COVANA OASIS Installation Manual
With gazebo
Hide thumbs
Also See for OASIS:
- Owner's manual (81 pages) ,
- Installation manual (62 pages) ,
- User manual (32 pages)
Related Manuals for COVANA OASIS
Summary of Contents for COVANA OASIS
- Page 1 OASIS Read this manual before proceeding with installation Veuillez lire ce guide avant de procéder à l’installation Installation Manual Manuel d’installation www.covana.com...
- Page 2 FRANÇAIS La version française du manuel débute à la page 23.
- Page 3 THE REQUIREMENTS OF ALL APPLICABLE LOCAL CODES AND REGULATIONS. WARNING RISK OF ELECTROCUTION THE COVANA OPERATOR MUST BE CONNECTED TO A DEDICATED GFCI (GROUND FAULT CIRCUIT INTERRUPTERS) PROTECTED CIRCUIT. REFERENCE: MUST COMPLY WITH ALL APPLICABLE LOCAL CODES AND REGULATIONS. WARNING...
- Page 4 CONNECTIONS HAVE BEEN MADE. IMPORTANT ALL 4 POSTS OF THE COVANA MUST BE PROPERLY ANCHORED TO ITS FOUNDATION USING THE ANCHORING HOLES LOCATED AT THE FOOT OF EACH POSTS. THE OPTIONAL NON PERMANENT MOUNTING PLATES CAN BE USED WHEN ANCHORING IS NOT POSSIBLE.
- Page 5 REMOVE THE CONTROL KEY AFTER OPERATING THE COVANA. STORE THE KEY IN A SECURE LOCATION WHEN NOT IN USE. BRING THE KEY WITH YOU IN THE SPA TO PREVENT UNAUTHORIZED OPERATION OF THE COVANA. NOTICE The key switch must be permanently mounted and located 5 feet (1.5 m) away from the spa and 5 feet (1.5 m) above the...
- Page 6 1. Engineered wood deck OR concrete pad - 4" (10 cm) thick. 2. Each of the 4 posts on the Covana must be properly anchored to the foundation using at least one of the pre-drilled holes located at the foot of each post. Use a 1/4” (0.6 cm) concrete anchor for concrete pads or a 1/4”...
-
Page 7: Side Elevation Dimensions
SIDE ELEVATION DIMENSIONS 21" (53 cm) The maximum elevation height depends on the height of the spa. Add spa height to the Covana travel Covana maximum travel is to determine maximum elevation. 50" (1.27 m) Example: Spa height + Covana travel which is 50”... -
Page 8: Frame Dimensions And Footprint
FRAME DIMENSIONS AND FOOTPRINT... - Page 9 FRAME DIMENSIONS AND FOOTPRINT...
- Page 10 RISK OF INJURY DISCONNECT OR TURN OFF ALL POWER SUPPLY BEFORE STARTING ANY INTERVENTION ON THE COVANA. Remove the four screws on the bottom side of the Covana operator and take the cover off. Pre-wired key switch with 20’ (7,5 m) of cable in- cluded.
-
Page 11: Limit Switch Adjustment
Note: The UP & DOWN limits are factory adjusted and there is no need for re-adjustment. If adjustments are required to ensure the Covana roof does not come into contact with its sur- roundings while elevating, the UP direction may be decreased. Never change the factory set- tings of the DOWN limits or increase the UP limit. - Page 12 WARNING RISK OF INJURY DISCONNECT OR TURN OFF ALL POWER SUPPLY BEFORE STARTING ANY INTERVENTION ON THE COVANA. Disconnect or turn power off. Remove the four screws at the bottom of the operator and take the cover off. Use 1/2" or 1.3 cm hexagon socket wrench to operate the operator by turning the input shaft.
- Page 13 WIRING & SCHEMATIC DIAGRAM - 120VAC, 60HZ OPERATOR (NORTH AMERICA)
- Page 14 WIRING & SCHEMATIC DIAGRAM - 220VAC, 50HZ OPERATOR (EUROPE)
-
Page 15: Installation
If any damage is discovered, call Covana customer service at 1-877-278-8010. Stand the Covana in the vertical position. Ensure wind conditions allow for this to be done safely. Remove the parts box, the foams and the seals package from the crate and place them in a safe place. - Page 16 Use the 3/8'' Imperial wrench to unscrew the screws Use the Robertson screwdriver to unscrew the four holding the bottom of the jack – one (1) screw per (4) screws on the aspenite sheet at the bottom of the crate – one (1) sheet per side. side.
- Page 17 – four (4) screws per side. Place and center the roof of the Covana on the spa, pay attention to the short side and long side. The light switch, if a LED light kit option is installed in the cover, should be placed on the entry side of the spa.
-
Page 18: Lighting Installation
a 3/4” wrench on the square shaft at the bottom of Determine the corner of the Covana that is likely to receive the most sun, generally south is best; ensure the jack, make fine adjustments so it is in line with there are no interfering objects. - Page 19 Outside installation – Remove the solar panel from the box located inside the top of the Covana. Connect the solar panel to the lighting wire harness and place the wires and panel to the corner of the Covana where the panel will be mounted.
-
Page 20: Final Assembly
Verify that all four corner brackets are positioned at the same height. FINAL ASSEMBLY AT THIS POINT, THE ELECTRICAL POWER SUPPLY MUST BE CONNECTED TO CONTINUE THE INSTALLATION. THIS WILL ENSURE THE PROPER SETTINGS CAN BE MADE. Mount key box as per instructions on page 4. Then, using the self drilling screws, insert four screws per post. - Page 21 Readjust the corner brackets if contact is not made. Each of the 4 posts on the Covana must be properly anchored to the foundation using at least one of the pre-drilled holes located on the foot of each post.
- Page 22 Once the Covana has been fully assembled, elevate the cover using the key switch and remove the foam spacers. Lower the cover, walk around the entire perimeter of the spa observing where the white inside shell makes contact with the spa.
- Page 23 Made in Canada by Canimex www.covana.com PATENTED CANADA 2,532,429 US 11/162,557 UK 0515168.3 AUSTRALIA 2006200251...
Need help?
Do you have a question about the OASIS and is the answer not in the manual?
Questions and answers