Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Upper Bounce UBRTG01-1017
Summary of Contents for Upper Bounce UBRTG01-1017
- Page 1 UBRTG01-1017 Manual Version #01...
- Page 3 INTRODUCTION must...
- Page 4 TRAMPOLINE GUIDELINES...
- Page 5 24 ft...
- Page 8 TRAMPOLINE PARTS LIST FOR UBRTG01-1017 TOP RAIL A UBRPTR1-1017 UBRPTR2-1017 TOP RAIL B UBRPTR3-1017 UBRPCT1-1017 CORNER TUBE UBRPCT2-1017 UBRPLE-1017 EXTENSION LEG BASE UBRPL1-1017 JUMPING UBRPM-1017 COVER UBRPP-1017 PADS SPRINGS UBHWD-SP-7.5-15 TOP RAIL SCREWS UBRPRS-1017 & NUTS LEG BASE UBRPSW-1017 SCREWS...
- Page 9 Frame assembly installation for model UBRTG01-1017 Attach the leg extensions to the leg base and tightly secure together with screws and washers Part #J and K. Continue doing the same to all 4 leg bases. 2. Connect the middle leg supports to the legs.
- Page 10 5. Assemble frame parts B1 and B2 with the 4 legs. Lay out the parts as shown in the figure. Connect the B1 and B2 and place it onto the leg bases as shown in the figure below. Note: 1. The Part #A goes on the long side of the trampoline - the 17 ft side. 2.
- Page 11 1. Layout the Trampoline Mat inside the frame. 2. Connect all 4 corners spring to corner top rail.
- Page 12 The pad has a few sets of strings with S shaped hooks at the end, all around the pad. Attach the S Shape hooks to the v-rings of the mat. Attach the hooks from underneath the mat. Refer to the figure at the side.
- Page 13 ENCLOSURE PARTS LIST 1017 PLASTIC CAP UBRPPC-814,915,1017 ON THE HOLE UPPER POLE UBRPUP-814,915,1017 WITH FOAM 38.2’’ LOWER POLE UBRPLP-814,915,1017 WITH FOAM 39.4’’ UBRPFG3-1017 26’’ FIBERGLASS UBRPFG1-1017 ROAD 39.4’’ UBRPFG2-1017 33.5’’ SAFTEY ENCLOSURE NET UBRPPS-814,915,1017 POLE SCREW PVC SLEEVE UBRPRS-1017 WRENCH FIBER GLASS UBRPCC-1017 CORNERS...
- Page 14 Connect the lower poles to the upper poles, connect it to the straighter part of the upper pole. Secure it together with screws at the point where it connects. Make sure the EPE foams are covering the poles. Connect the fiber glass pieces together, using 5 pcs of fiber glass to make the long line, and 3 pcs to make the short line.
- Page 15 Insert the fiber glass into the the sleeve of the safety net. Long fiberglass for long side, short for shorter side as explained in the previous step. After inserting the fiber glass into the sleeve of the enclosure net, both the long side and short side, connect the shorter side to the longer side with the corner pieces - Part #J.
- Page 16 11. You can skip step 10 and connect the net to the V-rings with the clips. We always recommend to use the ropes for extra stability. 12. Your trampoline now looks like this. Proceed to Testing the Trampoline section of this manual before jumping on the trampoline.
- Page 17 TESTING THE TRAMPOLINE...
- Page 18 FUNDAMENTAL BOUNCES TECHNIQUES...
- Page 19 Trampoline Anchor Kit (Set of 4) UBHWD-AK-4 Deep Fastening Spiraled Anchor Kit- Set Of 4 UBHWD-AKB-4 Trampoline Spring Pull Tool (T-Hook) UBHWD-TH Upper bounce Trampoline Jumping Skate UB-TJB Springs UBHWD-SP-7-15 Economy Trampoline Weather Protection Cover, Fits for 9 x 15 FT. Rectangular Frames -Black UBWCRTG-159-BK 44 Inch Trampoline Pole Foam sleeves, fits for 1.5”...
Need help?
Do you have a question about the UBRTG01-1017 and is the answer not in the manual?
Questions and answers