EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 1.5 Pin Definition Pin Number Symbol Type Function Power Supply for Logic This is a voltage supply pin. It must be connected to external source. This is a ground pin. It also acts as a reference for the logic pins, the OEL driving voltages, and the analog circuits.
Page 7
EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 1.5 Pin Definition (Continued) Pin Number Symbol Type Function t erface l Cl k Input The transmission if information in the bus is following a SCLK clock signal.
EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 Parameter Symbol Unit Notes Supply Voltage for Logic -0.3 1, 2 Supply Voltage for Display 1, 2 °C Operating Temperature °C Storage Temperature Note 1: All the above voltages are on the basis of “VSS = 0V”.
EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 3. Opti c s & r ic r is 3.1 Optics Characteristics Characteristics Symbol Conditions Typ Max Unit With Polarizer Brightness cd/m (Note 3) 0.26 0.32 0.34 C.I.E.
EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 3.3 AC Characteristics Symbol Description Unit Clock Cycle Time cycle Address Setup Time Address Hold Time Chip Select Setup Time Chip Select Hold Time Write Data Setup Time...
EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 F un e cif 4.1. Commands Refer to the Technical Manual for the SSD1306 4.2 Power down and Power up Sequence To protect OEL panel and extend the panel life time, the driver IC power up/down routine should include a delay period between high voltage and low voltage power sources during turn on/off.
EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 4.4 Actual Application Example Command usage and explanation of an actual example <Initialization> Set Display Off Set Segment Re-Map Set Entire Display On/Off 0xAE 0xA1 0xA4 Set Display Clock Divide Ratio/Oscillator Frequency...
EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 6.1 Environment Required Customer’s test & measurement are required to be conducted under the following conditions: 23 ± 5°C Temperature: 55 ± 15 %RH Humidity: Fluorescent Lamp: ≥...
Page 17
EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 6.3.1 Cosmetic Check (Display Off) in Non-Active Area (Continued) Check Item Classification Criteria Any crack is not allowable. Panel Crack Minor Cupper Exposed Not Allowable by Naked Eye...
Page 18
EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 6.3.1 Cosmetic Check (Display Off) in Non-Active Area (Continued) Check Item Classification Criteria NG if any bent lead cause lead shorting. Minor Terminal Lead Bent (Not Twist or Broken) NG for horizontally bent lead more than 50% of its width.
EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 6.3.2 Cosmetic Check (Display Off) in Active Area Check Item Classification Criteria Any Dirt & Scratch on Ignore for not Affect the Acceptable Polarizer’s Protective Film Polarizer W ≤...
EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 6.3.3 Pattern Check (Display On) in Active Area Check Item Classification Criteria No Display Major Flicker Major Not Allowable Missing Line Major Pixel Short Major Darker Pixel...
EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 8.1 Handling Precautions Since the display panel is being made of glass, do not apply mechanical impacts such us dropping from a high position. If the display panel is broken by some accident and the internal organic substance leaks out, be careful not to inhale nor lick the organic substance.
EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 11) Protection film is being applied to the surface of the display panel and removes the protection film before assembling it. At this time, if the OEL display...
EASTRISING TECHNOLOGY CO.,LIMITED 旭 日 东 方 科 技 有 限 公 司 8.4 Precautions when disposing of the OEL display modules Request the qualified companies to handle industrial wastes when disposing of the OEL display modules. Or, when burning them, be sure to observe the environmental and hygienic laws and regulations.
Need help?
Do you have a question about the ER-OLED0.91-1 and is the answer not in the manual?
Questions and answers