Pakedge WK-2-C Quick Start Manual
  1. Manuals
  2. Brands
  3. Pakedge Manuals
  4. Wireless Access Point
  5. WK-2-C
  6. Quick start manual

Pakedge WK-2-C Quick Start Manual

802.11ac dual band access point
Hide thumbs Also See for WK-2-C:
Table of Contents

Advertisement

Quick Links

WK-2-C
802.11ac Dual Band Access Point
QUICK START GUIDE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WK-2-C and is the answer not in the manual?

Questions and answers

Related Manuals for Pakedge WK-2-C

Summary of Contents for Pakedge WK-2-C

  • Page 1 WK-2-C 802.11ac Dual Band Access Point QUICK START GUIDE...

  • Page 2: Package Contents

    • 2 LAN ports for network extensions System requirements • Windows or Mac PC with an Ethernet interface WK-2-C default settings • Operation Mode: Access Point • IP Address: IP will be automatically assigned by router if a DHCP server is detected or, if no DHCP server is detected, the default IP address will be automatically set to 192.168.1.250.
  • Page 3 WK-2-C mounting 1 Open the release latch and press on the back of the device to swing the WAP out from the ceiling or wall bracket, then swing the WAP down.
  • Page 4 2 Using the supplied template, cut a 9.125” diameter circle at the desired mounting location for your WK-2-C. Route an in-wall Ethernet cable through the opening on the back of the WK-2-C housing, then insert the WK-2-C into the ceiling or wall. 3 Use a Phillips screwdriver to tighten the mounting ears.
  • Page 5 4 Plug the Ethernet cable into the WK-2-C, then route the cable cable as shown. (Use the optional cable clip, if necessary.) Then, swing the WAP back into the WK-2-C housing.
  • Page 6 WK-2-C installation with optional pre-construction bracket Pre-construction bracket sold separately. 1 Place the pre-construction bracket against the bottom of the ceiling studs at the desired mounting location. 2 Mark locations for mounting screws. Drill 1/16” pilot holes at marked locations. Secure the pre-construction bracket to ceiling studs using the provided hardware.

  • Page 7: Powering Up The Access Point

    The access point should now be up and running with its default settings. It does not need to be configured to be functional. To make changes to the SSID and security settings, you need to access the WK-2-C using a web browser.

  • Page 8: Logging In To The Access Point

    The following page will display when logged in: Note: If your computer is not set to the default IP scheme of the WK-2-C (192.168.1.X), you must first configure the TCP/IP settings on your computer to log in through a web browser.

  • Page 9: Configuring The Access Point

    Configuring the access point In this section, you can change the SSID name by applying the security profile that was set up in the Security Profiles tab. By default, the SSID is Pakedge2.4-1 and Pakedge5-1. You will have the option to change the Wireless Name (SSID) and add security profiles by selecting the options from the drop-down menu.

  • Page 10: Technical Support

    (650) 385-8703 For non-technical inquires: customerservice@pakedge.com (650) 385-8701 For regulatory information: www.pakedge.com/regulatory 11734 S. Election Road Draper, UT 84020 Main: (650) 385-8700 Fax: (650) 685-5520 www.pakedge.com sales@pakedge.com DOC-00182-A 2016-11-03 MS ©2016 Pakedge Device & Software Inc. All rights reserved.

Table of Contents