auto door lock while driving; c) Use handsfree card: open/close; d) Indicator sound volume;...
Page 89 VEHICLE SETTINGS CUSTOMISATION MENU (2/2) Adjusting the settings Once a line has been selected, press the switch 3 OK to adjust the function. Browse using the control 4 to select the function to adjust: If you select either “PARKING ASSIST VOLUME”...
Page 90: Power-Assisted Steering
POWER-ASSISTED STEERING Power-assisted steering Variable power-assisted steering The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) while the force needed to steer increases progressively as the speed rises (for enhanced safety at high speeds).
Page 91: Clock And Exterior Temperature
CLOCK AND EXTERIOR TEMPERATURE External temperature indicator Special note: When the exterior temperature is be- tween –3 °C and +3 °C, the characters °C flash and the message “Risk of black ice” is displayed on the instru- ment panel 1. The time and/or external tempera- ture are displayed on the multifunc- tion screen 2...
Page 92: Rear View Mirrors
Automatic mode is then deactivated. To – when the ignition is next switched on reactivate it, position switch 3 to B. (function deactivated); – upon detecting the RENAULT card or upon unlocking the vehicle (func- tion activated). Exterior rear view mirrors...
Page 93: Interior Rear View Mirror
REAR VIEW MIRRORS (2/2) Special feature: Interior rear view mirror When the rear-view mirror has been Rear view mirror with lever 4 manually deployed or folded back, it is possible to reset it to a usage position. When driving at night, to avoid being To do this, position the switch 3 to C.
Page 94: Headlight Beam Adjustment
HEADLIGHT BEAM ADJUSTMENT (1/2) Halogen bulb versions Examples of positions for adjusting control A according to the load 5 doors Estate 4 doors Driver alone or with front passenger All seats occupied 1 or 2 On vehicles fitted with this function, control A allows you to adjust the height Driver with passengers and of the beams according to the load.
Page 95 HEADLIGHT BEAM ADJUSTMENT (2/2) LED versions Examples of positions for adjusting control A according to the load 5 doors Estate 4 doors Driver alone or with front passenger All seats occupied Driver with passengers and luggage (or load) reaching the 2 or 3* 2 or 3* maximum permissible all-up...
Page 96: Exterior Lighting And Signals
EXTERIOR LIGHTING AND SIGNALS (1/6) Dipped beam headlights Manual operation Turn ring 3 until the symbol is opposite mark 2. This indicator light on the in- strument panel comes on. Automatic operation Turn the ring 3 until the AUTO symbol is opposite the mark 2: with the engine running, the dipped beam headlights switch on or off automatically depend-...
Page 97 EXTERIOR LIGHTING AND SIGNALS (2/6) Automatic main beam  headlights Depending on the vehicle, this system switches the main beam headlights on and off automatically. The function uses a camera located behind the interior rear-view mirror to detect vehicles that are following and coming in the oppo- site direction.
Page 98 EXTERIOR LIGHTING AND SIGNALS (3/6) – repeatedly press the control 6 up or down until you reach the Automaticmain beam lights menu, then press the switch 5 OK. – press the switch 5 OK again to acti- vate or deactivate the function: Activation/deactivation To activate automatic main beam headlights:...
Page 99: Daytime Running Lights
EXTERIOR LIGHTING AND SIGNALS (4/6) Automatic main beam Operating faults  headlights (continued) When the message “Check lighting” © with warning light is displayed Operating faults When the message “Check auto light- and warning light flashes on the ing” appears on the instrument panel, instrument panel, this indicates that the system is deactivated.
Page 100 With the engine and lights switched vehicle or when opening a door. ing the RENAULT card or when the ve- off and the ring 3 in position 0 or AUTO, hicle is unlocked. They switch off automatically:...
Page 101: Rear Fog Lights
EXTERIOR LIGHTING AND SIGNALS (6/6) Rear fog lights Switching off the lights Turn centre ring 7 on the stalk Turn the ring 7 again until the mark 2 until the symbol faces mark 2, then re- is opposite the symbol for the fog light lease it.
Page 102: Windscreen Wipers
WINDSCREEN WASH, WIPE (1/6) Efficiency of a wiper blade Check the condition of the wiper blades. How long they last depends on you: – it must remain clean: clean the blade and the screen regularly with soapy water; – do not use it when the screen is dry;...
Page 103 WINDSCREEN WASH, WIPE (2/6) When activating automatic wiping or when increasing sensitivity, one sweep of the blades is performed. Note: – the rain sensor is only intended as a driving aid. In the event of reduced visibility, the driver should manually activate the wipers.
Page 104 WINDSCREEN WASH, WIPE (3/6) Operating fault Special note In the event of a malfunction of the au- When driving the vehicle, the wiping tomatic wiping, the wiper is set to inter- speed slows down whenever the vehi- mittent wiping. Contact an authorised cle stops.
Page 105: Service Position
WINDSCREEN WASH, WIPE (4/6) Specific front wiper position Note: after replacement, to reposition the blades correctly, make sure the (service position) blades are resting on the windscreen, This position enables the blades to be switch on the ignition and activate the lifted to remove them from the winds- wiper control.
Page 106: Windscreen Washer
WINDSCREEN WASH, WIPE (5/6) Note: in temperatures below zero, the washer liquid may freeze on the wind- screen, reducing visibility. Heat the windscreen using the demister control before cleaning. Windscreen washer With the ignition on, pull stalk 1 then release. A brief pull will trigger a single sweep of the wipers, in addition to the wind- screen washer.
Page 107: Headlight Washers
WINDSCREEN WASH, WIPE (6/6) Note: to ensure the headlight wash- ers operate correctly in winter, remove snow from the jet trims and de-ice the jet trims using an aerosol de-icer. You are recommended to regularly remove dirt encrusted on the headlight glass.
Page 108: Rear Screen Wiper
REAR SCREEN WASH, WIPE (1/2) To stop the operation, pivot ring 3 again. Note: when washing using a roller type car wash, return the ring 3 on the stalk 1 to the stop position to deactivate Efficiency of a wiper blade automatic wiping.
Page 109 REAR SCREEN WASH, WIPE (2/2) Activation/deactivation of the rear In the event of obstacles present on the screen wiper rear window (dirt, snow, etc.), the wiper will try to sweep away all the obstacles. Engaging reverse gear triggers inter- If an obstacle prevents the blade from mittent wiping (if the front wipers are in moving, it can be stopped.
Page 110: Fuel Tank (Filling With Fuel)
FUEL TANK (1/3) Useable fuel tank capacity: For details on filling the fuel tank, refer Fuel grade to the information on “Filling with fuel”. – About 11 gallons (50 litres) for Use a high-grade fuel that complies petrol versions; To close it, press on the fuel filler flap by with the legislation in force in each hand, as far as it will go.
Page 111: Diesel Versions
FUEL TANK (2/3) Filling with fuel Petrol versions Using leaded petrol will damage the With the ignition off, insert the nozzle to antipollution system and may lead to a open valve 3 and insert it fully before loss of warranty. turning it on to fill the fuel tank (risk of splashing).
Page 112 – If the engine does not start after sev- eral attempts, please contact an au- Vehicles with RENAULT card thorised dealer. With the card RENAULT in the pas- Persistent smell of senger compartment, press the start fuel button 4 without pressing any of the pedals.
Page 113 Starting - Stopping the engine: vehicle with RENAULT card .......
Page 114: Running In
RUNNING IN Petrol version Diesel version For the first 600 miles (1,000 km), do For the first 1,000 miles (1,500 km), not exceed 78 mph (130 km/h) in the do not exceed 80 mph (130 km/h) in highest gear, or 3,000 to 3,500 rpm. the highest gear, or 2,500 rpm.
Page 115: Ignition Switch
IGNITION SWITCH: vehicle with key “ON" 2 position The ignition is switched on: Accessories (radio etc.) can be used. “START" 3 position If the engine fails to start at the first attempt, the key must be turned back before the starter can be activated again.
Page 116: Starting, Stopping The Engine: Vehicle With Key/Remote Control Unit
STARTING, STOPPING THE ENGINE: vehicle with key Stopping the engine Diesel versions É With the engine idling, turn the key – Turn the ignition key to the “ON" po- back to the “LOCK" position 0. sition 2 and hold this position until the engine preheating light goes off;...
Page 117: Starting - Stopping The Engine: Vehicle With Renault Card
STARTING, STOPPING THE ENGINE: vehicle with RENAULT card (1/3) “Hands-free” starting with the tailgate open In this case, the RENAULT card should not be located in the boot, to avoid any risk of loss. Driver’s responsibility when parking or stopping...
Page 118 STARTING, STOPPING THE ENGINE: vehicle with RENAULT card (2/3) Accessories function Operating faults Press the brake or clutch pedal, then place the RENAULT 3 card (logo side) (switching on the ignition) In certain cases, the RENAULT “hands- for around 2 seconds in contact with.
Page 119 STARTING, STOPPING THE ENGINE: vehicle with RENAULT card (3/3) If the RENAULT card is no longer in the When you leave your vehi- passenger compartment when you try cle, especially if you have to switch the engine off, the message your RENAULT card with “No keycard Press and hold”...
Page 120: Standing Start Procedure
STANDING START PROCEDURE (1/2) Activating the system The system is activated by: – with the engine running, and the ve- hicle stationary; – Sport mode activated (please see the “Multi-Sense” section); – depress the brake pedal with the left Heavy use of the system will reduce foot;...
Page 121 STANDING START PROCEDURE (2/2) Conditions for non-activation of the system Certain conditions will not enable the system to be activated: – five successive authorised standing start procedures - beyond five proce- dures being performed, the function will be prevented for approximately 10 minutes;...
Page 122 FUNCTION STOP AND START (1/4) This system enables a reduced fuel For manual gearboxes: For all vehicles: consumption and lower greenhouse  – the gearbox is in neutral; The warning light on the instru- gas emissions. ment panel is lit when the engine is on –...
Page 123 FUNCTION STOP AND START (2/4) Preventing the engine from Conditions for coming out of Special note: depending on the vehi- cle, if you switch off the ignition when standing by engine standby the engine is on standby, the warning In certain situations, such as negotiat- For automatic gearboxes: Ä...
Page 124 Special case for vehicles with – for vehicles with automatic gear- boxes, the gradient is steeper than standby of the engine a RENAULT card approximately 12%; Certain conditions prevent the system With the engine on standby (traffic jam, – the “Clear View” function is activated from using the engine standby function, traffic lights, etc.), if the driver unfas-...
Page 125 FUNCTION STOP AND START (4/4) Special feature of the automatic The system is automatically reacti- engine re-start vated each time the vehicle is started (see “Starting, stopping the engine” in Under certain conditions, the engine Section 2). can restart on its own in order to guar- antee your safety and comfort.
Page 126: Special Features Of Petrol Versions
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...
Page 127: Special Features Of Diesel Versions
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with an injec- tion pump which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.
Page 128: Gear Lever/Handbrake
GEAR LEVER/HANDBRAKE Handbrake To apply: Pull lever 3 upwards. Check that the To release: vehicle is immobilised. The warning Pull the lever 3 up slightly, press light on the instrument panel will button 2 and then lower the lever to the come on.
Page 129: Electronic Parking Brake
ELECTRONIC PARKING BRAKE (1/3) Note: To indicate that the electronic parking brake is released, a beep sounds and the message “Apply parking brake” ap- pears on the instrument panel: – with the engine running: when the driver’s door is opened; –...
Page 130: Manual Operation
ELECTRONIC PARKING BRAKE (2/3) Special cases To park on a slope or while towing a trailer, for example, pull switch 2 for a few seconds to gain the maximum braking. To park the vehicle without applying the electronic parking brake (if there is a risk of freezing, for example): –...
Page 131 ELECTRONIC PARKING BRAKE (3/3) Versions with an automatic Operating faults gearbox © – If there is a fault, the warning light illuminates on the instrument For safety reasons, automatic release panel accompanied by the “Check is deactivated when the driver’s door parking brake”...
Page 132: Driving Advice, Eco-Driving
DRIVING ADVICE, ECO-DRIVING (1/5) Fuel consumption is accredited in ac- cordance with a standard regulatory method. Identical for all manufactur- ers, this enables vehicles to be com- pared with one another. Consumption in real time depends on vehicle usage conditions, the equipment fitted and the user’s driving style.
Page 133 DRIVING ADVICE, ECO-DRIVING (2/5) An overall rating from 0 to 100 is dis- played to let you assess your eco driv- ing performance. The higher the rating, the lower the fuel consumption. Eco advice is given to help improve your performance. With your favourite journeys saved, you can compare your performance between trips and the performance of...
Page 134 DRIVING ADVICE, ECO-DRIVING ( 3/5) ECO mode Activating the function The function can be activated: ECO mode is a function which opti- mises fuel consumption. It acts upon – by pressing switch 5; certain power consuming systems in – by pressing the switch 6 (please refer the vehicle (heating, air conditioning, to the information on “Multi-Sense”...
Page 135 DRIVING ADVICE, ECO-DRIVING (4/5) – Do not overrev the engine in the in- – Bad weather, flooded roads: termediate gears. You should always use the highest Do not drive through gear possible. floods if the water is – Avoid sudden acceleration. above the lower edge of –...
Page 136 DRIVING ADVICE, ECO-DRIVING (5/5) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (espe- cially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Page 137: Maintenance And Antipollution Advice
MAINTENANCE AND ANTIPOLLUTION ADVICE Your vehicle complies with criteria for In addition, replacing engine, fuel – Air filter, fuel filter: a choked ele- recycling and recovering vehicles at the supply system and exhaust compo- ment will reduce efficiency. It must end of their service life, which entered nents with parts other than those origi- be replaced.
Page 138: Environment
– In all cases, comply with local legis- while in use, and therefore to consume This commitment is illustrated by the lation. less fuel (e.g. 140 g/km, equivalent to Renault eco² signature. 1494.6 mpg (5.3 l/100 km) for a diesel vehicle). Recycling Manufacture...
Page 139: Tyre Pressure Monitoring System
TYRE PRESSURE MONITORING SYSTEM (1/3) Resetting the standard level Resetting procedure for the tyre pressures With the ignition on: – repeatedly and briefly press con- This should be done: trol 2 to select the tyre pressure dis- – when the standard tyre pressure play and, depending on the vehicle, needs to be changed to adapt to the “Tyre pressure”...
Page 140 TYRE PRESSURE MONITORING SYSTEM (2/3) “Puncture” A wheel B is shown, depending on the vehicle, in red or white accompanied  by the warning light 4 fixed, the message “Puncture” and a beep. This message appears along with the ® warning light.
Page 141 Because the valves are specially de- or more wheels have been fitted with Please see the information on “Tyres” signed, only use equipment approved sensors not recognised by Renault. in Section 5. by the approved network. Please refer Contact an approved Dealer to fit new to “Tyre inflation kit”...
Page 142: Driver Correction Devices/Aids
DRIVER CORRECTION DEVICES AND AIDS (1/10) ABS (anti-lock braking – ABS (anti-lock braking system); system) – ESC (electronic stability control) Under heavy braking, the ABS prevents with understeer control and trac- the wheels from locking, allowing the tion control; stopping distance to be managed and –...
Page 143 DRIVER CORRECTION DEVICES AND AIDS (2/10) Operating faults: © – lit up on the in- strument panel accompanied by the messages “Check ABS”, “Check braking system” and “Check ESC”: this indicates that the ABS, the ESC and the emergency brake assist are disabled.
Page 144: Electronic Stability Control
DRIVER CORRECTION DEVICES AND AIDS (3/10) Electronic stability control Understeer control Operating faults ESC with understeer control This system optimises the action of the When the system detects an operat- and traction control ESC in the case of pronounced under- ing fault the message “Check ESC”...
Page 145: Emergency Brake Assist
DRIVER CORRECTION DEVICES AND AIDS (4/10) Emergency brake assist Braking anticipation Depending on the vehicle, when you This system supplements the ABS rapidly release the accelerator, the and helps reduce vehicle stopping dis- system anticipates the braking ma- tances. noeuvre in order to reduce stopping Operating principle distances.
Page 146 DRIVER CORRECTION DEVICES AND AIDS (5/10) If the driver depresses the brake pedal and the system still detects a risk of col- lision, the brake force is increased. If the driver fails to react following an alert of an imminent collision, the system activates the brakes.
Page 147 DRIVER CORRECTION DEVICES AND AIDS (6/10) Press the switch 5 OK again to activate or deactivate the function: function activated < function deactivated  The warning light is displayed on the instrument panel when the system is deactivated. This system is reactivated each time the ignition is switched on.
Page 148 DRIVER CORRECTION DEVICES AND AIDS (7/10) Operating faults Active emergency braking When the system detects an operating This function is an additional driving aid. This function is not under any  fault, the warning light lights up circumstances intended to replace the due care and attention of the on the instrument panel, with the mes- driver, who should at all times be in control of the vehicle.
Page 149 DRIVER CORRECTION DEVICES AND AIDS (8/10) Active emergency braking Limitation of the system operation – The system will only respond to vehicles which are moving or which have been sensed as moving. – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. –...
Page 150 DRIVER CORRECTION DEVICES AND AIDS (9/10) Hill start assistance Depending on the gradient of the in- cline, this system assists the driver when starting on a hill. It prevents the vehicle from rolling backwards by au- tomatically applying the brakes when the driver lifts his/her foot off the brake pedal to depress the accelerator pedal.
Page 151 DRIVER CORRECTION DEVICES AND AIDS (10/10) Operating faults © – If the warning light, together with the message “Check power steering”, is displayed on the instru- ment panel: please contact an au- thorised dealer. ® – If the warning light , together with the message “Power steering fault”, is displayed on the instrument...
Page 152: Lane Departure Warning
LANE DEPARTURE WARNING (1/3) This system notifies the driver when they accidentally cross a continuous or broken line. This function uses a camera attached to the windscreen, behind the rear-view mirror. This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle.
Page 153 LANE DEPARTURE WARNING (2/3) Activation/deactivation Vehicles not fitted with a navigation The function is set to notify the system driver if: Vehicles fitted with a navigation – the vehicle speed is greater than ap- Press the switch 3. system proximately 45 mph (70 km/h); From the multimedia screen 1: select Operation –...
Page 154 LANE DEPARTURE WARNING (3/3) Adjustment – repeatedly press the control 7 up or down until you reach the Lane de- Vehicles fitted with a navigation parture warning setting menu, then system press the switch 6 OK . – Volume: adjust the alert volume to From the multimedia screen 1, select one of three levels;...
Page 155: Blind Spot Warning
BLIND SPOT WARNING (1/4) This function is an addi- tional aid which indicates other vehicles in the blind spot area. This system alerts the driver to other Special feature It can never in any case be a sub- vehicles in the detection zone A. Make sure that the sensors are not ob- stitute for care nor for the driver’s The system is activated when the vehi-...
Page 156 BLIND SPOT WARNING (2/4) – repeatedly press the control 5 up or down until you reach the Blind spot alert menu, then press the switch 4 – Press the switch 4 OK again to acti- vate or deactivate the function. Activation/deactivation Vehicles not fitted with a navigation system...
Page 157 BLIND SPOT WARNING (3/4) Display B The function is activated and has not detected any vehicles. Display C First warning: the indicator 6 means that a vehicle has been detected in the blind spot. Display D When the direction indicator is acti- vated, the indicator light 6 flashes when a vehicle is detected in the blind spot on the side towards which you are about to...
Page 158 BLIND SPOT WARNING (4/4) Operating faults If the system detects a fault, the mes- sage “Check blind spot alert” is dis- played on the instrument panel. Consult an approved dealer. Note: when the engine is started, the indicator light 6, display B, flashes three times.
Page 159: Safe Distance Alert
SAFE DISTANCE ALERT (1/2) Using the sensor 1, this function noti- Activating/deactivating the fies the driver about the time interval function separating them from the vehicle in From the multimedia screen 2, select front, so they can respect a safe dis- the “Vehicle”...
Page 160 SAFE DISTANCE ALERT (2/2) – C (orange): the time interval falls between around 1 and 2 seconds (in- sufficient distance between the two This function is essential if adaptive vehicles); cruise control is activated. – D (red): the time interval is less than or equal to around one second (very insufficient distance between the two vehicles).
Page 161: Fatigue Detection Warning
FATIGUE DETECTION WARNING (1/2) The fatigue detection warning is a func- tion which is useful on monotonous roads (motorways, high-speed roads etc.). It analyses driver behaviour and takes account of events to inform you of any risk of fatigue such as: –...
Page 162 FATIGUE DETECTION WARNING (2/2) – repeatedly press control 5 up or Note: down until you reach the “Fatigue de- – if the warning is not deleted by press- tection warn.” menu, then press the ing switch 4 OK, the beep repeats; switch 4 OK.
Page 163: Speed Limiter
SPEED LIMITER (1/3) Switching on  Press switch 1 on side . Depending  on the vehicle, the warning light  is orange and the message “Speed limiter” appears on the instru- ment panel accompanied by dashes to indicate that the speed limiter function is activated and waiting to memorise a limit speed.
Page 164 SPEED LIMITER (2/3) Varying the limit speed Exceeding the limit speed The speed limiter can be changed by It is possible to exceed the limit speed repeatedly pressing switch 2 : at any time. To do this: press the accel- erator pedal firmly and fully (beyond –...
Page 165 SPEED LIMITER (3/3) Recalling the limit speed If a speed has been stored, it can be re- called by pressing switch 3 (R). Putting the function on Switching off the function standby The speed limiter function is deac- tivated if you press switch 1: in this The speed limiter function is suspended case a speed is no longer stored.
Page 166 OVERSPEED ALERT (1/3) Operating principle For vehicles equipped with a navigation system and if the vehicle is travelling in The system detects speed limit signs a country where the speed units differ on the side of the road and displays the from those of the vehicle, the system speed limit.
Page 167 OVERSPEED ALERT (2/3) – repeatedly press the control 6 up or down until you reach the Speed alert menu, then press the switch 5 OK. – Press OK to turn the function on or off. Varying the limit speed If the speed limiter notification differs from the detected speed value, press and hold the switch 4: –...
Page 168 OVERSPEED ALERT (3/3) Operating faults This function is an additional driving aid. This function is not under any The system cannot detect the speed circumstances intended to replace the due care and attention of the limit if: driver, who should at all times be in control of the vehicle. –...
Page 169: Cruise Control
CRUISE CONTROL (1/4) 4 This control is only activated for ve- hicles fitted with adaptive cruise control (refer to the information on “adaptive cruise control” in sec- tion 2). This function is an addi- tional driving aid. This func- tion does not take the place of the driver.
Page 170 CRUISE CONTROL (2/4) Activating cruise control At a steady speed (above approx. 20 mph or 30 km/h), press switch 2 side a (+): the function is activated and the current speed is saved. The cruising speed replaces the dashes and cruise control is confirmed by dis- playing of the cruising speed, the mes- sage “Cruise control”...
Page 171 CRUISE CONTROL (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes on the in- strument panel. Then, release the accelerator: after a few seconds, the vehicle will automati- cally return to its set cruising speed.
Page 172 CRUISE CONTROL (4/4) Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road con- ditions are suitable (traffic, road sur- face, weather conditions, etc.). Press switch 3 (R) if the vehicle speed is above 20 mph (30 km/h).
Page 173: Adaptive Cruise Control
ADAPTIVE CRUISE CONTROL (1/7) When traffic conditions permit (large free-flowing road or motorway), the adaptive cruise control gives you the option of maintaining a chosen speed, known as the cruising speed, which can be set from 31 mph to 87 mph (50 and 140 km/h), or 93 mph (150 km/h) de- pending on the vehicle, while keeping a following distance from the vehicle in...
Page 174 ADAPTIVE CRUISE CONTROL (2/7) Controls Switching on The cruising speed replaces the dashes and cruise control is confirmed by the Press switch 5. Warning light  5 Main “On/Off” switch. appearance of the message “Adaptive comes on, lit green, and the message 2 Controls for: cruise ctrl”...
Page 175 ADAPTIVE CRUISE CONTROL (3/7) Driving Varying the following distance Once a cruising speed is memorised and the cruise control function is active, You can vary the following distance you may lift your foot off the accelera- from the vehicle in front at any time by tor pedal.
Page 176 ADAPTIVE CRUISE CONTROL (4/7) Putting the function on Returning to the cruising speed standby If a speed is stored, it can be recalled, once you are sure that the road con- The function is set to standby if: ditions are suitable (traffic, road sur- –...
Page 177 ADAPTIVE CRUISE CONTROL (5/7) Note: if the speed previously stored is much higher than the current speed, the vehicle will accelerate to reach this threshold. Under certain conditions (coming up behind a vehicle moving much more slowly, rapid change of lane of vehi- cles in front etc.), the system may not have time to respond and may emit a beep alongside alert D when situations...
Page 178 ADAPTIVE CRUISE CONTROL (6/7) Operating faults When the system detects an operating  fault, the warning light lights up on the instrument panel, with the mes- sage “Check cruise control”. There are two possibilities: – the system is temporarily disrupted (for example: radar obscured by dirt, mud, snow etc.).
Page 179 ADAPTIVE CRUISE CONTROL (7/7) Limitation of the system operation – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. – The sensor area should be kept clean and free of any modifications in order to ensure the proper operation of the system.
Page 180: Parking Distance Control
PARKING DISTANCE CONTROL (1/5) Operating principle Ultrasonic sensors in the rear bumper measure the distance between the ve- hicle and an obstacle. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 20 to This function is an addi-...
Page 181 PARKING DISTANCE CONTROL (2/5) Note: the display 2 shows the vehicle Operation surroundings and emits beeps. Most objects located less near the It is necessary to travel a few metres front, rear and sides of the vehicle are before the side detection is activated. detected.
Page 182 PARKING DISTANCE CONTROL (3/5) If a side obstacle is detected: – the beeps become faster and then sound continuously as the obstacle gets nearer. Green, orange and red zones will be displayed on the dis- play D; – if there is no risk of collision, no beep will sound when approaching the ob- stacle.
Page 183 PARKING DISTANCE CONTROL (4/5) System sound Enables the system sound to be chosen. Deactivating the system sound Activate or deactivate the parking dis- tance control sound. Note: if you deactivate the sound, you will no longer be notified with beeps when approaching an obstacle.
Page 184 PARKING DISTANCE CONTROL (5/5) Automatic deactivation of the Operating faults parking distance control When the system detects an operating fault, a beep sounds for approximately The system deactivates: 3 seconds each time reverse gear is se- – when the vehicle speed is above ap- lected and is accompanied by the mes- proximately 6 mph (10 km/h);...
Page 185: Reversing Camera
REVERSING CAMERA (1/2) The 1 rear view camera is located on Special feature the luggage compartment lid. Make sure that the 1 camera is not ob- scured (by dirt, mud, snow, condensa- tion etc.). This function is an additional aid. It cannot, therefore, under any circum- stances replace the vigilance or the responsibility of the driver.
Page 186 REVERSING CAMERA (2/2) 4 moving guide line: This is shown in blue on the multime- dia screen 2. It indicates the vehicle tra- jectory according to the position of the steering wheel. Activating, deactivating the reversing camera From the multimedia screen 2, select “Vehicle”, “Parking assistance”, “Rear view camera”.
Page 187: Assisted Parking
ASSISTED PARKING (1/4) This function assists with parking ma- Switching on Special features noeuvres. With the vehicle stationary or driv- Ensure that the ultrasonic sensors indi- Take your hands off the steering wheel. ing at less than approximately 19 mph cated by arrows 3 are not obscured (by You only control the pedals and the (30 km/h), press the switch 1.
Page 188 ASSISTED PARKING (2/4) Choice of manoeuvre Operation Your speed should not exceed around 4 mph (7 km/h). The system can perform four types of Parking  manoeuvres: Once the warning light on the As long as the vehicle speed is less –...
Page 189 ASSISTED PARKING (3/4) Your speed should not exceed around In this case, the reason for suspending 4 mph (7 km/h). the manoeuvre will be displayed on the Once in position to exit the space, the multimedia screen. system will notify you of the end of the Make sure: manoeuvre.
Page 190 ASSISTED PARKING (4/4) This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. Make sure that the manoeuvre complies with the applicable traffic regulations at your location. –...
Page 191: Selector Lever
AUTOMATIC TRANSMISSION (1/3) Selector lever 1 Operation Gear shift paddles 3 (depending on the vehicle) P: park With the selection lever 1 in position P, switch on the ignition. The paddles 3 enable you to change R: reverse gear while the gear lever is in “manual To move out of position P, you must de- N: Neutral mode”...
Page 192: Automatic Gearbox
AUTOMATIC TRANSMISSION (2/3) Driving in automatic mode Driving in manual mode Special circumstances With the selector lever in position D, Put lever 1 into position D. – If the bends and road surface do move the lever to the left into the M po- not allow you to stay in automatic In most road conditions you will en- sition.
Page 193: Automatic Transmission
AUTOMATIC TRANSMISSION (3/3) Parking the vehicle Operating faults When the vehicle is stopped, move the – when driving, if the message lever to position P while keeping your “Check auto gearbox” appears on foot on the brake pedal: the gearbox is the instrument panel, it indicates a in neutral and the drive wheels are me- failure.
Page 194 2.82...
Page 195 Section 3: Your comfort Multi-Sense ..............Air Vents .
Page 196: Multi-Sense
MULTI-SENSE (1/2) Mode Eco Depending on the mode selected and Multi-Sense depending on the vehicle, the Multi- Mode Eco is geared towards saving Sense system controls the driving, Sport energy and the environment. The the ambient lighting, and the tone and Neutral Comfort Perso...
Page 197 MULTI-SENSE (2/2) Mode Comfort This mode favours smooth steering. The interior environment is softened. Depending on the vehicle, the driver’s seat massage function is activated. Mode Perso This mode enables you to manually configure the drive, comfort, light envi- ronment and engine noise. Accessing the menu Depending on the vehicle, once the “Multi-Sense"...
Page 198 AIR VENTS: air outlets (1/2) 1 side window demister outlets 2 side air vents 3 windscreen demister outlet 4 centre air vents 5 footwell heater outlets for front pas- 7 footwell heater outlets for rear pas- sengers sengers 6 multimedia screen 8 centre console air vents...
Page 199 AIR VENTS: air outlets (2/2) Front seats Air flow Rear seats Turn control knob 9: Direction Right/left direction  : maximum air flow; Move cursor 11. Right/left direction  : closed. Move cursor 8. Up/down direction To remove bad odours from your ve- Move cursor 11.
Page 200 MANUAL AIR CONDITIONING (1/3) 9 10 11 The controls Indicators Switching air conditioning on or 1 Air temperature adjustment/”Clear The following indicators are displayed View” function on the multimedia screen A: The air conditioning is switched on (in- dicator light on) or off (indicator light off) 2 De-icing/demisting of the rear screen 8 Air temperature.
Page 201: Manual Air Conditioning
MANUAL AIR CONDITIONING (2/3) Distribution of air in the passenger compartment There are five air distribution options. Turn control 5 to choose the distribution option. The air distribution is displayed on the multimedia screen. The air flow is directed to the õ...
Page 202 MANUAL AIR CONDITIONING (3/3) Varying the ventilation speed You can adjust the fan speed by press- ing the controls 6 or 7 to increase or reduce the fan speed. The system is deactivated (OFF): the ventilation speed is zero (vehicle sta- tionary).
Page 203: Automatic Climate Control
AUTOMATIC CLIMATE CONTROL: Controls A (1/5) Automatic mode Climate The automatic climate control system guarantees comfort in the passen- ger compartment and good visibility (except in the event of extreme condi- tions), while optimising consumption. The system controls the ventilation speed, air distribution, air recirculation, and starting and stopping the air condi- tioning and air temperature.
Page 204 AUTOMATIC CLIMATE CONTROL: Controls A (2/5) Note: the air conditioning configura- Climate tion depends on the mode selected in the “Multi-Sense" menu (please refer to the information on "Multi-Sense" in Section 3). The displayed temperature values Varying the ventilation speed Temperature adjustment show a comfort level.
Page 205 AUTOMATIC CLIMATE CONTROL: Controls A (3/5) To exit this function, press either: Climate – button 4; – again button 6; – on button 8, 9 or 10. Clear View function Press button 6 – the integrated indica- tor light comes on. This function quickly demists and de- Press button 3 to stop the heated rear ices the windscreen, the rear screen,...
Page 206 AUTOMATIC CLIMATE CONTROL: Controls A (4/5) Rear screen de-icing/ Climate demisting Press button 3 – the integrated indica- tor light comes on. This function en- ables rapid demisting or de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles). To exit this function, press button 3 again.
Page 207 AUTOMATIC CLIMATE CONTROL: Controls A (5/5) Automatic usage Climate Press button 16 (a warning light comes on in zone 14). Manual use Press button 5 to force air recirculation. Prolonged use of this position may lead to odours, caused by non-renewal of air, and the formation of condensation on the windows.
Page 208 AUTOMATIC CLIMATE CONTROL: Controls B and C (1/5) Automatic mode The automatic climate control system guarantees comfort in the passen- ger compartment and good visibility (except in the event of extreme condi- tions), while optimising consumption. The system controls the ventilation speed, air distribution, air recirculation, 18 5 and starting and stopping the air condi-...
Page 209 AUTOMATIC CLIMATE CONTROL: Controls B and C (2/5) Note: The air conditioning configura- tion depends on the mode selected in the “Multi-Sense” menu (please refer to the information on “Multi-Sense” in sec- tion 3). 18 5 18 5 The displayed temperature values Varying the ventilation speed Temperature adjustment show a comfort level.
Page 210 AUTOMATIC CLIMATE CONTROL: Controls B and C (3/5) To exit this function, press either: – again button 10; – one of the buttons 14, 15 or 16. 14 15 14 15 Clear View function Press button 10 – the integrated indica- tor light comes on.
Page 211 AUTOMATIC CLIMATE CONTROL: Controls B and C (4/5) Rear screen de-icing/ demisting Press button 6 – the integrated indica- tor light comes on. This function en- ables rapid demisting or de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles).
Page 212 AUTOMATIC CLIMATE CONTROL: Controls B and C (5/5) Automatic usage Press button 8 (a warning light comes on in zone 1). Manual use Press button 9 to force air recirculation. Prolonged use of this position may lead to odours, caused by non-renewal of air, and the formation of condensation on the windows.
Page 213: Fuel Consumption
AIR CONDITIONING: information and operating instructions (1/2) Advice on use Fuel consumption Operating faults In some situations (air conditioning off, You will normally notice an increase in As a general rule, contact your ap- air recirculation activated, ventilation fuel consumption (especially in town) proved dealer in the event of an oper- speed at zero or low etc.), you may when the air conditioning is operating.
Page 214 AIR CONDITIONING: information and operating instructions (2/2) Type of refrigerant fluid Ñ Type of oil in the air condi-  tioning circuit Inflammable product  Consult the driver’s hand-  book Maintenance  Quantity of refrigerant fluid present in the ve- x.xxx kg hicle.
Page 215: Outside Air Quality And Deodorisation Functions
OUTSIDE AIR QUALITY AND DEODORISATION FUNCTION Deodorisation function This reduces unpleasant odours in the passenger compartment. “Deodorization cycle” – ON: helps to reduce the unpleasant odour more quickly in the passenger compartment, – OFF: stop the function. Note: the function is on a timer. It stops automatically after a few minutes.
Page 216: Electric Windows
6. Driver’s responsibility Never leave your vehicle with the RENAULT card or key inside, and never leave a child, adult who is not self-sufficient or a pet, even for a short while. They may pose a risk to themselves or to others by starting the engine or activating equip- ment (such as the gear lever or electric windows).
Page 217 ELECTRIC WINDOWS (2/2) Operating faults One-touch mode This mode works in addition to the ope- In case of a fault when closing a ration of the electric windows described window, the system reverts to normal previously. mode: pull the switch as many times as Briefly press or pull the window switch necessary until the window closes com- fully: the window is fully lowered or...
Page 218: Electric Sunroof
ELECTRIC SUNROOF (1/3) Driver’s responsibility Never leave your vehicle with the RENAULT card inside, and never leave a child who is not self-sufficient or a pet, even for a short while. To slide the curtain 1 To slide the sunroof...
Page 219: Remote Control
Closing the sunroof by remote control If you press the locking button on the card twice in quick succession RENAULT,, the windows and the elec- tric sunroof will close automatically. It is recommended that the user only operates the system when the vehi- cle can be seen clearly and no one is inside.
Page 220 Driver’s responsibility erly arranged and secured and Never leave your vehicle should not interfere with the opera- with the RENAULT card tion of the sunroof. inside, and never leave a Contact an approved dealer for de- child who is not self-sufficient or a tails of possible conversions;...
Page 221: Interior Lighting
INTERIOR LIGHTING (1/2) Map reading lights Courtesy light Note: for vehicles fitted with a naviga- tion system, you can use the multime- Press switch 1 to get: Press switch 3 for: dia screen to deactivate/activate the – permanent lighting; – permanent lighting; courtesy lights which come on when the doors or boot are opened.
Page 222 INTERIOR LIGHTING (2/2) Luggage compartment light 6 The light comes on when the luggage compartment is opened. With the doors properly shut, lock- ing or starting the engine makes the interior lights and the courtesy lights go out. 3.28...
Page 223: Sun Visor/Blinds
SUN VISOR, BLINDS Front sun visor Ticket holder 4 Lower the sun visor 1 on the wind- Can be used to hold motorway toll tick- screen or unclip it and lower it over the ets, maps, etc. side window. Vanity mirror Lift the cover 3.
Page 224: Passenger Compartment Storage/Fittings
PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (1/4) Door pockets 1 Passenger storage compartment It can hold a bottle. Pull handle 2 to open it. The glove box can hold A4-sized docu- ments, a bottle etc. Ensure that no hard, heavy or pointed objects are Nothing should be placed placed in the “open”...
Page 225 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (2/4) Central storage Cup holders 6 compartment 4 A sliding system 5 holds maintains the cups. Central storage compartment 3 When turning corners, accelerating or braking, Ensure that no hard, heavy ensure that the recepta- or pointed objects are cle being held by the cup placed in the “open”...
Page 226 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (3/4) Central storage Grab handle 9 compartment 8 This offers support and can be held when the vehicle is being driven. With the sliding armrest 7 in its rear- most position, raise it. Do not use it for getting into or out of the vehicle.
Page 227 PASSENGER COMPARTMENT STORAGE SPACE AND FITTINGS (4/4) Rear door storage Front seat storage pockets 12 Rear armrest with cup holder compartment 11 Lower armrest 14. Rear central storage compartment 13 Ensure that no hard, heavy When turning corners, or pointed objects are accelerating or braking, placed in the “open”...
Page 228: Accessories Socket
ASHTRAY, CIGARETTE LIGHTER, ACCESSORIES SOCKET (1/2) Cigarette lighter 1 Ashtray 3 With the ignition on, push in cigar It can be housed in either position 2. lighter 1, it will spring back with a click To open, lift the cover. To empty, pull the when it is ready.
Page 229 ASHTRAY, CIGARETTE LIGHTER, ACCESSORIES SOCKET (2/2) Accessories sockets 4 You can use the one of sockets 4. They are provided for connecting ac- cessories approved by our Technical Department. Connect accessories with a maximum power of 120 watts (12 V) only. When several accessory sockets are used at the same time, the total power of the connected...
Page 230: Rear Headrests
REAR HEADRESTS (1/2) Position for using the central Centre seat headrest B To remove a headrest headrest A storage position Raise the headrest as far as it will go, then press button 1 and remove the Raise the headrest as far as possible to Press the button 1 and lower the head- headrest.
Page 231 REAR HEADRESTS (2/2) Storage position for the side headrests Press the button 1 and, depending on the vehicle: – fully lower (movement A) the head- rest 2, or – lower and tilt (movement B) the headrest 3 fully forwards. 3.37...
Page 232: Rear Bench Seat
REAR BENCH SEAT (1/2) The configuration of the two-seat bench with the small seatback B pulled down, does not allow the central seat to be used as it would be impossible to buckle the seat belt (belt buckles inaccessible). When refitting the seat- back, make sure it is cor- rectly locked in place.
Page 233 REAR BENCH SEAT (2/2) Conditions of use – Vehicle stationary; – luggage compartment lid open; – rear seat belts locked. Operating faults If all user conditions have been ful- filled and the folding action still fails to operate, please contact an authorised dealer.
Page 234: Luggage Compartment
“Radiofrequency Remote Control: use” in section 1); – by the locking/unlocking button on card RENAULT (refer to the informa- tion on "Card RENAULT: use in sec- tion 1); – via the external boot lid control; – using the hands-free function;...
Page 235 Disable the “hands-free” Ensure that the RENAULT card is ap- function before you: proximately 1 metre away in the cen- – wash the vehicle in a tral area of the rear bumper of the vehi- roller-type car wash;...
Page 236 15 minutes if the vehicle is approved dealer. unlocked. To reactivate it, use the Note: in very cold weather conditions, unlocking button on the RENAULT Opening the doors manually the automatic opening may not work if card. from the inside the tailgate seals are frozen.
Page 237 LUGGAGE COMPARTMENT: 5-DOOR VERSION To open Opening manually from inside the vehicle Press button 1 and lift the tailgate. Special note: To close If it is impossible to unlock the tailgate, Lower the tailgate using the handles 2 it can be done from inside. inside the tailgate to help you.
Page 238: Rear Parcel Shelf
REAR PARCEL SHELF Removal Unclip the rear parcel shelf 2 and pull it towards you. Unhook the two cords 1 (tailgate side). To refit it, proceed in reverse order to removal. Do not place any heavy or hard object on the parcel shelf.
Page 239: Luggage Compartment Cover
LUGGAGE COMPARTMENT COVER To remove the flexible Removing/refitting the Luggage compartment cover section of the luggage luggage cover 2 storage 2 compartment cover 2 Slide section 3 (movement A) and lift Lift section 4 of the luggage compart- the right-hand side (movement B) of ment floor.
Page 240: Luggage Net
LUGGAGE NET (1/2) Depending on the vehicle, this may be Fitting the luggage net – if using the net for the first time, to used when transporting animals or lug- access the anchorage points 4 lo- behind the front seats gage to isolate them from the passen- cated under the carpet, contact an Inside the vehicle on each side:...
Page 241 LUGGAGE NET (2/2) Fitting the luggage net – fix the net belt hook 9 onto the ancho- ring points 10; behind the rear seats – adjust net strap 8 so that it is taut. The Inside the vehicle on each side: seatbacks must not touch the luggage –...
Page 242 BOOT STORAGE SPACE AND FITTINGS (1/5) Storage under the carpet The false floor can be attached using the hook 4 in the housing 3. To gain access to this, lift the boot carpet 1 using the tab 2. Always place objects being trans- ported so that the heaviest items are resting against the back of the rear bench seat.
Page 243 BOOT STORAGE SPACE AND FITTINGS (2/5) Mobile floor Storage position Separation position (Estate version) This allows for more space to store This enables you to compartmentalise things in the boot. the boot into two separate spaces. It is made up of two independent parts, A and B.
Page 244 BOOT STORAGE SPACE AND FITTINGS (3/5) Lift part C into the vertical position until Storage under floor Lift part A using handle 10 and place it it locks. on the lugs 9. To access it, lift part B of the mobile floor using the handle 8, then place it on part A.
Page 245 BOOT STORAGE SPACE AND FITTINGS (4/5) Bag hooks 11 Storage compartment 12 Storage compartment 13 (Estate version) (four-door version) Maximum weight per hook: 5 kg. To remove the tailboard 14, pull up- wards until it unclips. To replace the tailboard, push it into its housing until you hear a click.
Page 246 BOOT STORAGE SPACE AND FITTINGS (5/5) Anchorage points Attachment points 15 If your vehicle is not equipped with anchorage points, you can get them from an authorised dealer. Always position the heaviest items directly on the floor. Use the lashing points 15 on the boot floor, if these are fitted to the vehicle.
Page 247: Transporting Objects In The Luggage Compartment
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT Always position the objects transported so that the largest surface is against: – The rear bench seatback for normal loads (example A). – The front seatbacks with the rear seatbacks folded down, as is the case for maximum loads (example B).
Page 248: Transporting Objects Towbar
TRANSPORTING OBJECTS towbar Permissible nose weight, maxi- mum permissible towing weight, braked and unbraked: refer to A: 895 mm (5-door version) the information on “Weights” in A: 1120 mm (estate version) Section 6. A: 1127 mm (4-door version) Choice and fitting of towing equipment Maximum weight of towing equip- ment:...
Page 249: Roof Bars
ROOF BARS (1/2) Access to the mounting Vehicles not fitted with longitudinal roof bars points Open the doors to access the mount- ing points 1. For information on the range of equipment adapted to your vehicle, we advise you If original roof bars, ap- to consult an approved Dealer.
Page 250 ROOF BARS (2/2) Precautions during use Handling the tailgate Before handling the tailgate, check the objects and/or accessories (bike rack, roof box, etc.) fitted to the roof bars: these must be correctly positioned and secured, so as not to hinder the opera- tion of the tailgate.
Page 251: Multimedia Equipment
MULTIMEDIA EQUIPMENT (1/2) Multimedia settings Hands-free telephone integrated control 1 Multimedia screen; 2 Steering column controls; For equipped vehicles, use the steering 3 Steering wheel controls; wheel controls 3. 4 Microphone. Using the telephone We remind you of the need to conform to the legislation in force concerning the use Refer to the equipment instructions...
Page 252 MULTIMEDIA EQUIPMENT (2/2) The sockets USB can also recharge ac- cessories with a maximum power rating of 12 Watts (voltage: 5V) per socket, which have been approved by our Technical Department. The JACK socket enables the radio to be used with an auxiliary cable. Multimedia sockets 5 You can use the USB ports or, de- pending on the vehicle, the SD card...
Page 253 Section 4: Maintenance Bonnet ............... . Engine oil level: general information .
Page 254: Bonnet
BONNET (1/2) When working in the engine compartment, ensure that the windscreen wiper stalk To open, pull handle 1, located on the Unlocking the bonnet catch is in the park position. left-hand side of the dashboard. Risk of injury. To unlock, push tab 3 at the same time as opening the bonnet.
Page 255: Closing The Bonnet
BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and guide it down, allowing a 30 cm gap before it is closed, then release it. It will latch automatically under its own weight.
Page 256: Engine Oil Level: General Information
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level be- tween oil changes. However, contact your approved Dealer if more than 0.5 litres is being In order to prevent splashback, it is consumed every 600 miles (1,000 km) recommended that a funnel be used...
Page 257: Engine Oil Level: Topping Up/Filling
ENGINE OIL LEVEL: topping up, filling (1/3) Topping up/Filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the “mini" and the ground and the engine should be cold "maxi"...
Page 258 ENGINE OIL LEVEL: topping up, filling (2/3) Topping up/Filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the “mini" and the ground and the engine should be cold "maxi"...
Page 259: Oil Change
ENGINE OIL LEVEL: topping up, filling OIL CHANGE (3/3)/ Oil change Engine oil grade Service interval: refer Refer to the Maintenance Service Maintenance Service Booklet for your Booklet for your vehicle. vehicle. Oil change capacity Please refer to the maintenance docu- Filling: take care when ment for your vehicle, or contact an au- Consult your approved Dealer at...
Page 260: Levels
LEVELS (1/3) Checking intervals Replacement intervals Check the coolant level regularly Refer to the Maintenance Document for (very severe damage is likely to be your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
Page 261: Brake Fluid Level
LEVELS (2/3) Level 2 Topping up It is normal for the level to drop as After any operation on the hydraulic cir- the linings become worn, but it should cuit, a specialist must replace the fluid. never drop below the “MINI” warning Only use fluids approved by our line.
Page 262: Windscreen Washer Reservoir
LEVELS /FILTERS (3/3) Filters Liquid Windscreen washer fluid. In winter, use The replacement of filter elements (air anti-freeze product. Use products rec- filter, passenger compartment filter, ommended by an authorised dealer. diesel filter, etc.) is scheduled in the maintenance operations for your vehi- Note: do not use pure water (risk of cle.
Page 263: Battery
BATTERY (1/2) Depending on the vehicle, a system continuously checks the battery charge status. If this decreases, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. The message will go off. The charge status of your battery can decrease especially if you use your ve- hicle:...
Page 264 BATTERY (2/2) Replacing the battery As this operation is complex, we advise you to contact an approved Dealer. Label A Observe the indications on the battery: – 2 Naked flames and smoking are for- bidden; – 3 eye protection required; –...
Page 265: Tyre Pressure
TYRE PRESSURE (1/2) Vehicle fitted with a tyre pressure monitoring system If under-inflated (puncture, low pressure  etc.), the warning light lights up on the instrument panel; please refer to «Tyre pressure monitoring system» in Section 2. Label A B: dimension of the tyres fitted to the vehicle.
Page 266 TYRE PRESSURES (2/2) Tyre safety and use of snow chains: Refer to the information on “Tyres” in Section 5 for the servicing conditions and, depending on the version, the use of chains. For your safety, please re- spect the speed limit. When they need to be re- placed, only tyres of the same make, size, type and profile...
Page 267: Bodywork Maintenance
BODYWORK MAINTENANCE (1/3) You should A well-maintained vehicle will last Respect local regulations about wash- longer. It is therefore recommended to ing vehicles (e.g. do not wash your ve- Wash your car frequently, with the maintain the exterior of the vehicle reg- hicle on a public highway).
Page 268 BODYWORK MAINTENANCE (2/3) What you should not do Wash the vehicle in bright sunlight or Degrease or clean using freezing temperatures. high-pressure cleaning Do not scrape off mud or dirt without equipment or by spray- pre-wetting. ing on products not ap- Allow dirt to accumulate on the exterior.
Page 269 BODYWORK MAINTENANCE (3/3) Vehicles with a matte paint Using a roller type car wash Cleaning the headlights finish Return the windscreen wiper stalk to As the headlights are made of plastic the Park position (refer to the informa- “glass”, use a soft cloth or cotton wool This type of paint requires certain pre- tion on the “Windscreen washer, wiper”...
Page 270: Interior Trim Maintenance
INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, etc.) larly.
Page 271 INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in Position objects such as deodorants, the vehicle scents etc. near air vents as this could damage your dashboard trim. If you need to remove equipment in order to clean the passenger com- partment (for example, mats), always ensure that they are correctly refitted and are the right way around (the driv-...
Page 272 4.20...
Page 273 RENAULT card: battery ........
Page 274: Puncture/Emergency Spare Wheel
PUNCTURE, EMERGENCY SPARE WHEEL (1/2) In case of puncture Depending on the vehicle, a tyre infla- tion kit or emergency spare wheel is provided (refer to the following pages). Special note The Tyre Pressure Monitor function does not check the emergency spare wheel (the wheel replaced by the emer- gency spare wheel disappears from the instrument panel display).
Page 275 PUNCTURE, EMERGENCY SPARE WHEEL (2/2) Emergency spare wheel 3 Vehicle not fitted with a Vehicle fitted with a subwoofer subwoofer This is located in the luggage compart- ment. To access it: To access it: – open the boot; – open the boot; –...
Page 276 TYRE PRESSURE KIT (1/3) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
Page 277 TYRE PRESSURE KIT (2/3) With the engine running and the Note: While the container empties parking brake applied, (approx. 30 secs), the pressure gauge 6 briefly shows pressure up to – Connect the compressor hose 4 to 6 bar, then the pressure drops. the container inlet 9;...
Page 278 TYRE PRESSURE KIT (3/3) Precautions when using the Once the tyre is correctly inflated, remove the kit: slowly unscrew the in- flation end piece 3 to prevent any prod- The kit should not be operated for more uct spatter and store the container in than 15 consecutive minutes.
Page 279: Tools
TOOLS Hubcap tool 4 This tool is used to remove the wheel trims. Screw guide 5 For tightening/loosening wheel bolts on vehicles fitted with alloy wheels Towing hitch 6 Refer to the information on “Towing” in Section 5. Wheelbrace 7 Locks or unlocks the wheel bolts and Tool kit storage Jack 2...
Page 280 HUBCAP Remove using the hubcap tool 1 (lo- cated in the tool kit) by connecting the hook in the recess provided next to the valve 2 (to attach the metal clip). To refit it, align it with valve 2. Push the retaining hooks in fully, starting with side A near the valve, followed by B and C, finishing at D opposite the valve.
Page 281: Changing A Wheel
CHANGING A WHEEL (1/2) Vehicles equipped with a jack Place the jack 3 horizontally; the jack head must be lined up with the sill clos- and wheelbrace est to the wheel concerned, as shown If necessary, remove the wheel trim. by an arrow 1.
Page 282 CHANGING A WHEEL (2/2) Undo the bolts and take off the wheel. Fit the emergency spare wheel onto the hub and rotate it until the mounting holes in the wheel coincide with those of the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel.
Page 283: Tyres (Tyre And Wheel Safety, Use In Winter)
TYRES (1/3) The tyres are the only contact between When the tread has worn down to the the vehicle and the road, so it is essen- wear warning strips, these strips will tial to keep them in good condition. become visible 2: it is then necessary to replace your tyres because the tread You must make sure that your tyres rubber is now only 1.6 mm deep at...
Page 284: Tyre Pressures
TYRES (2/3) Tyre pressures The pressures should be checked cold: Vehicle fitted with a tyre pressure ignore higher pressures which may be monitoring system Adhere to the tyre pressures (including reached in hot weather or following a If under-inflated (puncture, low pressure the emergency spare wheel).
Page 285 TYRES (3/3) Fitting new tyres Use in winter Studded tyres This type of equipment may only be Snow or Winter tyres used for a limited period and as laid We would recommend that these be down by local legislation. It is neces- fitted to all four wheels to ensure that For your safety, please re- sary to observe the speed specified by...
Page 286: Headlights (Changing Bulbs)
FRONT HEADLIGHTS: replacing the bulbs (1/2) Any operation on (or modi- fication to) the electrical system must be performed by an approved dealer since an incorrect connection might damage the electrical equipment (harness, components and in partic- ular the alternator). In addition, your Dealer has all the parts required for fitting these units.
Page 287 FRONT HEADLIGHTS: replacing the bulbs (2/2) Daytime running lights and side lights 5 Please see an authorised dealer. Front fog lights 7 – Access the bulb holder via the un- derneath of the vehicle; – unclip the access flap 8; –...
Page 288 REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (1/9) 5-door version Access to the bulb holders 6 Brake light 1 and 7 Turn bulb holder 6 a quarter of a turn Side light 3 and take out the bulb. Open the boot, remove the cover 4 to access the screw 5 and undo it.
Page 289: Rear Lights And Side Lights (Replacing Bulbs)
REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (2/9) Reversing light Turn bulb holder 9 a quarter of a turn High level brake light 10 and take out the bulb. From the boot, unclip the cover on the Consult an approved dealer. Bulb type: W16W.
Page 290 REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (3/9) Number plate lights 12 Side repeaters 13 and welcome lighting 14 – Unclip the light 12 using a tool such as a flat-blade screwdriver; The wing mirror needs to be removed; consult an authorised dealer.
Page 291 REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (4/9) Estate version Access to the bulb-holder 6 Direction indicator light 2 Open the luggage compartment lid, Turn bulb holder 6 a quarter of a turn Brake light 1 remove the cover 4 to access the two and take out the bulb.
Page 292 REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (5/9) Reversing light Turn bulb holder 8 a quarter of a turn Rear fog light 9 and take out the bulb. From the boot, unclip the cover on the Unclip the flap located under the rear Bulb type: W16W.
Page 293 REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (6/9) Number plate lights 12 Side repeaters 13 and welcome lighting 14 – Unclip the light 12 using a tool such as a flat-blade screwdriver; The wing mirror needs to be removed; consult an authorised dealer.
Page 294 REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (7/9) 4-door version Access to the bulb holders 6 Brake light 1 and 7 Turn bulb holder 6 a quarter of a turn Side light 3 and take out the bulb. Open the boot, remove the cover 4 to access the screw 5 and undo it.
Page 295 REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (8/9) Reversing light Turn bulb holder 9 a quarter of a turn High level brake light 10 and take out the bulb. From the boot, unclip the cover on the Consult an approved dealer. Bulb type: W16W.
Page 296 REAR LIGHTS AND SIDE LIGHTS: replacing the bulbs (9/9) Number plate lights with LED number plate lights 13 Side repeaters 14 and conventional bulbs 12 (depending on vehicle) welcome lighting 15 (depending on vehicle) Consult an approved dealer The wing mirror needs to be removed; –...
Page 297: Interior Lighting: Changing Bulbs
INTERIOR LIGHTING: changing bulbs (1/3) Ambient lighting Please consult an authorised dealer. Map reading lights 1 Courtesy light 2 Please consult an authorised dealer. Please consult an authorised dealer. 5.25...
Page 298 INTERIOR LIGHTING: changing bulbs (2/3) Glove box light 3 Luggage compartment light 4 (four-door version) Unclip the light by pressing the tab with a flat-blade screwdriver or simi- Unclip the light by pressing the tab with lar. Remove the light by the rear whilst a flat-blade screwdriver or similar.
Page 299 INTERIOR LIGHTING: changing bulbs (3/3) Luggage compartment light 6 (five-seater and estate versions) Unclip the light by pressing the tab with a flat-blade screwdriver or similar. Disconnect the light. Access the bulb. Bulb type: W5W. The bulbs are under pres- sure and can break when replaced.
Page 300: Fuses
FUSES (1/2) Use the fuse allocation label on the back of flap A to identify the fuses. Certain fuses should only be replaced by a qualified professional. These fuses are not listed on the label. Only change the fuses represented on the label.
Page 301 FUSES (2/2) Allocation of fuses (the presence of certain fuses depends on the vehicle equipment level) Symbol Allocation Symbol Allocation Windscreen washer Towbar socket Ý ë Not used  Not used Front cigarette lighter, front and rear second row Diagnostic socket, audio alarm Æ...
Page 302: Connecting A Battery Charger
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (cour- The battery charger must be com- tesy lights, etc.) are switched off patible with a battery with nominal before disconnecting or reconnect- voltage of 12 volts.
Page 303 BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
Page 304: Battery
RENAULT lock/unlock the vehicle (please refer to Note: it is not advisable to touch the card: the information on “Locking/unlocking...
Page 305: Radio Frequency Remote Control: Batteries
RADIO FREQUENCY REMOTE CONTROL: batteries Replacing the battery Note: It is not advisable to touch the Operating faults electronic circuit in the key cover when Open the case at slot 1 using a flat- If the battery is too weak to ensure cor- replacing the battery.
Page 306: Accessories
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 Watts only.
Page 307 WIPER BLADES: REPLACEMENT (1/2) Replacing windscreen wiper – In frosty weather, make blades 1 sure that the wiper blades are not stuck by ice (to With the ignition on and engine avoid the risk of the motor switched off, lower the windscreen overheating).
Page 308 WIPER BLADES: REPLACEMENT (2/2) To refit To refit the wiper blade, proceed in re- verse order to removal. Make sure that the blade is correctly locked in position. Rear screen wiper blade 4 Stalk in stop position (deactivated): – Lift wiper arm 6; –...
Page 309: Towing: Breakdown
Transport the vehicle on a trailer or tow RENAULT card on you, press the it with the front wheels off the ground. engine start button for 2 seconds. Reposition the lever to neutral (posi-...
Page 310 TOWING: breakdown recovery (2/2) Use the towing eye 5 only (please see “Tools” in Section 5). – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed Only use the front 3 and rear 6 towing Access to towing points must be able to brake.
Page 311: Operating Faults
Dealer as soon as possible. Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or Card battery is flat. Replace the battery or have it replaced. unlock the doors. You can still lock/unlock and start your vehicle (refer to the information on “Locking/unlocking the doors”...
Page 312 OPERATING FAULTS (2/7) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. Using the remote control POSSIBLE CAUSES ACTION REQUIRED The remote control does not lock or The remote control battery is flat.
Page 313 Starting conditions are not Please refer to the information on “Starting, stopping fulfilled. the engine” in Section 2. The RENAULT card does Please refer to the information on “Starting, stopping not work. the engine” in Section 2. The engine cannot be switched off.
Page 314 OPERATING FAULTS (4/7) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pres- Check the tyre pressures: if this is not the sures, incorrectly balanced or dam- problem, have them checked by an ap- aged. proved Dealer.
Page 315 OPERATING FAULTS (5/7) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Drive carefully at reduced speed, be aware of the level of force in the steering wheel Fault with the electric assistance needed to turn the wheels. Consult an ap- motor.
Page 316 OPERATING FAULTS (6/7) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse or have it replaced; refer to the information on “Fuses”...
Page 317 OPERATING FAULTS (7/7) Electrical equipment POSSIBLE CAUSES WHAT TO DO Traces of condensation in the lights Traces of condensation may be a nat- and headlights. ural phenomenon caused by varia- tions in temperature and humidity. In this case, the traces will disappear slowly once the lights are switched The front seat belt reminder light An object is stuck between the floor...
Page 318 5.46...
Page 319 Section 6: Technical specifications Vehicle identification plates ............Engine identification plates .
Page 320: Vehicle Identification Plates
VEHICLE IDENTIFICATION PLATES The information shown on the ve- 4 MMAC (Maximum permissible hicle identification plate should be all-up weight). quoted on all correspondence or 5 MTR (Gross train weight: vehicle orders. fully loaded, with trailer). 6 MMTA (Maximum Permissible The presence and location of the in- Weight) front axle.
Page 321: Engine Identification Plates
ENGINE IDENTIFICATION PLATES (1/2) Please quote the information on the engine plate or label A in all corre- spondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
Page 322 ENGINE IDENTIFICATION PLATES (2/2) Please quote the information on the engine plate or label A in all corre- spondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
Page 323: Dimensions
DIMENSIONS (in metres) (1/3) Five-door version 0,921 2,670 0,768 1,574 to 1,596 4,359 1,446* 1,565 to 1,599 2,058 * Unladen...
Page 324 DIMENSIONS (in metres) (2/3) Estate versions 0,921 2,712 0,993 1,574 to 1,596 4,626 1,449* 1,565 to 1,599 2,058 * Unladen...
Page 325 DIMENSIONS (in metres) (3/3) Four-door version 0,921 2,711 0,998 1,577 to 1,583 4,630 1,443* 1,583 to 1,587 2,058 * Unladen...
Page 326: Engine Specifications
ENGINE SPECIFICATIONS Versions 2.0 16V 1.2 TCe 1.6 16V 1.6 TCe 1.5 dCi 1.6 dCi Engine type H5F Turbo M5M Turbo (see engine plate) Cubic capacity (cc) 1995 1197 1598 1618 1 461 1598 Diesel The label located in the fuel filler Type of fuel It is essential that you use unleaded petrol of the octane rating flap indicates authorised fuels.
Page 327: Weights
WEIGHTS (in kg) The weights indicated are for a basic vehicle without options: they may vary depending on your vehicle’s equipment. Consult an approved Dealer. Five door Estate Four-door Maximum permissible all-up weight (MMAC) Weights are indicated on the vehicle identification plate (refer to Maximum permissible all-up weight (MMTA) the information on “Vehicle identification plates”...
Page 328: Replacement Parts And Repairs
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
Page 329: Service Sheets
SERVICE SHEETS (1/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 330 SERVICE SHEETS (2/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 331 SERVICE SHEETS (3/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 332 SERVICE SHEETS (4/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 333 SERVICE SHEETS (5/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 334 SERVICE SHEETS (6/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 335: Anticorrosion Check
ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
Page 336 ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...
Page 337 ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.19...
Page 338 ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.20...
Page 339 ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.21...
Page 340 6.22...
Page 341 ALPHABETICAL INDEX (1/6) bulbs ABS ...............2.30 → 2.39 changing ........5.14 → 5.27, 5.26 – 5.27 accessories................ 5.34 accessories socket ........3.34 – 3.35, 3.58 catalytic converter........... 2.14 – 2.15 adaptive cruise control...........2.61 → 2.67 central door locking ....1.2 – 1.3, 1.5, 1.13 → 1.16, 1.20 additional methods of restraint .....1.30 →...
Page 342 ALPHABETICAL INDEX (2/6) windscreen ............3.6 → 3.13 exterior air quality .............. 3.21 deodourisation ..............3.21 external temperature ............1.85 dimensions ..............6.5 → 6.7 display ........1.60 → 1.71, 1.68 → 1.71, 3.57 fatigue detection warning........2.49 – 2.50 doors..............1.17 → 1.20 doors/tailgate ..............
Page 343: Maintenance
ALPHABETICAL INDEX (3/6) interior trim gear lever................2.16 maintenance ............. 4.18 – 4.19 grab handle................ 3.32 Isofix ..............1.49 → 1.51 »hands-free» card: battery ..........5.32 jack ..................5.7 handbrake..............2.16 → 2.19 keys ................1.2 → 1.5 handsfree..........1.8 → 1.10, 3.41 – 3.42 hands-free telephone integrated control ....
Page 344 ............... 5.33 remote control door locking unit ........1.2 → 1.4 navigation ............... 3.57 – 3.58 RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.20 navigation system ........... 3.57 – 3.58 RENAULT card battery ................5.32 oil change ..............4.4, 4.7 use ..............1.6 →...
Page 345: Technical Specifications
ALPHABETICAL INDEX (5/6) tanks and reservoirs: safety distance warning .......... 2.47 – 2.48 windscreen washer ............4.10 safety distances ............2.47 – 2.48 technical specifications ..........6.5 → 6.10 screen telephone ..............3.57 – 3.58 fold-away screen ............1.70 temperature regulation ..........3.9 → 3.20 navigation display ......
Page 346: Alphabetical Index
ALPHABETICAL INDEX (6/6) warning lights........1.60 → 1.65, 1.72 → 1.81 washing ..............4.15 → 4.17 weights ................6.9 wheelbrace ................5.7 wheels (safety) ............5.11 → 5.13 windscreen de-icing/demisting ......... 3.11, 3.16 windscreen washer ..1.96 → 1.101, 1.100, 1.102 – 1.103, 4.10 windscreen washer/wiper ........1.96 →...
Page 348 à999106195Rê ú ò ä ZB RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Renault MEGANE User Manual

Section 1: Getting to Know Your Vehicle

Section 2: Driving

Section 3: Your Comfort

Section 4: Maintenance

Section 5: Practical Advice

Quick Links

Chapters

Need help?

Questions and answers

Related Manuals for Renault MEGANE

Summary of Contents for Renault MEGANE

Table of Contents