Related Manuals for GreenWorks 2800100
Summary of Contents for GreenWorks 2800100
- Page 1 10" LITHIUM CULTIVATOR 2800100 218549 Owner’s Manual TOLL-FREE HELPLINE: 1-888-90WORKS (888.909.6757) Read all safety rules and instructions carefully before operating this tool.
-
Page 2: Table Of Contents
CONTENTS Contents ..........................2 ........................2 Safety Information ......................3 - 6 Symbols ..........................7- 8 Electrical ......................... 9 -10 Know Your Electric Cultivator....................11 Assembly ........................12-15 Maintenance ....................... 1 6 - 1 7 & . r e .. -
Page 3: Safety Information
SAFETY INFORMATION READ AND UNDERSTAND ALL INSTRUCTIONS. personal injury. WARNING: when using electric gardening appliances,basic safty precautions should always be followed to reduce the risk of fire, elctric shock and personal injury including the following. READ THESE INSTRUCTIONS BEFORE USING THE ELECTRIC CULTIVATOR •... -
Page 4: Specific Safety Rules
SAFETY INFORMATION • Remove the battery pack and verify that all moving parts have come to a complete stop before cleaning, repairing, or inspecting the tool. • Never spray water directly into the motor compartment. • Service on the tiller/cultivator must be performed by qualified repair personnel only. Service or maintenance that is performed by unqualified personnel could result in injury to the user or damage to the product. - Page 5 BATTERY & CHARGER C A U T I O N Use only greenworks approved replacement batteries, other batteries may cause injury or damage to the unit. Use with GREENWORKS 40V battery (#29652/29662) . BATTERY SAFETY RULES •...
- Page 6 SAFETY INFORMATION other possible serious injuries. • Keep battery pack dry, clean, and free from oil and grease. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean battery pack. PROPER CARE FOR BATTERY Off-season storage To obtain the longest possible battery life, we suggest the following: •...
-
Page 7: Symbols
SYMBOLS Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper inter-pretation of these symbols will allow you to operate the product better and safer. SYMBOL NAME DESIGNATION/EXPLANATION Volts Voltage Amperes Current Hertz Frequency (cycles per second) -
Page 8: Symbols
SYMBOLS The following signal words and meanings are intended to explain the levels of risk associated with this product. SYMBOL SIGNAL MEANING DANGER Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. WARNING Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. -
Page 9: Know Your Electric Cultivator
KNOW YOUR CULTIVATOR HANDLE BAR SAFETY LOCK-OUT BUTTON SLIDE BOLT HITCH PIN TINE SHIELD WHEEL ASSEMBLY OUTER TINE HITCH PIN INNER TINE Fig. 2 Read this operator’s manual and safety rules before operating your cultivator. Compare the illutration in Fig.2 to your cultivator in order to familiarize yourself with the location of various controls and adjustments. -
Page 10: Assembly
ASSEMBLY UNPACKING This product requires assembly. • Carefully remove the product and any accessories from the box. Make sure that all items listed in the packing list are included. • Inspect the tool carefully to verify no breakage or damage occurred during shipping. •... - Page 11 ASSEMBLY ASSEMBLING THE HANDLEBAR (See Figure. 3) • Align the holes on the middle with the holes on the lower handles. Insert the bolts, and tighten them using the wing nuts provided. • Fold the handle base on the Fig.4 - 4.1 Step1: Release the wing nuts UPPER Step2: Rotate the upper handle...
- Page 12 ASSEMBLY ASSEMBLING THE WHEELS (See Figure. 5) The wheels are used to control the depth of operation. To adjust the height of the cultivator. 1. Remove the battery from the unit. 2. Place cultivator in a stable position as shown in Fig. 5 3.
- Page 13 ASSEMBLY INSTALLING THE TINES (See Figure 6) The cultivator comes with four tines—For correct operation of the unit, the tines must be installedin the correct order. The cultivator may be used with four tines or two tines. • Disconnect from power source. •...
- Page 14 ASSEMBLY TINES INSTALLED CORRECTLY (See Figure. 7) NOTE: tine blades should point towards the ground (Fig. 7). NOTE: The tiller will not operate properly if the tines are not installed correctly. If there is a problem with the cultivating operation of the tiller, check the tines for proper positioning. NOTE: The directional arrow that is displayed on each tine should point toward the front.
- Page 15 OPERATION W A R N I N G Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a W A R N I N G Always wear safety goggles or safety glasses with side shields when operating tools. Failure to do so could result in objects being thrown into your eyes, resulting in possible serious injury.
- Page 16 OPERATION PREPARING THE SEED BED The cultivator can be used to break up garden soil and prepare a seedbed for planting. Plan ahead to leave enough room between the seed rows to allow for machine cultivating after the plants have grown. TILLING SOD: Tilling sod into the soil is not recommended.
-
Page 17: Maintenance
MAINTENANCE W A R N I N G WHEN SERVICING, USE ONLY IDENTICAL REPLACEMENT PARTS. USE OF ANY OTHER PARTS MAY CREATE A HAZARD OR CAUSE PRODUCT DAMAGE. W A R N I N G ALWAYS WEAR SAFETY GOGGLES OR SAFETY GLASSES WITH SIDE SHIELDS DURING PRODUCT OPERATION. - Page 18 BATTERY CHARGER CHARGING PROCEDURE (See Figure 1 ) NOTE: The battery is not shipped fully charged. It is recommended to fully charge before first use to ensure that maximum run time can be achieved. This lithium-ion battery will not develop a memory and may be charged at any time.
- Page 19 BATTERY CHARGER CHARGER MAINTENANCE • Keep the charger clean and clear of debris. Do not allow foreign material into the recessed cavity or on the contacts. Wipe with a dry cloth. Do not use solvents, water, or place in wet conditions.
-
Page 20: Troubleshooting
TROUBLESHOOTING PROBLEM CAUSE REMEDY Motor fails to start when The battery is not inserted in Insert the battery into unit. switch trigger is depressed. or connection is loose. Motor runs but tines do not Gear train failure. Take unit to authorized ser- move. -
Page 21: Warranty
(4) years against defects in materials, parts or workmanship. GREENWORKS™, at its own discretion will repair or replace any and all parts found to be defective, through normal use, free of charge to the customer. This warranty is valid only for... -
Page 22: Exploded View
EXPLODED VIEW... -
Page 23: Parts List
PARTS LIST ITEM # PART NO. DESCRIPTION 31115281 BLADE BLADE 31114281 NUTS M8 32208261 BOLT 32203289 GEAR BOX ASSY’ 31102289-1 BLADE 31103281 WASHER 34901282-1 BLADE 31102281 33210289 3220436 BOLT SCREW 3220505 LEFT HOUSING 34107289 COVER 33301289 WHEEL CAP 34106488 3290135 WASHER 3220898 6”... - Page 24 TOLL-FREE HELPLINE: 1-888-90WORKS (888.909.6757) Rev: 03 (07-30-2015) Printed in China on 100% Recycled Paper...
Need help?
Do you have a question about the 2800100 and is the answer not in the manual?
Questions and answers