Nice IT4WIFI Instructions And Warnings For Installation And Use
Bust4 interface - wi-fi
Hide thumbs
Also See for IT4WIFI:
Related Manuals for Nice IT4WIFI
Summary of Contents for Nice IT4WIFI
- Page 1 Nice IT4WIFI BusT4 interface - Wi-Fi EN - Instructions and warnings for installation and use...
-
Page 3: Table Of Contents
CONTENTS GENERAL WARNINGS: SAFETY - INSTALLATION - USE 1 - PRODUCT DESCRIPTION AND INTENDED USE 2 - INSTALLATION 3 - OPERATING TECHNOLOGY 4 - INITIAL SET-UP 4.1 - Initial set-up with HomeKit technology using the “MyNice Welcome HK” app 4.2 - Initial set-up with MyNice (Android) technology 4.3 - Initial set-up with MyNice (iOS) technology 5 - HOMEKIT TECHNOLOGY 5.1 - Main functions of the “MyNice Welcome HK”... -
Page 4: General Warnings: Safety - Installation - Use
CAUTION During device installation, always strictly observe all instructions in this manual. In case of doubts of any nature, do not proceed with the installation and contact the Nice Technical Assistance Service for clarifications. CAUTION Important: keep these instructions in a safe place to enable future product maintenance and disposal operations. -
Page 5: Product Description And Intended Use
CAUTION! – Any use other than that specified herein or in environmental conditions other than those stated in this manual is to be considered improper and is strictly forbidden! The IT4WIFI accessory is a device that – by means of Wi-Fi communication – allows for controlling the movement and status of Gate&Door-type Nice automations compatible with the BusT4 (Opera) protocol. -
Page 6: Initial Set-Up
4.1 - Initial set-up with HomeKit technology using the “MyNice Welcome HK” app To run the procedure, you must be in the proximity of the IT4WIFI device, the L3 LED must be a steady green and the L2 LED flashing green. -
Page 7: Initial Set-Up With Mynice (Ios) Technology
4.3 - Initial set-up with MyNice (iOS) technology To run the procedure, you must be in the proximity of the IT4WIFI device, the L3 LED must be a steady green and the L2 LED flashing green. Should this not be the case, run the Reset procedure (Chapter 8). -
Page 8: Homekit Technology
5.1 - Main functions of the “MyNice Welcome HK” app Thanks to HomeKit technology, the “MyNice Welcome HK” app allows for the IT4WIFI accessory to be controlled, but not other HomeKit acti- vated accessories. This app also has the “Stop” control that other compatible HomeKit apps do not have: this allows the automation associated with IT4WIFI to be stopped in an intermediate position. -
Page 9: Other Functions
5.2 - Other functions It is also possible to use other functions that are not strictly linked to the “MyNice Welcome HK” app but that are compatible with the IT4WIFI Accessory; examples include: - Possibility to control Accessories and Scenes using Siri: with voice commands, such as “Open ... (Accessory name)”, “Close ... (Accessory name)”, “Scene ... -
Page 10: Mynice Technology
MYNICE TECHNOLOGY 6.1 - Main functions of the “MyNice Welcome” app Thanks to MyNice technology, the “MyNice Welcome” app allows for the IT4WIFI accessory to be controlled. The app manages two user types with an Administrator and User profile: - Administrator (by default, this is the first user who registers with the Accessory) can use all app functions... - Page 11 “Settings” > “WiFi” 02. Open the “MyNice Welcome” app: - if the app has no data recorded, select “Start with your first Nice Accessory”, enter “Username”, “Description”, “Home” - if the app already has data recorded, select “Settings”, then the Home and “Add Accessory…”...
-
Page 12: Ifttt Service
05. Enter the IFTTT app and enter your IFTTT account credentials 06. Find the “Nice” service and, once found, select “Connect” to connect your account to the service: paste the code generated by the “MyNice Welcome” app into the required field, then select “Authorize” and wait. -
Page 13: Reset
RESET Table 7 outlines the three types of hardware reset for the IT4WIFI Accessory. Table 7 Reset type Procedure • Full configuration reset 01. Hold the P key down (roughly 10 seconds) until all the LEDs (L1-L2-L3) begin to flash red Allows for all Accessory settings to be 02. - Page 14 Flashing orange Temporary The accessory is updating. Wait for the opera- (roughly 1 minute) tion to be completed. If the operation is not completed correctly, IT4WIFI automatically re- starts after 5 minutes Error status L1 LED L2 LED L3 LED...
-
Page 15: Troubleshooting
What to do if the IT4WIFI L2 LED remains orange when using MyNice technology? The Accessory does not have an active Nice Cloud connection. Check that the AP is connected to the Internet. Try to restart the Accessory if necessary (disconnecting it from the power and reconnecting it). -
Page 16: Ec Declaration Of Conformity
Declaration in accordance with Directive 1999/5/EC Note - The contents of this declaration correspond to that specified in the official document deposited at the Nice S.p.A. headquarters and, in particular, to the latest revised edition available prior to the publishing of this manual. The text herein has been re-edited for editorial purposes. A copy of the original declaration can be requested from Nice S.p.A. - Page 18 Nice S.p.A. Via Pezza Alta, 13 31046 Oderzo TV Italy www.niceforyou.com info@niceforyou.com...
Need help?
Do you have a question about the IT4WIFI and is the answer not in the manual?
Questions and answers