Viavi HST-3000 User Manual
  1. Manuals
  2. Brands
  3. Viavi Manuals
  4. Test Equipment
  5. HST-3000
  6. User manual

Viavi HST-3000 User Manual

Base unit
Hide thumbs Also See for HST-3000:
Table of Contents

Advertisement

Quick Links

Download this manual
HST-3000
Base Unit
User's Guide

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the HST-3000 and is the answer not in the manual?

Questions and answers

Related Manuals for Viavi HST-3000

Summary of Contents for Viavi HST-3000

  • Page 1 HST-3000 Base Unit User’s Guide...
  • Page 3 HST-3000 Base Unit User’s Guide Viavi Solutions 1-844-GO-VIAVI www.viavisolutions.com...
  • Page 4 Copyright © Copyright 2/17/16 Viavi Solutions, Inc. All rights reserved. The Viavi, logo is a trademark of Viavi Solutions, Inc. (“Viavi”). All other trademarks and registered trademarks are the prop- erty of their respective owners. No part of this guide may be reproduced, transmitted electronically, or otherwise distrib- uted without written permission of the publisher.
  • Page 5 In the European Union, all equip- ment and batteries purchased from Viavi after 2005-08-13 can be returned for disposal at the end of its useful life. Viavi will ensure that all waste equipment and batteries returned are...
  • Page 6 HST-3000 Base Unit User’s Guide...

  • Page 7: Table Of Contents

    HST-3000 Overview About the HST-3000......2 Base unit features ....... 3 What’s new in this release .
  • Page 8 Turning the unit on and off ..... . . 28 Checking the battery ......29 HST-3000 Base Unit User’s Guide...
  • Page 9 Configuring international settings....40 Accessing a remote HST-3000 ....41 Remote Operation.
  • Page 10 Specifying FTP/HTTP settings ....102 Specifying general settings ....103 viii HST-3000 Base Unit User’s Guide...
  • Page 11 Event log ........132 HST-3000 Base Unit User’s Guide...
  • Page 12 VT100 cabling ....... . . 160 HST-3000 Base Unit User’s Guide...
  • Page 13 Environmental specifications....194 Power specifications......195 Index HST-3000 Base Unit User’s Guide...
  • Page 14 Contents HST-3000 Base Unit User’s Guide...
  • Page 15 “Purpose and scope” on page xiv – “Assumptions” on page xiv – “Terminology” on page xiv – “HST-3000 Base Unit User’s Guide” on page xv – “Application-orientated user guides” on page xv – “Safety and compliance information” on page xv –...

  • Page 16: About This Guide

    Assumptions This guide is intended for novice, intermediate, and experi- enced users who want to use the HST-3000 effectively and efficiently. We are assuming that you have basic computer experience and are familiar with basic telecommunication concepts, terminology, and safety.

  • Page 17: Hst-3000 Base Unit User's Guide

    HST-3000 Base Unit User’s Guide HST-3000 Base Unit User’s Guide This is the user’s guide for the HST-3000 base unit. It contains overall information relating to device and general functions such as using the unit with a keyboard, peripheral support, battery charging, saving and printing results, and managing files.

  • Page 18: Conventions

    Typographical conventions Description Example User interface actions and Press the OK key. buttons or switches you have to press appear in this type- face. Code and output messages All results okay appear in this typeface. HST-3000 Base Unit User’s Guide...
  • Page 19 Start > Program Files. menu. Table 4 Symbol conventions This symbol represents a general hazard. This symbol represents a risk of electrical shock. This symbol represents a risk of explosion xvii HST-3000 Base Unit User’s Guide...
  • Page 20 WARNING Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. CAUTION Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. xviii HST-3000 Base Unit User’s Guide...

  • Page 21: Hst-3000 Overview

    HST-3000 Overview Chapter 1 This chapter provides a general description of the HST-3000. Topics discussed in this chapter include the following: – “About the HST-3000” on page 2 – “Base unit features” on page 3 – “What’s new in this release” on page 4 –...

  • Page 22: About The Hst-3000

    Modules can be changed in the field and are designed for plug-and-test simplicity and ease of use. When a SIM is plugged into the HST-3000 it is ready to use in seconds and contains the setup and results information from the last time that SIM was used.

  • Page 23: Base Unit Features

    The web browser allows viewing a web page to verify internet access. Viavi can be contracted to customize and install scripts as well as other back office interoperability. CAUTION: BATTERY INTERFERENCE Do not place a property label on the HST under the battery.

  • Page 24: What's New In This Release

    The following sections list the options available for the HST-3000 base unit. NOTE: For additional information about HST-3000 options, SIMs, and services, contact your local Viavi representative or con- tact Viavi through the company web site, www.viavisolu- tions.com. HST-3000 Base Unit User’s Guide...

  • Page 25: Base Unit Options

    Chapter 1 HST-3000 Overview Options Base unit The HST-3000 base unit is factory configurable with or without options copper testing. Table 1 describes the available base units. Table 1 Base unit options Base Unit Description Part Number Options HST-3000 Base unit with Ethernet con-...
  • Page 26 Options Table 2 Software options (Continued) Option Description Part Number Remote Operation Allows you to access the HST-3000 HST3000-REMOP user interface from a PC through a virtual network connection (VNC) over Ethernet. Scripting Allows you to run scripts that auto- HST3000-SCRIPT mate test operations.

  • Page 27: Sims

    10/100 Mbps electrical Ethernet services, and, optionally, 1 GigE or 100 Mbps optical Ethernet services. Viavi offers a wide variety of SIMS and software options; contact your local Viavi representative for details. The regional sales offices are listed on the back cover of this guide.
  • Page 28 Chapter 1 HST-3000 Overview Options HST-3000 Base Unit User’s Guide...

  • Page 29: Quick Tour

    – “Using the front panel” on page 10 – “Using the top panel” on page 14 – “Using the bottom panel” on page 15 – “Working with the user interface” on page 18 HST-3000 Base Unit User’s Guide...

  • Page 30: Using The Front Panel

    Chapter 2 Quick Tour Using the front panel Using the front panel The controls and indicators on the HST-3000 front panel, shown in Figure 3, are used to operate the unit, set up tests, and view data. Status LEDs Soft keys...

  • Page 31: Status Leds

    The OK key is used to accept a change or go to the next menu. Arrow keys The arrow keys are used to navigate the menu selections; for example, to move to a different selection, to scroll to another tab, and so on. HST-3000 Base Unit User’s Guide...

  • Page 32: Navigation Keys

    The second function key, sometimes called the shift key, is function key used to give the numeric keys an extra function. An arrow icon appears on the screen when you press the second function key. The icon located under each key indicates the second HST-3000 Base Unit User’s Guide...

  • Page 33: Power Key

    Backlight. Found under the pound (#) key, toggles the display backlight on and off. Power key The power key turns the unit power on or off. Press and hold for ½ second to turn on or off. HST-3000 Base Unit User’s Guide...

  • Page 34: Using The Top Panel

    Chapter 2 Quick Tour Using the top panel Using the top panel The HST-3000 top panel is used to connect an audio headset or to connect to an external output device. Figure 4 shows the top panel, with a copper testing SIM attached.

  • Page 35: Headset Connector

    The Headset connector is used to connect a 2.54mm micro- connector phone/speaker audio headset. USB connector The USB host connector is used to connect the HST-3000 to a USB keyboard or USB mouse. Ethernet The Ethernet connector is used to connect a 10/100 BaseT connector Ethernet crossover cable for software upgrades.

  • Page 36: Bottom Panel With The Ez Battery

    Speaker Charger connector Serial connector Figure 5 HST-3000 bottom panel with EZ battery The charger connector is used to connect the AC adapter. You can also connect the optional cigarette lighter adapter. CAUTION: INSTRUMENT DAMAGE Using the incorrect adapter can damage the battery. Use only the AC Adapter/Charger supplied with the product.

  • Page 37: Bottom Panel With The 14Pin Battery

    Figure Charger/Serial Connector Speaker Figure 6 HST-3000 bottom panel with 14pin battery The charger/serial connector is used to connect the following items to the HST: – AC power adapter – Cables for use with the optional VT100 feature –...

  • Page 38: Working With The User Interface

    Working with the user interface Working with the user interface The user interface of the HST-3000 is designed to be intuitive and easy to use. Using the LCD and keypad, you can perform tasks such as viewing test results, setting up the unit, and configuring test parameters.

  • Page 39: Status Icons

    The quick help line gives a short description for navigating the menu or quick instructions for a task. Menu items and The menu item and description area present a highlighted descriptions menu item and gives a short description of the item. HST-3000 Base Unit User’s Guide...

  • Page 40: Soft Keys

    (for example, 2, A, B, C). Keypad:abc Repeated key presses cycle through the number and lower case letters for that key (for example, 2, a, b, c). HST-3000 Base Unit User’s Guide...
  • Page 41 Use the left or right arrow key to navigate among the charac- ters. Entering menus To enter the various menus available on the HST-3000, use the second function keys, navigation keys, arrow keys, or press the corresponding menu item number on the keypad (fastest).
  • Page 42 Home to return to the measurements screen. NOTE: Since there are multiple ways to enter, move through, and select menu items, the fastest method is used in the proce- dures throughout this manual. HST-3000 Base Unit User’s Guide...

  • Page 43: Getting Started

    Getting Started Chapter 3 This chapter describes how to setup the base functions of the HST-3000. Topics discussed in this chapter include the following: – “Safety instructions” on page 24 – “Removing and attaching a SIM” on page 24 –...

  • Page 44: Safety Instructions

    Chapter 3 Getting Started Safety instructions Safety instructions The HST-3000 should only be used for the purpose and under the conditions for which it is intended. Operation outside these conditions may be dangerous or may damage the instrument. For additional safety information, refer to the printed safety document or the electronic safety document located on the HST user documentation CD-ROM.

  • Page 45: Removing A Sim

    Back of the HST-3000 The following procedure describes how to remove a SIM. To remove the module 1 Loosen the ¼-turn fastener using a screwdriver. 2 Carefully lift the SIM to remove. The module is removed. HST-3000 Base Unit User’s Guide...

  • Page 46: Attaching A Sim

    Some SIMs are larger than others. For most SIMs, the tab will be on the top edge of the SIM; for others, it is near the middle of the SIM. 2 Turn the base unit so you are looking at it from the side. HST-3000 Base Unit User’s Guide...
  • Page 47 Inserting the SIM tab You should be able to feel that the SIM tab is inserted correctly, as you cannot push the SIM forward. Figure 10 shows an incorrect insertion. Tab not inserted Figure 10 Incorrect SIM attachment HST-3000 Base Unit User’s Guide...

  • Page 48: Turning The Unit On And Off

    The module is connected. Turning the unit on and off Before using the HST-3000, you should turn on the unit. To turn on the HST-3000 – Press and hold the power key for about ½ a second.

  • Page 49: Checking The Battery

    To check the battery level 1 Press the System navigation key. 2 Press the USER soft key. The User Preferences menu appears. 3 Select Power Management. The Power Management Settings menu appears. 4 View the Battery Level. HST-3000 Base Unit User’s Guide...
  • Page 50 Chapter 3 Getting Started Checking the battery HST-3000 Base Unit User’s Guide...

  • Page 51: Instrument Settings And User Preferences

    “Transferring files using Bluetooth” on page 38 – “Specifying FTP settings” on page 39 – “Configuring international settings” on page 40 – “Accessing a remote HST-3000” on page 41 – “Installing X.509 Certificates” on page 53 – “Launching an application automatically” on page 53 –...

  • Page 52: Changing Instrument Settings

    To access the Instrument Setup menu 1 Press the System navigation key. 2 Press the INSTRUMENT soft key. The Instrument Setup menu appears. HST-3000 Base Unit User’s Guide...

  • Page 53: Setting The Date And Time

    Setting the date and time Setting the date and time The first selection on the Instrument Setup menu is Date and Time. The HST-3000 has an internal clock that you can set to provide accurate time stamps for test results. NOTE:...

  • Page 54: Changing The Date And Time Format

    The Date and Time Settings menu appears. 3 Select Date Format. 4 Select one of the following formats: – DD/MM/YYY – MM/DD/YYY The date format is set. The following procedure describes how to change the time format. HST-3000 Base Unit User’s Guide...

  • Page 55: Changing Port Settings

    The Serial Settings menu appears. 4 Press 1 then select the Serial Speed. 5 Press 2 then select the Parity. 6 Press 2 then select the Data Bits. 7 Press 2 then select the Stop Bits. HST-3000 Base Unit User’s Guide...

  • Page 56: Ethernet Port

    6 Press 4 then enter the Net Mask address. 7 Press 5 then enter the Gateway address. 8 Press 6 then enter the address of the DNS server. 9 Press 7 then select the Media Type. The ethernet port settings are changed. HST-3000 Base Unit User’s Guide...

  • Page 57: Viewing Usb Devices

    Any USB device connected to and recognized by the HST-3000 is listed. NOTE: The HST can recognize up to two changes of the USB device. You must turn the unit off then back on for the HST to recognize another change. HST-3000 Base Unit User’s Guide...

  • Page 58: Transferring Files Using Bluetooth

    1 Press the System navigation key. 2 Press the INSTRUMENT soft key. 3 Select Ports. 4 Press the BLUETOOTH soft key. The Bluetooth Settings menu appears. The BLUETOOTH soft key appears only if a Bluetooth interface is found. HST-3000 Base Unit User’s Guide...

  • Page 59: Specifying Ftp Settings

    This turns the link on (Enabled) or off (Disabled). 6 Select Paired Address and enter the MAC address. The HST-3000 will scan for devices. This may take a minute. If you connect to a system that has a secure connection and requires a password to connect to the HST-3000, use the password “5378”...

  • Page 60: Configuring International Settings

    5 Select a language from the list. The language setting applies to both the wording on the user interface and the voice responses, where applicable. The HST shuts down, and then restarts with the selected language. HST-3000 Base Unit User’s Guide...

  • Page 61: Accessing A Remote Hst-3000

    Bluetooth interface. Remote The optional Remote Operation features allows you to access Operation the HST-3000 user interface from a PC or laptop computer through a virtual network connection (VNC), connecting over an Ethernet interface. NOTE: Remote Operation (VNC) is an optional feature.
  • Page 62 Accessing a remote HST-3000 To use this feature, you must have the VNC viewer provided on the HST-3000 User’s Guide USB; the HST must be connected to the same network as the PC or laptop; and you must know the IP address of the HST-3000.
  • Page 63 The Remote Operation Setting menu appears. 3 Select Remote Operation, and then press 1 to enable remote operation. 4 Insert the HST-3000 user’s guide USB in the PC or laptop, and then launch the VNC viewer, file name vnc_viewer.exe. 5 In the viewer’s server address field, type the HST's IP address, and then select OK.
  • Page 64 VNC availability The VNC program can control the following functions: In Ethernet TE, you can do a ping, trace route and similar data tests, but cannot change any data settings. In DSL, you can perform modem emulate tests with Data mode off. HST-3000 Base Unit User’s Guide...

  • Page 65: Remote Coaching

    Ending a remote Ending a remote operation session involves quitting the operation session session on the PC or laptop and turning the HST-3000 off, and then on again (power cycling). To end a remote operation session 1 On the PC or laptop running the VNC viewer, end the VNC session.
  • Page 66 To launch the remote operation software 1 If you haven’t previously done so, install the software. a Insert the HST-3000 user’s guide USB in the PC or laptop. b Launch the remote operation installation file: remoteop-x.x.x.msi (where x.x.x is the software version).
  • Page 67 1 Press the System soft key and then check the Instru- ment>Ports menu. If the Bluetooth soft key does not appear, you need an external Bluetooth dongle. Connect it to the USB connector on the top of the HST-3000. HST-3000 Base Unit User’s Guide...
  • Page 68 HST and click View Unit. 3 When asked whether you wish to pair with the unit, click Yes. 4 On the HST, from the Bluetooth Settings screen, select Listen For Pair (do not select Pair New Device). HST-3000 Base Unit User’s Guide...
  • Page 69 Troubleshooting This section describes common issues and solutions related to the Remote Operation feature. Please read this section before contacting technical assistance. Issue Where do I find the version information for the Remote Oper- ation software? HST-3000 Base Unit User’s Guide...
  • Page 70 Remote Operation Application. In addition, you can view the Bluetooth configuration informa- tion on the Help>System Information menu. There may be an occasion, such as when contacting Viavi technical support, where you need to access detailed information about the PC's Bluetooth configuration.
  • Page 71 Issue The pairing code window disappears quickly. Resolution The HST was not in “Listen for Pairing” mode. Repeat the pairing process. You selected an HST other than the HST you expected to pair with. Issue HST-3000 Base Unit User’s Guide...
  • Page 72 Resolution You will have to manually pair the HST. Contact your IT department. Issue The viewing window disappears suddenly. Resolution The HST has moved out of range. Move the HST back in range and reconnect. HST-3000 Base Unit User’s Guide...

  • Page 73: Installing X.509 Certificates

    You can then use that file to load identical settings on another unit by loading it from USB or transferring it over an Ethernet connection. To clone a device 1 Press the System navigation key. HST-3000 Base Unit User’s Guide...
  • Page 74 Select Transmit Clone. b Choose where to send the clone: to USB, or transmit over ethernet. IMPORTANT: Choosing Send via Ethernet will close all applications. It is recommended that you transmit clone files before running tests. HST-3000 Base Unit User’s Guide...

  • Page 75: Setting User Preferences

    Adjusting the sound The first selection on the User Preferences menu is Sounds. Using the Sound Settings menu, you can adjust the volume level of the internal speaker. The following procedures describe how to adjust the volume. HST-3000 Base Unit User’s Guide...

  • Page 76: Changing Screen Settings

    To adjust the contrast 1 Access the User Preferences menu (see page 55). 2 Select Screen. The Screen Settings menu appears. 3 Select Contrast. 4 Change the contrast level using the left or right arrow key. HST-3000 Base Unit User’s Guide...

  • Page 77: Adjusting The Backlight Brightness

    Setting the The following procedure describes how to set the backlight backlight activation. activation NOTE: The backlight activation can only be changed for black and white displays. For color displays, the backlight is always on. HST-3000 Base Unit User’s Guide...

  • Page 78: Setting The Backlight Duration

    55). 2 Select Screen. The Screen Settings menu appears. 3 Select Backlight Dur. 4 Enter the desired backlight duration, in seconds, using the keypad. You can set the duration for up to 65 seconds. HST-3000 Base Unit User’s Guide...

  • Page 79: Changing Keypad Settings

    5 Press the OK key. The repeat delay is set. Setting the The following procedure describes how to set the repeat rate. repeat rate This setting defines how many times the character will be repeated per second. HST-3000 Base Unit User’s Guide...

  • Page 80: Setting Auto Power Down Parameters

    The following procedure describes how to control auto power down. NOTE: The HST-3000 will not automatically power down when connected to a charger. To set auto power down parameters 1 Access the User Preferences menu (see page 55).

  • Page 81: Specifying User Information

    NOTE: A valid account ID must be entered in order to synchronize with the StrataSync server. Restoring factory defaults The following procedure describes how to reset the HST-3000 to factory default settings. NOTE: Restoring factory defaults resets test application settings and system settings (such as brightness, contrast, and vol- ume), and powers down the unit.
  • Page 82 Chapter 4 Instrument Settings and User Preferences Restoring factory defaults HST-3000 Base Unit User’s Guide...

  • Page 83: Using The Hst-3000 With A Mobile Device

    This chapter provides task-based instructions for using the optional app that is available for mobile devices. T opics discussed in this chapter include the following: – “Connecting the HST-3000 to a mobile device” on page 64 – “Controlling the device interface” on page 66...

  • Page 84: Connecting The Hst-3000 To A Mobile Device

    Connecting the HST-3000 to a mobile device Using an app on the mobile device (such as an iPad), you can connect to a HST-3000 and control the user interface. Your HST must be equipped with the MOBILEAPP1 option to connect to a mobile device.
  • Page 85 Chapter 5 Using the HST-3000 with a mobile device Connecting the HST-3000 to a mobile device 4 On the mobile device, launch the HST-3000 app. The Controller page appears. 5 T ouch the “Select Device” button in the upper left.

  • Page 86: Controlling The Device Interface

    – Videos–view instructional videos – Accessories– view the guide for the accessories If you are controlling the HST-3000 using an iPhone instead of an iPad, the screen will appear slightly different: Job Manager is not an icon at the bottom.
  • Page 87 Chapter 5 Using the HST-3000 with a mobile device Controlling the device interface T o return to the main Controller page, select the Controller button in the upper left. Table 9 shows the constraints for using the remote access feature.
  • Page 88 Chapter 5 Using the HST-3000 with a mobile device Controlling the device interface HST-3000 Base Unit User’s Guide...

  • Page 89: Hst-3000 Base Unit User's Guide

    Managing Files Chapter 6 This chapter describes how to save test results and manage the files stored on the HST-3000. Topics discussed in this chapter include the following: – “Saving test results” on page 72 – “Using the File Manager” on page 74 –...

  • Page 90: Managing Test Configurations

    The configurations are stored on power down. To store a test configuration 1 Set up the HST-3000 for the test you are performing. 2 Press the Configure navigation key. 3 Press the Storage soft key. 4 Press the 2 key.

  • Page 91: Loading A Configuration

    To overwrite a configuration 1 Press the Configure navigation key. 2 Press the Storage soft key. Press the 3 key. 4 Select the file name to overwrite. 5 Press the OK key. The test configuration is overwritten. HST-3000 Base Unit User’s Guide...

  • Page 92: Deleting A Configuration

    After running a test, you can save the results for future use, such as viewing, printing, or importing into Excel for analysis. The HST-3000 family of products offers several ways to save data: – Save (generic save to text file) –...

  • Page 93: Saving Results To A Text File

    Save locations In addition, the HST-3000 allows you to save the results in either the internal File Manager or to an external USB drive. NOTE: The USB drive must support USB 2.0 and provide access via a standard USB female connector.

  • Page 94: Using The File Manager

    The screen that appears depends on whether you have a USB drive inserted. – If you do NOT have a USB drive inserted, a list of directories appears. – If you have a USB drive inserted, the following screen appears. HST-3000 Base Unit User’s Guide...

  • Page 95: Deleting Files

    A window appears to verify that you want to delete the file. If you don’t want to delete the file, press Cancel. 5 Press the Ok key to delete the selected file. The file is deleted. HST-3000 Base Unit User’s Guide...

  • Page 96: Renaming Files

    To view saved files 1 Access the File Management menu (see page 74). 2 Use the arrow keys to highlight a directory, and then press the OK key. HST-3000 Base Unit User’s Guide...

  • Page 97: Printing Files

    To print files, you will need a battery-to-DB-9 female cable (part number 1217-50-0295) and a printer. NOTE: Viavi recommends using the JDSU PR-40B printer (part number CPR-40B). To do this you will need a null modem adapter (part number 15-018427).

  • Page 98: Sorting Files

    Chapter 6 Managing Files Sorting files To print saved files 1 Connect a printer to the HST-3000: a Using the battery-to-DB-9 female cable (part number 1217-50-0295), connect one end of the cable to the HST’s RS-232 connector. The RS-232 connector is located on the bottom panel of the base unit (see “Using the bottom panel”...

  • Page 99: Transferring Files

    2 Use the arrow keys to find what you wish to copy. You can copy the entire drive, a specific directory, or a single file. 3 Press the Actions soft key, and then select the appro- priate copy action. HST-3000 Base Unit User’s Guide...

  • Page 100: Transferring Files Over Bluetooth

    “USB or HST memory”) which clears when the HST is shut down. Any files in this folder should be trans- ferred to internal HST memory or USB flash to avoid loss of data. HST-3000 Base Unit User’s Guide...

  • Page 101: Transferring Files Using Ftp

    Connect one end of the cable to the HST’s Ethernet port located on the top panel of the unit. See Figure 4 on page b Connect the other end to the network. 2 Access the FTP Settings menu: a Press the System navigation key. HST-3000 Base Unit User’s Guide...
  • Page 102 13 Press the Actions soft key, and then select FTP Send. A confirmation message appears. 14 Press OK. The HST transfers the file to the location specified in step You have finished transferring the file. HST-3000 Base Unit User’s Guide...

  • Page 103: Using A Pc Or Laptop To Transfer Files

    2 Access the Instrument Setup menu: a Press the System navigation key. b Press the INSTRUMENT soft key. The Instrument Setup menu appears. 3 Press the 2 key. 4 Press the ETHERNET soft key. The Ethernet Settings menu appears. HST-3000 Base Unit User’s Guide...
  • Page 104 HST. For example, type ftp 10.10.123.45 where 10.10.123.45 is the IP address for the HST. A user name prompt appears. 4 In lowercase letters type acterna, and then press Enter. A password prompt appears. HST-3000 Base Unit User’s Guide...

  • Page 105: Using A Pc Or Laptop And The File Transfer Utility

    To transfer files using the transfer utility utility 1 Connect the HST to your PC's serial port using the tester to serial (DB9) cable. 2 Run the HST-3000 File Transfer Utility on your PC. HST-3000 Base Unit User’s Guide...
  • Page 106 4 Navigate to the folder on your PC where you want to save the file. To do this... Click... select a drive go “up” a directory open a folder or double click on its name 5 Find the file you would like to transfer on the HST. HST-3000 Base Unit User’s Guide...
  • Page 107 The program verifies that the transfer was a success. 7 To delete files from the HST or the PC, highlight the file then click the “X” icon. This cannot be undone. You have completed the file transfer. HST-3000 Base Unit User’s Guide...
  • Page 108 Chapter 6 Managing Files Transferring files HST-3000 Base Unit User’s Guide...

  • Page 109: Ethernet Te Testing

    “Releasing IP addresses” on page 107 – “Throughput testing” on page 108 – “VLAN scan testing” on page 109 – “Measuring throughput using JDSU QoS” on page 109 – “Interpreting test results” on page 113 HST-3000 Base Unit User’s Guide...

  • Page 110: About Ethernet Te Mode

    Chapter 7 Ethernet TE testing About Ethernet TE mode About Ethernet TE mode In Ethernet TE mode, you can use the HST-3000 to emulate Ethernet terminal equipment by connecting to an Ethernet LAN or to the Ethernet port on the customer's modem. After connecting to the circuit, you can then use trace route, FTP, the web browser, or IP Ping to test for connectivity.

  • Page 111: Specifying Test Settings

    Specifying test settings Specifying test settings Before you begin testing, make sure the test settings on the HST-3000 match the settings of the line that you are testing. Specifying data The following procedure describes how to specify the data settings settings.
  • Page 112 9 If you are testing in Multi-VLAN data mode, select Inter- face x Purpose, and then specify the purpose for that sub-interface (Internet, Video, or Voice). 10 Repeat steps for any remaining interfaces. The data settings are specified. HST-3000 Base Unit User’s Guide...

  • Page 113: Specifying 802.1X Security Settings

    “STUN Enabled” is set to “Yes” on the Data Settings menu. STUN (Simple Transversal of UDP [User Datagram Protocol] Through NATs [Network Address Translators]) allows VoIP calls across a NAT router. These settings should only be changed if necessary. HST-3000 Base Unit User’s Guide...
  • Page 114 The STUN settings are specified. NOTE: If STUN is enabled, the data layer will not come up until the STUN client on the HST has determined the type of NAT used between the HST and the STUN server. HST-3000 Base Unit User’s Guide...

  • Page 115: Specifying Ppp Settings

    Server. Client is normally used. Use Server only when you have a VTU-C. This feature allows a remote VTU-R to establish a PPP session with the HST-3000. NOTE: If you selected “Server” as the PPP mode, connect only to other devices with the same service name.

  • Page 116: Specifying Ping Settings

    The parameter soft keys appear. 2 Press the PING soft key. The Ping Settings menu appears. 3 Press the 1 key, and then set the address type to either IP address or DNS Name (domain name server name). HST-3000 Base Unit User’s Guide...

  • Page 117: Specifying Trace Route Settings

    IP address uses the numeric address. DNS name uses the domain name, such as www.viavisolutions.com. Viavi recommends using the IP address or DNS name of the ISP gateway of the customer's service provider. 4 Select one of the following options: –...
  • Page 118 5 Press the 4 key, and then set the packet type to one of the following: – ICMP (Internet Control Message Protocol) – UDP (User Datagram Packet) 6 Press the 5 key, and then indicate whether you want to lookup names for hops. The trace route settings are specified. HST-3000 Base Unit User’s Guide...

  • Page 119: Specifying Lan Settings

    Select IP Address, then enter the IP address. b Select Net Mask, then enter the net mask address. c Select Gateway, then enter the gateway address. d Select DNS, then enter the address of the DNS server. e Go to step HST-3000 Base Unit User’s Guide...
  • Page 120 – Stateless. Select Stateless if you know that routers on the network allow stateless configuration. When you use Stateless configuration, the instrument generates a tentative link-local address, and then performs Dupli- cate Address Detection (DAD) to verify that the HST-3000 Base Unit User’s Guide...
  • Page 121 DNS Mode, then specify whether the DNS is DHCPv6- Stateless or Static. If DNS Mode is DNS, enter the address of the DNS server. 5 Select Which MAC, then specify either User Defined or Factory Default. HST-3000 Base Unit User’s Guide...

  • Page 122: Specifying Ftp/Http Settings

    4 Press the 3 key, and then indicate whether you want to download or upload. 5 Press the 4 key, and then indicate the upload file size. 6 Press the 5 key, and then specify the upload content, either Pseudo-random or Fixed Pattern - AA55. HST-3000 Base Unit User’s Guide...

  • Page 123: Specifying General Settings

    1 Connect one end of an Ethernet cable to the Ethernet jack on the top of the unit. 2 Connect the other end of the cable to an Ethernet jack. If connecting to a PC, use a cross-over cable. HST-3000 Base Unit User’s Guide...

  • Page 124: Ethernet Te Testing

    5 Press the Start soft key. The HST downloads a certificate (using FTP). 6 Press the Configure navigation key, and then press the DATA soft key. 7 Verify that you are using IPoE Data Mode, and then enable 802.1x Security. HST-3000 Base Unit User’s Guide...

  • Page 125: Testing The Line Quality

    (indicated by a secured/closed lock) or unau- thenticated (an open lock). Testing the line After connected to the line, the HST-3000 gathers statistics for quality the line. These statistics are used to determine the line quality. To test line quality 1 Connect to the line.

  • Page 126: Ping Testing

    Results are updated on the screen. 5 Press the Results soft key to clear or save the results. “Interpreting test results” on page 113 to learn what your results mean. The ping test is complete. HST-3000 Base Unit User’s Guide...

  • Page 127: Tracing The Packet Route

    The following procedure describes how to release an IP address. To release an IP address 1 Press the Home navigation key. 2 Connect the HST to the line. See “Connecting to the line” on page 103. 3 Press the Display soft key. HST-3000 Base Unit User’s Guide...

  • Page 128: Throughput Testing

    (ftp: or http: or, if applicable, https:) and the filename. For example, ftp://10.0.0.1/name 6 Press OK to begin the file transfer. The throughput results appear on the screen. “FTP/HTTP results” on page 120 for information on inter- preting the results. HST-3000 Base Unit User’s Guide...

  • Page 129: Vlan Scan Testing

    PPPoA, PPPoE or IPoE connection, using the Ethernet TE, ADSL, or VDSL link. JDSU QoS is an optional feature. The setup and test items described below will appear only if your unit is equipped with the option. HST-3000 Base Unit User’s Guide...

  • Page 130: Step 1: Specifying Test Settings

    (size of the payload). Download Pkt Size If the Protocol is set to TCP and the Test Type is Download (or Download/Upload), this specifies the size of the packet that is received. HST-3000 Base Unit User’s Guide...
  • Page 131 Upload Jitter Specify the threshold for the jitter for a UDP upload test to the server. Download Rate Specify the threshold for the download rate from the server when running a TCP download test. HST-3000 Base Unit User’s Guide...

  • Page 132: Step 2: Measuring Throughput

    JDSU QoS results to measure throughput. throughput To measure throughput 1 If you haven’t already done so, connect the HST-3000 to the circuit under test. 2 Press the Display soft key and then select JDSU QoS Results. The JDSU QoS result screen appears.

  • Page 133: Interpreting Test Results

    DISPLAY soft key and then selecting the desired results. Ethernet This category provides statistics on Ethernet frames when the Summary HST-3000's 10/100BT Ethernet interface is used in TE mode. Table 10 describes the Ethernet Summary results. results Table 10...

  • Page 134: Ping Results

    (target) automatically responds. Ping tells you if the destination is alive and awake, how fast the ping went to the destination and back to the HST-3000, and if ping packets were dropped and lost along the way. Table 12 describes the ping results.
  • Page 135 Ping results (Continued) Result Definition Echoes returned The number of echo reply messages returned to the HST-3000 from the des- tination. Lost/Lost% The number of pings that did not return to the HST-3000. This could be caused by an unresponsive target (destination) or by heavy congestion on the network;...

  • Page 136: Vlan Scan Results

    Table 14 IP results Result Definition WAN IP The HST-3000's IP address to the access Address or provider network. NOTE: If using Multi VLAN data mode, this result will be the address for the specific VLAN (for example, WAN2 IP Address).
  • Page 137 DNS server to translate an inter- net address into an IP address; then the HST-3000 can correctly route IP pings or other data. The DNS address must be that of a real DNS server, preferably in the pro- vider network.

  • Page 138: Ethernet Results

    The status of each VLAN. Only appears when using IPv4 and Multi VLAN data mode. Ethernet results The Ethernet category provides statistics on Ethernet frames when the HST-3000's 10/100BT Ethernet interface is used in TE or ADSL through-modes. Table 15 describes the Ethernet results.
  • Page 139 Message Status message. JDSU QoS Table 17 describes the JDSU QoS results. results Table 17 JDSU QoS results Result Description Test Type Describes the type of test, for example, UDP Download Only, or TCP Upload/Download. HST-3000 Base Unit User’s Guide...

  • Page 140: Ftp/Http Results

    (upload). Packets Lost The number of packets lost. Loss Ratio Ratio of the number of lost packets to the total number of packets, if running a UDP test. For a TCP test, displays dashes. HST-3000 Base Unit User’s Guide...
  • Page 141 JDSU QoS results (Continued) Result Description Loss QoS Reports Pass/Fail for the Loss test. Jitter (ms) Reports the jitter if running a UDP test. For a TCP test, displays dashes. Jitter QoS Reports the jitter QoS. HST-3000 Base Unit User’s Guide...
  • Page 142 Chapter 7 Ethernet TE testing Interpreting test results HST-3000 Base Unit User’s Guide...

  • Page 143: 802.11 Wireless Testing

    Chapter 8 This chapter provides task-based instructions for using the optional 802.11 wireless testing features. Topics discussed in this chapter include the following: – “About 802.11 testing” on page 124 – “Wireless testing” on page 125 HST-3000 Base Unit User’s Guide...

  • Page 144: About 802.11 Testing

    About 802.11 testing About 802.11 testing In 802.11 mode, you can use the HST-3000 to emulate a wire- less PC or laptop and connect to a wireless network. After connecting to the network, you can then use the data tests as well as the VoIP and Video features.

  • Page 145: Wireless Testing

    – Joining a network – Performing tests – Viewing results To run a wireless test 1 To specify test settings, do the following: a From the 802.11 Station Summary menu, press the Configure navigation key. HST-3000 Base Unit User’s Guide...
  • Page 146 3 Press the Home navigation key to return to the 802.11 Summary screen. The HST-3000 will scan for the SSID that you specified, and attempt to connect to it. 4 To view another result category, do one of the following: a Press the right or left arrow to cycle through the menus.

  • Page 147: Interpreting Test Results

    Chapter 7 “Ethernet TE testing”. To use the Browser, see “Web browser” on page 151. For VoIP tests, see the HST-3000 VoIP Testing User Guide. For IPVideo tests, see the HST-3000 VoIP Testing User Guide. Interpreting test results The following result categories are available in the 802.11 application: –...

  • Page 148: Station Summary Results

    The 802.11b/g channel the particular BSS is operating in. Rx Frames Total frames received. Tx Frames Total frames transmitted. Last Rx Rate The data rate most recently achieved. Last Tx Rate The data rate most recently achieved. HST-3000 Base Unit User’s Guide...

  • Page 149: Bss Details

    Power Save Delivery. APSD is a method to allow 802.11 devices to consume very little power. Protection Whether the BSS requires CTS protection when transmitting. CTS-to-self is a mech- anism used to protect 802.11b devices operating on 802.11g networks. HST-3000 Base Unit User’s Guide...

  • Page 150: Encryption

    Chapter 8 802.11 Wireless Testing Interpreting test results Table 19 BSS Properties results (Continued) Result Definition The association identifier of the HST-3000 in this BSS. Encryption This screen reports encryption statistics. Table 20 describes the Encryption results. Table 20 Encryption results...

  • Page 151: Errors

    Count of bits that transmitted successfully with multiple TX retries. Tx Failed Count of bits that were attempted to be transmitted but failed. This doesn’t always mean the frame was lost, but the HST-3000 did not receive an acknowl- edgement. HST-3000 Base Unit User’s Guide...

  • Page 152: 802.11 Frames

    SSID, BSSID, signal strength, channel number and Range frequency, and the encryption in use are listed. The list can be sorted by SSID or signal strength. Event log This category provides a running log of significant wireless events and errors. HST-3000 Base Unit User’s Guide...

  • Page 153: Stratasync

    StrataSync Chapter 9 This chapter provides task-based instructions for synchro- nizing the HST-3000 with a StrataSync server. Topics discussed in this chapter include the following: – “About StrataSync” on page 134 – “Synchronizing to the StrataSync server” on page 135...

  • Page 154: About Stratasync

    About StrataSync ® StrataSync is a hosted, cloud-based software application that provides Viavi instrument asset, configuration, and test- date management. StrataSync manages inventory, test results, and performance data anywhere with browser-based ease and improves technician and instrument efficiency. Features include the following: –...

  • Page 155: Synchronizing To The Stratasync Server

    To obtain the latest configuration settings, software options and updates, and ownership registration information, the HST-3000 can synchronize with a Viavi server via the internet. The synchronization also stores any user files saved on the unit to the StrataSync server. This procedure should be under-...
  • Page 156 - Press the Home key and then launch the Data appli- cation (highlight XDSL and then press OK). 4 On the StrataSync screen, press the Start Sync soft key. As the process runs, the sync state is displayed in the lower left. HST-3000 Base Unit User’s Guide...
  • Page 157 10 When synchronization is complete, the Status will indicate “Sync Complete”. The unit may be disconnected from the server. The unit has been synchronized to the StrataSync Server. HST-3000 Base Unit User’s Guide...
  • Page 158 Chapter 9 StrataSync Synchronizing to the StrataSync server HST-3000 Base Unit User’s Guide...

  • Page 159: Chapter 10 Optical Tools

    Optical Tools Chapter 10 This chapter provides task-based instructions for using the optional USB accessories. Topics discussed in this chapter include the following: – “Inspecting fiber” on page 140 – “Measuring optical power” on page 144 HST-3000 Base Unit User’s Guide...

  • Page 160: Optical Tools

    Inspecting fiber The Viavi fiber microscope accessory is used to view a live video of a simplex fiber to determine if the fiber is clean. It can also capture a snapshot and provide pass/fail analysis.
  • Page 161 NOTE: Although some microscopes can inspect multi-fiber or rib- bon fiber (depending on the microscope and the tip used) the HST-3000’s microscope application supports simplex fiber only. 3 Press the SCOPE soft key. You may have to scroll right or left to find the soft key. In order for the SCOPE soft key to appear, a Fiber Micro- scope must be plugged into the USB connector.
  • Page 162 PDF report. 8 To view details about the microscope, such as the firm- ware version and serial number, press the ABOUT soft key. 9 Press the Home navigation key. The video of the fiber appears. HST-3000 Base Unit User’s Guide...
  • Page 163 Fiber microscope setup page. If you have a custom profile, you can use it on the HST-3000 by putting the file into the configs/ Microscope folder. For more information on copying or transferring files using the file manager, refer to the HST Base Unit User’s Guide.

  • Page 164: Measuring Optical Power

    PWR METER soft key to appear, an Optical Power Meter must be plugged into the USB connector. The Power Meter Measurements screen appears. 4 Select Optical Power Meter. The Optical Power Meter Summary screen appears. HST-3000 Base Unit User’s Guide...
  • Page 165 To measure a specific wavelength, choose the wavelength. Auto Detect Use Auto-Detect to automatically detect the wavelength. NOTE: Auto-Detect requires a Viavi optical source. LED Threshold Specify the LED threshold (in dBm). This specifies the thresh- old for the power LED on the Optical Power Meter. Solid indi- cates the power is below the threshold (low power), flashing indicates the power is above the threshold.
  • Page 166 (add a text string up to 100 characters to the result file). 10 To view the dB result as a graph, press the Display soft key and then select Graph. NOTE: The graph shows the dB result only (not available for dBm or mW). HST-3000 Base Unit User’s Guide...

  • Page 167: Automated Testing

    Automated Testing Chapter 11 This chapter contains information about the HST-3000 auto- mated testing feature. Topics discussed in this chapter include the following: – “Standard test scripts” on page 148 – “Custom test scripts” on page 148 – “Running a test script” on page 149...

  • Page 168: Standard Test Scripts

    – POTS Close Out Test – Good Pair Check – Wideband Auto Test If you use the HST-3000 with a T1 SIM, you get a standard T1 BERT script. For more information about standard scripts, see the HST- 3000 T1 Testing User’s Guide and the HST-3000 Copper Testing User’s Guide.

  • Page 169: Running A Test Script

    When a menu appears, you can begin using the unit. 3 Press the AutoTest navigation key. The available test scripts appear. The scripts available on your unit will vary depending on the application(s) you purchased, and whether you purchased any custom scripts from Viavi. HST-3000 Base Unit User’s Guide...
  • Page 170 HST-3000c with a Copper SIM attached. – T1 — Shows the available T1 test scripts. This option is only available if you are using an HST-3000 or HST-3000c with a T1 SIM attached. A list of available test scripts appears.

  • Page 171: Web Browser

    Web browser Chapter 12 This chapter describes the HST-3000’s optional web browser. Topics discussed in this chapter include the following: – “About the web browser” on page 152 – “Accessing the web browser” on page 153 – “Navigating the browser” on page 154 –...

  • Page 172: About The Web Browser

    Java. Sites optimized for quick downloads, such as DSLReports.com, are not supported because they are based on Java. The following sections in this chapter describe how to access and use the web browser. HST-3000 Base Unit User’s Guide...

  • Page 173: Accessing The Web Browser

    1 Make sure that you have a network connection, such as PPP over Ethernet. 2 Press the System navigation key. 3 Press the TOOLS soft key. The System Tools menu appears. 4 Select Web Browser. The browser display appears. HST-3000 Base Unit User’s Guide...

  • Page 174: Navigating The Browser

    Navigating the browser You can connect a USB mouse or a USB keyboard/mouse combination to the HST-3000 to navigate the web browser as you would with a desktop computer. If you don’t use a mouse, you can use the HST keypad. The following sections describe how to use keypad to navigate the web browser.

  • Page 175: Selecting Links

    156 for more information. Typing in an The following procedure describes how to type in an address. address To type in an address 1 Press the GO soft key. 2 Select Enter Address. HST-3000 Base Unit User’s Guide...

  • Page 176: Selecting A Previous Address

    The following procedure describes how to add and delete bookmarks. To add or delete bookmarks 1 When on a web page, press the GO soft key. 2 Select Bookmarks. HST-3000 Base Unit User’s Guide...

  • Page 177: Exiting The Browser

    When you are finished demonstrating internet access to the user, you should exit the browser. To exit the browser 1 Press the GO soft key. 2 Select Exit Browser. The browser closes then the last viewed results screen. HST-3000 Base Unit User’s Guide...
  • Page 178 Chapter 12 Web browser Exiting the browser HST-3000 Base Unit User’s Guide...

  • Page 179: Vt100 Terminal Emulation

    VT100 Terminal Emulation Chapter 13 This chapter contains information about using the HST-3000 to emulate a VT100 terminal. Topics discussed in this chapter include the following: – “About VT100” on page 160 – “VT100 cabling” on page 160 – “Emulating a VT100 terminal” on page 165...

  • Page 180: About Vt100

    Chapter 13 VT100 Terminal Emulation About VT100 About VT100 The optional VT100 feature lets you use the HST-3000 to emulate a VT100 terminal, allowing local access to network elements. During a VT100 session, you can retrieve circuit and service performance information, such as loss, margin,...

  • Page 181: Standard Cables

    Chapter 13 VT100 Terminal Emulation VT100 cabling Standard This option allows you to attach the HST-3000 to a network cables element. The standard cable option includes the following: – Viavi custom serial cable – If you have the EZ battery, this will be a custom 6-pin DIN serial-to-DB-9 cable.
  • Page 182 If you have a 14pin battery, you cannot use the AC adapter or cigarette lighter adapter while the standard cables are connected. To use the adapter, you must have the power cabling option (see “Power cables” on page 163). HST-3000 Base Unit User’s Guide...

  • Page 183: Power Cables

    Chapter 13 VT100 Terminal Emulation VT100 cabling Power cables This option allows you to connect the HST-3000 to a network element and use an AC power adapter (or cigarette lighter adapter) simultaneously. If you have an EZ battery, there are no custom cables. Simply attach a power cable: either the standard AC adapter or the optional cigarette lighter adapter.
  • Page 184 “Emulating a VT100 terminal” on page 165. DB-9 female DB-9 male Null modem serial Y-cable DB-9 male HST custom brick Cigarette lighter adapter AC adapter Wall plug Figure 13 VT100 power cabling option with a 14pin battery HST-3000 Base Unit User’s Guide...

  • Page 185: Emulating A Vt100 Terminal

    2 Using either the standard or power cable options, connect the HST-3000 to the network element: Cable Option Connection Standard – Connect one end of the cable (Viavi cable option custom to DB-9 female) to the HST’s RS-232 connector located on the bot- tom panel (see page 17).
  • Page 186 HST’s USB host connector located on the top panel (see page 14). 4 Press the System navigation key. The System Tools menu appears. 5 Press the TOOLS soft key. 6 Select VT100 Emulation. The VT100 Emulation menu appears. HST-3000 Base Unit User’s Guide...
  • Page 187 – NONE (default) Parity Select the parity: – NONE (default) – ODD – EVEN Stop Bits Select a stop bits setting: – 1 (default) – 2 8 Press the File soft key, and then select Connect. HST-3000 Base Unit User’s Guide...
  • Page 188 (while the second function key is still pressed) to page up/down/left/right. The second function key is the blue key (labeled with an arrow) in the lower right corner of the HST keypad. HST-3000 Base Unit User’s Guide...
  • Page 189 12 If you want to transmit a single space, or multiple space characters, press the File soft key and then select the number of spaces. 13 To capture on-screen information to a file: a Press the File soft key. b Select Capture. HST-3000 Base Unit User’s Guide...
  • Page 190 Emulating a VT100 terminal c Enter a file name, and then press OK. The file is saved to the following directory: /results/VT100. 14 To rename, print, or delete a file, see “Managing Files” on page HST-3000 Base Unit User’s Guide...

  • Page 191: Maintenance And Troubleshooting

    Maintenance and Chapter 14 Troubleshooting This chapter describes how to maintain your unit and identify and correct problems related to the HST-3000. Topics discussed in this chapter include the following: – “Maintaining the battery” on page 172 – “Viewing unit options, revisions, and HST ID” on page 182 –...

  • Page 192: Maintaining The Battery

    – Use the AC adapter to power up the HST-3000 the first time you use it or after prolonged storage. – If the battery capacity is depleted or if the battery has been stored for a prolonged period, use the Viavi battery charger to charge the battery.

  • Page 193: Conditioning The Battery

    – There is a thermal fuse on the 6 cell (series / parallel) pack – There is a protection IC on the flex circuit inside the pack that will disconnect the pack for the following conditions: overcharge, overdischarge, or overcurrent. HST-3000 Base Unit User’s Guide...

  • Page 194: Recharging The Battery

    HST-3000. To charge the battery 1 Connect one end of the AC adapter to the connector on the battery. The HST’s battery connector is located on the unit’s bottom panel. Charger connector HST-3000 Base Unit User’s Guide...

  • Page 195: Led Troubleshooting

    Do not use outdoors or in wet locations. Use only the AC Adapter supplied with the test set. 3 Let the HST-3000 charge for up to 7 hours depending on the voltage level. The charging time will be the same whether the power is on or off.
  • Page 196 This would normally indicate an external short of the pack. HST-3000 Base Unit User’s Guide...
  • Page 197 Battery LEDs If you have an EZ battery, there are two LEDs on the battery: OK and CHARGE. Their function is described below. The OK light is lit green when charging is complete. HST-3000 Base Unit User’s Guide...
  • Page 198 0 to 60 C +/- 5C. The minimum or maximum cell voltage is out of range. This would indicate a bad pack. Bad battery pack Off. Charger cannot detect the battery pack. HST-3000 Base Unit User’s Guide...

  • Page 199: Replacing The Battery

    There is danger of extreme heat, fire, or explosion if battery is incorrectly replaced or if it is tampered with. Replace only with an Viavi recommended battery. Follow the battery replacement procedure exactly and do not tamper with the battery case.
  • Page 200 The expected life of the battery pack is 2 to 3 years. The pack should maintain at least 70% of it's original capacity after 300 charge cycles. This is not to say the battery is useless after that but that the capacity will start diminishing over time. HST-3000 Base Unit User’s Guide...

  • Page 201: Resetting The Battery Capacity Indicator

    2 Turn off the HST. 3 Leave the charger connected to the unit. 4 Verify that the HST-3000 is off (powered down). 5 Press and hold the Auto Test navigation button while turning the power on. The Batt LED turns green.

  • Page 202: Viewing Unit Options, Revisions, And Hst Id

    55). 3 Select Power Management. The Power Management Settings menu appears. NOTE: The HST-3000 should have a full battery charge when you perform this operation. 4 Select Reset Batt. Gauge. The battery capacity indicator is reset. Viewing unit options, revisions, and HST ID The following procedure describes how to view unit options and revisions, and the HST ID number.

  • Page 203: Adding Options

    Viewing revisions and options is complete. Adding options The HST-3000 software allows you to add new options to your unit in the field by entering a unique number key that will un- lock the new feature. Contact your sales representative or call Viavi customer service to order your new feature and obtain the unique key for your unit.

  • Page 204: Updating The Software

    To update from a PC or laptop 1 Install the HST Updater program (provided with software updates) on a PC or laptop running one of the following operating systems: Windows 98, Windows 2000, Windows XP, or Windows NT. HST-3000 Base Unit User’s Guide...

  • Page 205: Updating Over An Intranet Or Network

    5 Use a shielded Ethernet crossover cable to connect the HST-3000 to a PC or laptop. NOTE: ELECTROSTATIC DISCHARGE Viavi recommends using a shielded crossover cable to help prevent electrostatic discharge (ESD). 6 To update the software, follow the JDSU updater program instructions on screen.

  • Page 206: Updating Over A Wan

    Chapter 14 Maintenance and Troubleshooting Updating the software 3 Connect the HST-3000 to the AC charger adapter to ensure an uninterrupted supply of power during the update. WARNING: ELECTRICAL SHOCK Electrical shock may result in serious injury or death. Be sure the AC adapter is connected to the correct voltage mains.
  • Page 207 8 Press the Cancel key to return to the Instrument Settings menu. 9 Press the 7 key. The Software Update screen appears. 10 Press the 1 key to select WAN. The SW Update WAN Settings screen appears. HST-3000 Base Unit User’s Guide...

  • Page 208: Updating Using Usb Flash

    The unit powers down when done. Updating using To update over USB USB Flash 1 Connect the HST-3000 to the AC charger adapter to ensure an uninterrupted supply of power during the update. WARNING: ELECTRICAL SHOCK Electrical shock may result in serious injury or death. Be sure the AC adapter is connected to the correct voltage mains.

  • Page 209: Rotating The Lcd

    1 Turn off the unit. 2 Press and hold the System navigation key while powering up the HST-3000. The HST-3000 enters the software update mode. 3 Select item 7 - Rotate LCD. 4 Turn off the HST. When you turn on the HST, he screen is in the correct orien- tation.

  • Page 210: Locating The Serial Number

    HST. Please read this section before contacting technical assistance. Installation and This section addresses questions that may be asked about preparing the HST-3000 for use. setup Issue The unit will not power up. Resolution Check the power source and restart the unit.

  • Page 211: Operation

    Issue When I attempt to charge the battery, I get a flashing red CHARGE LED. Resolution The battery temperature is either too high or too low. Let the battery reach room temperature then try again. HST-3000 Base Unit User’s Guide...
  • Page 212 Issue When I try to change the contrast, nothing happens. Resolution The contrast control, along with the backlight activation and backlight duration, is not applicable to the color display. However, you can control the brightness of the backlight, which may help with the contrast. HST-3000 Base Unit User’s Guide...

  • Page 213: Appendix A Specifications

    Specifications Appendix A This appendix describes the HST-3000 specifications. Topics discussed in this appendix include the following: – “Physical specifications” on page 194 – “Environmental specifications” on page 194 – “Power specifications” on page 195 HST-3000 Base Unit User’s Guide...

  • Page 214: Physical Specifications

    Storage Temperature -40 to 140 F (-40 to 60 C) Operating Humidity 10% to 90% RH non-condensing Storage Humidity 10% to 90% RH non-condensing Vibration 3 axis random vibration Shock 3 foot drop onto concrete HST-3000 Base Unit User’s Guide...

  • Page 215: Power Specifications

    300 charge cycles. Battery recharge time Up to 7 hours Power supply input 100 to 240 VAC, 50/60 Hz, autosens- Power supply input 5 A @ 115 VAC, 3 A @ 230 VAC current HST-3000 Base Unit User’s Guide...
  • Page 216 Appendix A Specifications Power specifications HST-3000 Base Unit User’s Guide...

  • Page 217: Index

    Cabling VT100 options VT100 power option Backlight VT100 standard option activation, setting brightness, adjusting Cancel key duration, setting Clone Base unit Compliance information copper Configurations features cloning options deleting Battery loading checking conditioning HST-3000 Base Unit User’s Guide...
  • Page 218 See also time, date Event log 119, International settings Exiting menus IP results Factory defaults, restoring Keypad 10, Features Keypad settings, changing Files Bluetooth transfer Keys deleting arrow manager cancel printing navigation renaming using Bluetooth power second function HST-3000 Base Unit User’s Guide...
  • Page 219 Optical tools 139–146 disabling fiber microscope enabling optical power meter Ethernet connection Options using a PC keyboard adding Removing the module base unit Renaming files loading software See also SIMs Repeat delay, setting Repeat rate, setting HST-3000 Base Unit User’s Guide...
  • Page 220 Soft keys 10, 11, Time, setting Software loading upgrades and options Top panel Trace route Software options setting parameters 97–98 tracing the packet route Software, updating 184–189 Transferring files Sorting files Bluetooth Sound, adjusting 81–87 HST-3000 Base Unit User’s Guide...
  • Page 221 Updating software 184–189 connector devices, viewing Web browser accessing User interface 18–22 adding/deleting bookmarks User preferences, setting exiting navigating opening a web page option and part number Wireless 802.11 testing 124–132 Viewing files options revisions HST-3000 Base Unit User’s Guide...
  • Page 222 Index HST-3000 Base Unit User’s Guide...
  • Page 224 21109336-013 Revision 001, 02/2016 English Viavi Solutions North America: 1.844.GO VIAVI / 1.844.468.4284 Latin America +52 55 5543 6644 EMEA +49 7121 862273 APAC +1 512 201 6534 All Other Regions: viavisolutions.com/contacts email TAC@viavisolutions.com...

Table of Contents

Save PDF