Related Manuals for Zennio MAXinBOX
Summary of Contents for Zennio MAXinBOX
- Page 1 MAXinBOX SHUTTER 4CH / 8CH 4-Channel / 8-Channel Shutter Actuator ZIO-MBSHU4 ZIO-MBSHU8 Application program version: [1.0] User manual edition: [1.0]_a www.zennio.com...
-
Page 2: Table Of Contents
MAXinBOX SHUTTER 4CH / 8CH CONTENTS Contents ............................2 Introduction .......................... 3 1.1 MAXinBOX SHUTTER 4CH / 8CH ..................3 1.2 Installation ........................4 1.3 Start-Up and Power Loss ....................5 Configuration......................... 6 2.1 General ..........................6 ETS Parameterisation ....................6 2.2 Outputs.......................... -
Page 3: Introduction
MAXinBOX SHUTTER 4CH / 8CH 1 INTRODUCTION 1.1 MAXINBOX SHUTTER 4CH / 8CH MAXinBOX SHUTTER 4CH and MAXinBOX SHUTTER 8CH from Zennio are KNX specific actuators (of 4 or 8 channels, respectively) for controlling motorised shutter / blind systems. The most outstanding features are: 8 / 16 relay outputs, configurable as up to 4 / 8 independent shutter channels (with or without slats). -
Page 4: Installation
MAXinBOX SHUTTER 4CH / 8CH 1.2 INSTALLATION MAXinBOX SHUTTER 4CH / 8CH connects to the KNX bus through the on-board KNX connector. Once the device is provided with power from the KNX bus, both the individual address and the associated application program may be downloaded. -
Page 5: Start-Up And Power Loss
MAXinBOX SHUTTER 4CH / 8CH Manual control pushbuttons (6): pushbuttons for a direct control of the shutter channels during the set-up process. See section 2.2.1. To get detailed information about the technical features of this device, as well as on the... -
Page 6: Configuration
MAXinBOX SHUTTER 4CH / 8CH 2 CONFIGURATION 2.1 GENERAL After importing the corresponding database in ETS and adding the device into the topology of the desired project, the configuration process begins by right-clicking into the device and selecting Edit parameters. -
Page 7: Outputs
MAXinBOX SHUTTER 4CH / 8CH 2.2 OUTPUTS MAXinBOX SHUTTER 4CH / 8CH incorporates 8 or 16 relay outputs, respectively, configurable as up to 4 or 8 independent shutter channels, each of which will operate one motorised shutter system. For detailed information about the functionality and the configuration of the parameters related to the shutter channels, please refer to the specific manual “Shutter channels... - Page 8 MAXinBOX SHUTTER 4CH / 8CH Test Off Mode Under the Test Off Mode, the shutter channels can be controlled through both their communication objects and the actual pushbuttons located on the top of the device. When one of these buttons is pressed, the shutter will behave as if an order had been received through the corresponding communication object, and will also send the status objects when required.
-
Page 9: Ets Parameterisation
MAXinBOX SHUTTER 4CH / 8CH Note: due to the actions that may have been performed during the Test On mode, the device will ignore the real status of the shutter when the user leaves such mode. Therefore, the Test On mode is useful to synchronise the device status and the actual status of the shutter.. - Page 10 MAXinBOX SHUTTER 4CH / 8CH the manual control in runtime. When this checkbox is enabled, object “Manual Control Lock” turns visible, as well as two more parameters: Value: defines whether the manual control lock/unlock should take place respectively upon the reception (through the aforementioned object) of values “0”...
-
Page 11: Logic Functions
KNX bus, and to send the results through other communication objects specifically enabled for this purpose. MAXinBOX SHUTTER 4CH / 8CH can implement up to 20 different and independent functions, each of them entirely customisable and consisting in up to 4 consecutive operations each one. -
Page 12: Scene Temporisation
MAXinBOX SHUTTER 4CH / 8CH 2.4 SCENE TEMPORISATION The scene temporisation allows imposing delays over the scenes of the shutter channels. These delays, defined in parameters, are applied on the execution of one or more scenes that may have been configured. - Page 13 MAXinBOX SHUTTER 4CH / 8CH Therefore, parameter “Scene m. Channel z Delay” defines the delay that will be applied to the action defined in channel z for the execution of scene m. The range of this delay is 0 to 3600 seconds, 0 to 1440 minutes or 0 to 24 hours.
-
Page 14: Annex I. Communication Objects
“Functional range” shows the values that, with independence of any other values permitted by the bus according to the object size, may be of any use or have a particular meaning because of the specifications or restrictions from both the KNX standard or the application program itself. Only applies to MAXinBOX SHUTTER 8CH Number... - Page 15 MAXinBOX SHUTTER 4CH / 8CH 97, 114, 131, 148, , 182 1 Bit C - - W - DPT_UpDown [Cx] Move 0=Raise; 1=Lower , 216 98, 115, 132, 149, 1 Bit C - - W - DPT_Step [Cx] Stop/Step 0=Stop/StepUp; 1=Stop/StepDown...
- Page 16 MAXinBOX SHUTTER 4CH / 8CH 110, 127, 144, 161, , 195 1 Bit C - - W - DPT_Trigger [Cx] Direct Positioning 0=No Action; 1=Go to Position , 229 111, 128, 145, 162, , 196 1 Bit C - - W -...
- Page 17 Join and send us your inquiries about Zennio devices: http://zennioenglish.zendesk.com Zennio Avance y Tecnología S.L. C/ Río Jarama, 132. Nave P-8.11 45007 Toledo (Spain). Tel. +34 925 232 002. Fax. +34 925 337 310. www.zennio.com info@zennio.com...
Need help?
Do you have a question about the MAXinBOX and is the answer not in the manual?
Questions and answers