Metrologic MS7120 Scanner Setup Manual
  1. Manuals
  2. Brands
  3. Metrologic Manuals
  4. Barcode Reader
  5. MS7120 Orbit
  6. Scanner setup manual

Metrologic MS7120 Scanner Setup Manual

Hide thumbs Also See for MS7120:

Advertisement

Table of Contents

See also: Installer and User Manual
Introduction
Purpose
This document contains a verification sequence that allows you to determine whether your
scanner is configured correctly, and a programming sequence to follow if it is not configured
correctly.
Be aware of the following:
• Refer to MDE-4389 Setting Up Datalogic™ DLL2020 Bar Code Scanner Used on
• Refer to MDE-4354 Setting Up Metrologic
Note: Your bar code scanner has been programmed with default settings at the factory and
Table of Contents
Topic
Introduction
Important Safety Information
Setting Up the Scanner
Programming a Sequence
Bar Codes
MDE-4631 Metrologic® MS7120 Bar Code Scanner Setup · January 2007
IMPORTANT INFORMATION
Profit Point Terminal for Datalogic DLL2020 scanners.
Metrologic MS6720 scanners.
should be ready to be configured.
Metrologic
MS7120 Bar Code Scanner Setup
®
MS6720 Bar Code Scanner for
®
MDE-4631
January 2007
Page
1
3
5
7
8
Page 1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the MS7120 and is the answer not in the manual?

Questions and answers

Related Manuals for Metrologic MS7120

Summary of Contents for Metrologic MS7120

  • Page 1 Note: Your bar code scanner has been programmed with default settings at the factory and should be ready to be configured. Table of Contents Topic Page Introduction Important Safety Information Setting Up the Scanner Programming a Sequence Bar Codes MDE-4631 Metrologic® MS7120 Bar Code Scanner Setup · January 2007 Page 1...

  • Page 2: January

    Introduction Warranty For information on warranty, refer to MDE-4255 Gasboy’s Warranty Policy Statement. If you have any warranty-related questions, contact Gasboy’s Warranty Department at its Greensboro location. Page 2 MDE-4631 Metrologic® MS7120 Bar Code Scanner Setup · January 2007...

  • Page 3: Important Safety Information

    Fuels and their vapors will become explosive if ignited. Spilled or leaking fuels cause vapors. Even filling customer tanks will cause explosive vapors in the vicinity of dispenser or island. MDE-4631 Metrologic® MS7120 Bar Code Scanner Setup · January 2007 Page 3...
  • Page 4 IMPORTANT: Oxygen may be needed at scene if gasoline - Electrical Hazards, 29 CFR Part 1910.333 contains specific has been ingested or inhaled. Seek medical advice Lockout/Tagout provision for electrical hazards. immediately. Page 4 MDE-4631 Metrologic® MS7120 Bar Code Scanner Setup · January 2007...

  • Page 5: Setting Up The Scanner

    Turn off power to the Profit Point Point of Sale (POS) terminal. Unplug the AC power to the POS Distribution Box (D-Box) power supply. Remove the scanner and the Metrologic cable from the shipping box. Note: None of the other parts in the shipping box, including the scanner power transformer, will be used with this installation.
  • Page 6 Note: The first time the scanner is turned on, the first scan may produce the error message “Data Error on Scanner Port” even if the scanner is programmed correctly. Page 6 MDE-4631 Metrologic® MS7120 Bar Code Scanner Setup · January 2007...

  • Page 7: Programming A Sequence

    Figure 14 on page use the 00-02407 Configuration Guide. Note: A PDF version of 00-02407 Metrologic Instruments, Inc. MetroSelect Configuration Guide is available at the following URL: ftp://ftp.metrologic.com/pub/download/productmanuals/00-02407.pdf Exit the program mode by scanning in the bar code in Figure 14 on page The scanner should now be properly programmed.

  • Page 8: Bar Codes

    Bar Codes Bar Codes Figure 2: Enable RS-232 Mode Note: Refer to page G1 in the 00-02407 Metrologic Instruments Inc. MetroSelect Configuration Guide, if necessary. Figure 3: Space Parity CAUTION Use only for Profit Point PLUS systems. Note: Refer to page G2 in the 00-02407 Metrologic Instruments Inc. MetroSelect Configuration Guide, if necessary.
  • Page 9 Figure 4: No Parity CAUTION Use only for NT Profit Point and DOS Profit Point systems. Note: Refer to page G2 in the 00-02407 Metrologic Instruments Inc. MetroSelect Configuration Guide, if necessary. Figure 5: Set 9600 Baud Rate CAUTION Use only for Profit Point PLUS systems.
  • Page 10 Figure 6: Set 1200 Baud Rate CAUTION Use only for NT Profit Point and DOS Profit Point systems. Note: Refer to page G4 in the 00-02407 Metrologic Instruments Inc. MetroSelect Configuration Guide, if necessary. Figure 7: Set to 7 Data Bits CAUTION Use only for Profit Point PLUS systems.
  • Page 11 Figure 8: Set to 8 Data Bits CAUTION Use only for NT Profit Point and DOS Profit Point systems. Note: Refer to page G5 in the 00-02407 Metrologic Instruments Inc. MetroSelect Configuration Guide, if necessary. Figure 9: Set to 1 Stop Bit CAUTION Use only for NT Profit Point and DOS Profit Point systems.
  • Page 12 Bar Codes Figure 10: Disable RTS/CTS Handshaking Note: Refer to page G6 in the 00-02407 Metrologic Instruments Inc. MetroSelect Configuration Guide, if necessary. Figure 11: Disable XON/XOFF Handshaking CAUTION Use only for Profit Point PLUS systems. Note: Refer to page G9 in the 00-02407 Metrologic Instruments Inc. MetroSelect Configuration Guide, if necessary.
  • Page 13 Figure 12: Enable CR Suffix CAUTION Use only for NT Profit Point and DOS Profit Point systems. Note: Refer to page E14 in the 00-02407 Metrologic Instruments Inc. MetroSelect Configuration Guide, if necessary. Figure 13: Expand UPC-E to 12 Digits CAUTION Use only for NT Profit Point and DOS Profit Point systems.
  • Page 14 Bar Codes Figure 14: Enter/Exit Configuration Mode Note: Refer to page x (10) in the 00-02407 Metrologic Instruments Inc. MetroSelect Configuration Guide, if necessary. Datalogic is a trademark of Datalogic S.p.A. Metrologic and MetroSelect are registered trademarks of Metrologic Instruments Inc.

Table of Contents