Download
Share
Print this page
Tinycontrol Lan Controller v3 Manual
  1. Manuals
  2. Brands
  3. Tinycontrol Manuals
  4. Controller
  5. Lan Controller v3
  6. Manual

Tinycontrol Lan Controller v3 Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
LAN Controller V3.0
Manual

Advertisement

loading
Need help?

Need help?

Do you have a question about the Lan Controller v3 and is the answer not in the manual?

Questions and answers

Related Manuals for Tinycontrol Lan Controller v3

Summary of Contents for Tinycontrol Lan Controller v3

  • Page 1 LAN Controller V3.0 Manual...

  • Page 2: Example Of Applications

    LAN Controller V3.0 – LANKON-008 LAN Kontroler Lan Controller v3 is a completely new version of device produced from 2011y. A small board works as a web server which presents the various sensor readings: tem- perature, humidity, voltage, current, events and allows you to remotely control up to 10 outputs.
  • Page 3 LAN Controller V3.0 – LANKON-008 Monitoring, Controlling, Restarting FEATURES: • 4 analog inputs • 2 analog inputs up to 3,3V - for DC voltage, DC current or other physical quantities by voltage output sensors, • digital buses: 1wire - up to 6 DS18B20 temperature sensors, I2C - up to 2 sensors, for example AM2320 humidity sensor, • 4 logical inputs, as state (high, low) sensors (open, close, PIR) and for pulse counters...

  • Page 4: Factory Settings

    LAN Controller V3.0 – LANKON-008 FACTORY SETTINGS • IP address of the module: 192.168.1.100 • administrator: admin password: admin • user: user password: user TECHNICAL SPECIFICATIONS • supply voltage: 8 ÷ 55 V DC • power consumption: 0,5W - without an attached relays • PoE supply: YES, passive (PoE max. <55 V) • Protection from wrong supply polarization: YES...
  • Page 5 LAN Controller V3.0 – LANKON-008 PINS and COMPONENTS DESCRIPTION GND SPI_SDO SPI_SCK SPI_SDI SPI_CS +3,3V IDC10-1 power LED Zasilanie INP1D max 55V INP2D INP3D green LED INP4D Ethernet 100 Mbit. GND* PoE max 55V INPA1 orange LED INPA2 INPA3...

  • Page 6: Reset Button

    LAN Controller V3.0 – LANKON-008 RESET BUTTON Pressing for about 0.5 seconds to change state relays, and hold for longer - up to around five seconds will change all settings (both network and configuration) on the factory re- set. Confirmation of the settings is fast switching on and off the relay (click-click), not to be confused with the change of status and exclusion of the relay after a reboot.
  • Page 7 LAN Controller V3.0 – LANKON-008 IDC10-2 socket: Connection OUT1÷OUT4 OUT1÷OUT4 are open collector, it means that the switching means connecting mass of the system. So, it can be actuated, for example relays, motors of low power (fans), connecting on the one hand to the output OUT "–"...
  • Page 8 LAN Controller V3.0 – LANKON-008 SENSORS CONNECT 1. Measurement of DC voltage at the inputs INPA1÷INPA4 (3÷33V) To enable the measurement to be in the "Input" to choose for INPA1÷INPA4 range Vin = 3.3V or 33V, and possibly small signal strengthening GAIN.
  • Page 9 LAN Controller V3.0 – LANKON-008 2. Measurement of the DC voltage through resistive divider If you need to measure the voltage higher than 33V to INPA1÷INPA4 or 3.3V on INPA5, INPA6 use a resistive divider. U voltage dividers connected to the terminals should be safe, or properly protected against accidental shock hazard.
  • Page 10 LAN Controller V3.0 – LANKON-008 3. Connection the current sensor ACS711ex The sensor can measure DC currents to 15A or 30A (depending on the version of the sensor). It can be connected to all analog inputs: INPA1÷INPA6. Power supply: + 3.3V (pin 3 of the output IDC10-1).
  • Page 11 LAN Controller V3.0 – LANKON-008 5. Connection of the AC sensor SCT 013 030 white INPA1 The sensor can measure AC currents up to 30A with a resolution of about 50mA, but for a power supplies of low PF, measurement inac- curacies can be significant.
  • Page 12 LAN Controller V3.0 – LANKON-008 7. Connection the PT1000 temperature sensor R=3,3kΩ PT1000 INPA1÷INPA4 To enable the measurement to be in the "Input" to choose for INPA1÷INPA4 measurement PT1000. Attention: PT1000 analog sensor require calibration due to cable resistance.
  • Page 13 LAN Controller V3.0 – LANKON-008 9. Connection distance sensor yellow INPA1÷INPA6 black Sharp GP2Y0A02YK0F sensor allows measurements of distances in the range of 20 to 150 cm by using infrared reflection. It can be connected to the inputs INPA1÷INPA6, set to 3.3V.
  • Page 14 LAN Controller V3.0 – LANKON-008 11. Connection of PIR motion/presence sensor The sensor uses a analysis of the infrared radiation. Low state logic output is a state of rest, a state indicating the activity is high. The detector can be adequately linked to + 5V, GND, and one of the digital inputs INP1D÷...
  • Page 15 LAN Controller V3.0 – LANKON-008 NOTES www.tinycontrol.eu...
  • Page 16 LAN Controller V3.0 – LANKON-008 Management by WWW. All functions Lan Controller v3 are available for configuration and viewing via the website. There are two types logon: as an administrator and user. The administrator has access to all settings, the user only to the panel status, which sees only what will make an administrator.
  • Page 17 LAN Controller V3.0 – LANKON-008 - RESET - reset the position of elements - EN - site language 3. ON/OFF Output panel: out0 ÷ out5 - displays the names of outputs and the switching which is also an indicator of the output - ON / OFF 4.
  • Page 18 LAN Controller V3.0 – LANKON-008 3. Control - page is only visible to the administrator. It contains a set of pages to configure the inputs and outputs visible in Status. Control / Out 1. ON/OFF output panel - allows you to select which outputs out0÷out6 may be visible.
  • Page 19 "mode on/off "- check this box causes the PWM output changes in the output of the two state: on / off. NOTE: for the Lan Controller v3 is available a separate system - board - the overlay transi- stor, which allows you to use PWM outputs to control the load of up to 2÷4A (depending on the amount used of outputs) and a voltage input connected to the cap (maximum 28V).

  • Page 20: Control Inputs

    LAN Controller V3.0 – LANKON-008 Control / Inputs 1. Input analog measurement inclusion panel and input name field. ATTENTION: when you save names are allowed ONLY characters: a ÷ z, A ÷ Z, 0 to 9, and "_" (underscore) without nationality characters.

  • Page 21: Control / Events

    LAN Controller V3.0 – LANKON-008 Control / Events Events is a simple mechanism for the creation of Lan Controller machine performing pro- grammed actions in the event of certain conditions, such as switching out1 when the tem- perature exceeds the specified value, sending an e-mail when you change the logic state etc.
  • Page 22 LAN Controller V3.0 – LANKON-008 Control / Watchdog Watchdog is basic tool for local/internet network administrators. By sending an ICMP pac- ket (ping) to configured address it guards if remote machine answers and if necessary, can reset power such as client device. It maybe used in homes, especially to reset the radio equipment or modems operating on long cables, more susceptible for interferences.
  • Page 23 LAN Controller V3.0 – LANKON-008 Control / Scheduler Scheduler is a list of tasks to be performed within a specified time, or periodically at certain days and times. 1. In this field, enter the name of the event. 2. From the selection menu, select the output which is to be action and select the desired logical value "0"...
  • Page 24 LAN Controller V3.0 – LANKON-008 Control / Duraluxe The option of reading the value of electricity production and power network of the inver- ters of Duraluxe. Communication with the inverters takes place via the RS232 interface. Description supplied to these devices.
  • Page 25 LAN Controller V3.0 – LANKON-008 Control / Power/Energy Power/Energy tab is used to set power settings and energy monitored by the energy me- ter with pulse output or measuring current and voltage sensors connected to the analog inputs INPA1 ÷ INPA6.

  • Page 26: Config / Network

    LAN Controller V3.0 – LANKON-008 4. Config / Network Config / Network 1. MAC Adress - field display its value (Each Lan Controller has a unique address, it can be identified in case of connection of several devices). 2. Host Name - a place to put a personalized Lan Controller name.
  • Page 27 LAN Controller V3.0 – LANKON-008 Config / Time 1. NTP / Set manual - selecting the desired option to "manual" input the date and time (Set manual) or a choice of designated NTP server. 2. NTP Servers - field to enter the...
  • Page 28 LAN Controller V3.0 – LANKON-008 Config / HTTP Client: the client sends HTTP requests using the GET to the specified server and port at a specified time. The way the "paste" the sensor looks like this: %xxy - where: % –...
  • Page 29 LAN Controller V3.0 – LANKON-008 MQTT Client MQTT protocol pis designed primarily to exchange data between devices on the Internet of Things and servers and client devices such as smartphones. The main advantage is to keep the connection in both directions, making it possible to control a simple Lan Controller located on the local network with the phone being in the local network operator.
  • Page 30 LAN Controller V3.0 – LANKON-008 Config / Remote control Lan Controller has a functionality to send controlling packets from one to other (by UDP protocol).This way we can switching on/off OUTx outputs of Lan Controller (Server) by the pushing INPDx to GND on other device (Client). Controllers should be connected, nut can be away from each other.Most frequently this feature could be used in local network of one...
  • Page 31 LAN Controller V3.0 – LANKON-008 Assigning an item number for the currently connected sensor DS18B20. Config / Temperature sensor 1. Connect chosen sensor (others should be removed), 2. Refresh the button "Read id", (if it does not appear ID, reset Lan Controller), 3.
  • Page 32 LAN Controller V3.0 – LANKON-008 Config / Access 1. ZChecking the "Auth Enabled" will make the administration of the device address in the browser login window will appear, to prevent access to the XML data without authoriza- tion. While the second login window is set to distinguish the type of access: the admini- strator or the user (admin/admin lub user/user).
  • Page 33 When you press the button, we have 1 min. to upload firmware. 2. WWW Upgrade - Lan Controller v3 is able to modify or even create a new web interface. For this purpose use a www generator. (You can download it from our website).
  • Page 34 LAN Controller V3.0 – LANKON-008 Reading XML data Reading is possible or if the authorization is disabled and we are already logged in. If not, you should specify before your username and password, for example: admin:admin@192.168.1.100/xml/(...) The basic list of positions XML files to read data from: basic sensors: 192.168.1.100/xml/ix.xml...
  • Page 35 LAN Controller V3.0 – LANKON-008 NUMBERS OID for SNMP OUT0÷OUT5 and PWM0÷PWM3 can read and write, the rest is read only. OUT0 iso.3.6.1.4.1.7616.3.1.0.0 = INTEGER: 0 OUT1 iso.3.6.1.4.1.7616.3.1.1.0 = INTEGER: 0 OUT2 iso.3.6.1.4.1.7616.3.1.2.0 = INTEGER: 0 OUT3 iso.3.6.1.4.1.7616.3.1.3.0 = INTEGER: 0 OUT4 iso.3.6.1.4.1.7616.3.1.4.0 = INTEGER: 0...
  • Page 36 © Konsorcjum ATS Sp.J. Copying, duplication, reproduction whole or in part without the consent of the owner is prohibited. Konsorcjum ATS Sp.J. ul. Żeromskiego 75, 26–600 Radom, POLAND tel./fax: +48 48 383 00 30, e-mail: sales@ledats.pl www.tinycontrol.eu, www.ledats.pl, www.wirelesslan.pl, www.ats.pl...

This manual is also suitable for:

Lankon-008