Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Electrolux EYL85016WM
Summary of Contents for Electrolux EYL85016WM
- Page 1 EYL85016WM WATER HEATER USER MANUAL EYL95016WM EYL10516WM...
-
Page 2: Table Of Contents
9. TROUBLESHOOTING..................23 WE’RE THINKING OF YOU Thank you for purchasing an Electrolux appliance. You’ve chosen a product that brings with it decades of professional experience and innovation. Ingenious and stylish, it has been designed with you in mind. So whenever you use it, you can be safe in the knowledge that you’ll get great results every time. - Page 3 In the user manual and on our web site, www.electrolux.co.uk you will find some useful information on how to deal with minor faults and how to take care of your product. When contacting us for...
-
Page 4: Safety Information
1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. - Page 5 ENGLISH The pressure relief device must be fitted during installation, unless it is incorporated in the appliance. The appliance must be permanently connected to fixed wiring. The appliance must be earthed. Do not install the appliance in locations where freezing can occur.
-
Page 6: Safety Instructions
Do not let the electricity mains cable tangle. All products manufactured and supplied by Electrolux are safe provided they are Make sure the appliance is installed installed, used correctly and receive regular correctly. Loose and incorrect electricity... - Page 7 Turn off at the mains electrical supply and refer to the Troubleshooting section (see page 23) or contact Electrolux Customer Services (see page 3). Do not crush or kink the shower hose, this could damage the hose, cause leaks and activate the pressure relief device.
-
Page 8: Electrical Requirements
3. Electrical Requirements Double pole switch Shower unit For cable capacity see cable current carrying capacity table on page 5 Consumer unit Mains electrical supply supply company. WARNING! This appliance MUST be earthed! The shower must be connected to its own independent electrical supply. - Page 9 ENGLISH 3. Electrical Requirements Where shower cubicles are located in any For close circuit protection DO NOT use a rooms other than bathrooms, all socket rewireable fuse. Instead use a suitably rated Miniature Circuit Breaker (MCB) or cartridge outlets in those rooms must be protected by fuse (see Circuit protection table).
-
Page 10: Water Requirements
4. Water Requirements Isolating stop valve Mains water Shower unit supply Hose retainer 1m minimum height from shower unit to floor Minimum 25mm between showerhead Bath spillover and spillover level This shower needs to be installed in If the shower is to be installed in a hard water... -
Page 11: Installation
ENGLISH 5. INSTALLATION WARNING! Water entry position: Before installation, make sure Bottom right inlet entry you read through the electrical requirements and water requirements section. Select the location and hang up the shower While planning your shower installation, make sure you allow sufficient clearance between the ceiling and walls to allow any future maintenance (cleaning the filter etc.) to be performed. - Page 12 5. INSTALLATION Top right inlet entry Left inlet entry Top left inlet entry Bottom left inlet entry To mark the drilling position Rear left inlet entry Using the installation template supplied, mark the positions of the three fixing holes.
- Page 13 ENGLISH 5. INSTALLATION Fig. 4. To remove the front cover Unscrew the screws that fixing the front cover (Fig. 2), then remove the front cover. NOTE: The knobs and On/off button are fixed on the front cover. Do not try to remove them.
- Page 14 Electrical wiring connection NOTE: To select the wiring terminal position through to remove debris and swarf that This Electrolux shower heater has 2 wiring could otherwise damage the unit. terminals and 2 earthing terminals shown A proper sealant should always be used as Fig.
- Page 15 ENGLISH 5. INSTALLATION 5. While applying slight pressure to the cover, 3. Reassemble the water inlet cover. secure in position with the retaining screws. 4. Check to ensure that the wiring is not 6. Once you place the front cover on the trapped and replace the cover squarely to back cover properly fix the front cover with the backplate and guide into position so that...
- Page 16 5. INSTALLATION 5.5 Install the bracket NOTE: Use the flexible hose to locate the proper position for the bracket if necessary. Bracket parts Put the wall plugs on the holes, then Sliding rail remove the sliding rail holder covers from...
- Page 17 ENGLISH 5. INSTALLATION b. Assemble the soap tray holder from the bottom of the sliding rail as Fig. 12 shown. Fig. 12 Point the open gap upward c. Assemble the soap tay on the soap tray holder. d. Place the sliding rail between the holders and fix the sliding rail by fixing the lower holder as Fig.
-
Page 18: Operation Instruction
6. OPERATION INSTRUCTION Product features The following operation is intended to flush out any remaining debris, and to make sure the heater unit contains water before the heating elements are switched on. 1. Make sure the flexible hose is screwed... - Page 19 ENGLISH 6. OPERATION INSTRUCTION CAUTION! When not using the shower unit, insolate Failure to turn the control to the the unit from main circuit via the double minimum flow position MAY cause pole switch. the PRD(Pressure Relief Device) to WARNING! operate.
- Page 20 6. OPERATION INSTRUCTION To increase the shower temperature Turn the temperature control clockwise - this will decrease the flow of water through the shower and make the water hotter. NOTE: Total rotation distance of the temperature knob is 300°.
-
Page 21: Maintenance
ENGLISH 7. MAINTENANCE WARNING! Inspect the ‘O’ ring for damage when the filter cap is removed. Before maintenance work, you must When cleaning the filter, DO NOT use a switch off the power at the isolating switch. sharp object, as it will cause damage. It is preferable to use an old toothbrush or similar. -
Page 22: Helpful Hints And Tips
8. HELPFUL HINTS AND TIPS Cut off the power while not in use avoid block of internal water pipe and lime scale. In normal use, it is in order to leave the water supply permanently on to the shower unit,... -
Page 23: Troubleshooting
(see rating label). Fit pump to give minimum pressure (see rating label). Electrolux Contact Customer Service for advice. Water too cool or cold. Readjust flow rate to give reduced flow or Reduction in ambient select higher power. - Page 24 9. TROUBLESHOOTING Problem/Symptom Cause Action/Cure Shower varies from Water pressure has Wait until the water pressure resumes to normal temperature dropped below minimum normal. to cold during use. required. Clean or replace blocked sprayplate in Blocked showerhead. showerhead and then fit new PRD.
- Page 25 www.electrolux.com/shop...