Page 1
Instructions 020-2664-00 TLA7012 Portable Logic Analyzer Rackmount Kit 071-1750-00 Warning The servicing instructions are for use by qualified personnel only. To avoid personal injury, do not perform any servicing unless you are qualified to do so. Refer to all safety summaries prior to performing service.
Use Care When Servicing With Power On. Dangerous voltages or currents may exist in this product. Disconnect power and disconnect test leads before removing protective panels, soldering, or replacing components. To avoid electric shock, do not touch exposed connections. TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
The rackmount kit is a collection of parts that, once installed, configure the instrument for mounting into a standard 19-inch equipment rack. Products TLA7012 All Serial Numbers TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
407-5125-00 BRACKET, RACKMOUNT GUIDE, SET OF 4 W/HARDWARE 1 ea 407-5131-00 BRACKET, PORT RACKMNT ADAPTER (R) 1 ea 407-5124-00 BRACKET, PORT RACKMNT ADAPTER (L) 2 ea 367-0530-00 HANDLE: BOW NS - Not Saleable TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
Cooling air enters from the bottom-front and right sides as shown in Figure 3. You must provide adequate cool air to meet the ambient temperature require- ments listed in Table 1. Hot air out (rear) Measure input air temperature Figure 3: Instrument cooling TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
CAUTION. Adhering to these clearance requirements provides the rack-mounted instrument with sufficient clearance for air circulation and accommodation of the power cord and mounting hardware. Failure to provide these clearances can result in overheating and can cause instrument faults or failure. TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
Page 11
Kit Description 541. mm (21.300 in) 412.02 mm (16.230 in) 480.00 mm (18.897 in) 352.1 mm 352.1 mm (13.862 in) (13.862 in) Figure 4: Instrument with rack adapter installed TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
Installation Instructions This section contains all procedures needed to rackmount the TLA7012 instrument. CAUTION. This kit requires you to remove the right-side panel of the instrument rack you intend to use. You must have access to the right side of your instrument to connect the logic analyzer probes when the instrument is installed in the rack .
Page 14
You must slide the rail within the track assembly to gain access to the mounting screws and holes. See the latch detail in Figure 6 on page 13). Mounting screw Flat head screw Bracket Figure 5: Preparing the track assembly TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
Page 15
Refer to Figure 6 to help you attach the tracks to the shelf. Use this hole for the second screw Push in latch to slide the rail Slide the rail and add the second screw Figure 6: Rackmount shelf preassembly TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
Page 16
See Figure 7. 12.7 mm (0.50 in)(for 355.60 mm correct position of (14.00 in) securing holes) 21.081 mm (.830 in) Figure 7: Vertical clearances for rack installation (left-front rail shown) TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
Page 17
Use two flat-head screws if the cabinet rails have countersunk mounting holes; otherwise use two pan-head screws Mounting Method A Mounting Method B Figure 8: Installation of slide-out track assemblies in rack (top view) TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
Page 18
1. Grab the shelf/track assembly and slide the tracks into the brackets on the rear rails of the instrument rack. 2. Align the front of the shelf to the bottom of the cosmetic trim on the front of the instrument rack. TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
Page 19
5. Tighten all of the screws and check that the shelf slides in and out easily. Loosen and adjust, if necessary. This completes the installation of the shelf/track assembly into the rack. Next, perform the Attach Brackets to the Instrument procedure. TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
Page 20
4. Fold the front feet down flat against the bottom of the instrument. This completes the installation of the rack-adapter hardware to the instrument. Next, do the following procedure: Mount the Instrument to the Shelf. TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
After completing the installation procedure, the installers should verify that the instrument and rack cabinet will not tip forward while the instrument is in the extended position. TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
Page 22
The handle, by first removing the right-side cover (six screws), and then the two handle screws. Replace the cover and mount the handle on the shelf as described in step 8. TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
Page 23
9. If necessary, reattach the power cord to the instrument by turning the mounting post 1/4-turn counter-clockwise. 10. Connect the power cord to the instrument receptacle and the AC source in the instrument rack. TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
Page 24
5. Connect the probe to the module. NOTE. It may be easier to first route all of the probes that you need through the shelf, and then connect them to the modules. TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...
Page 25
Probes out front Figure 14: Routing the probes 6. Repeat steps 2 through 5 for the remaining probes. 7. Connect the probes to your DUT. g End of document g TLA7012 Portable Logic Analyzer Rackmount Kit Instructions...