Table Of Contents - Sony CFD-E10 Service Manual

CFD-E10

TABLE OF CONTENTS

1. GENERAL
·········································································· 3
2. DISASSEMBLY
································································ 4
2-1. Cabinet Front Assy, Cabinet Rear Assy ························· 4
2-2. TU Board, AUDIO Board ·············································· 5
2-3. LCD Board ···································································· 5
2-4. CD Lid Assy ·································································· 6
2-5. CD Holder ····································································· 6
2-6. CD Board ······································································· 7
2-7. Optical Pick-up (KSM-900AMA) ································· 7
2-8. Optical Pick-up (KSS-900A) ········································· 8
3. ELECTRICAL ADJUSTMENTS
4. DIAGRAMS
······································································ 11
4-1. IC Pin Function Description ········································ 12
4-2. Block Diagram ···························································· 13
4-3. Printed Wiring Board - TUNER Section - ················ 14
4-4. Schematic Diagram - TUNER Section - ··················· 15
4-5. Printed Wiring Board - CD Section - ························ 16
4-6. Schematic Diagram - CD Section (1/2) - ·················· 17
4-7. Schematic Diagram - CD Section (2/2) - ·················· 18
4-8. Printed Wiring Board - AUDIO Section - ················· 19
4-9. Schematic Diagram - AUDIO Section - ···················· 20
5. EXPLODED VIEWS
······················································ 23
5-1. Cabinet Front/Rear Section ········································· 23
5-2. Cabinet Center Section ················································ 24
5-3. CD Holder Section ······················································ 25
5-4. Optical Pick-up Section (KSM-900AMA) ·················· 26
6. ELECTRICAL PARTS LIST
2
································· 9
······································· 27
This appliance is classified as a CLASS 1 LASER product.
The CLASS 1 LASER PRODUCT MARKING is located on
the rear exterior.
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
NOTES ON HANDLING THE OPTICAL PICK-UP
BLOCK OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.
On AC power adaptor
• Use only the AC power adaptor supplied or
recommended in "Accessories (supplied/
optional)." Do not use any other AC power
adaptor. It may cause a malfunction.
Polarity of the plug
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.