Remote Control (Vsx-609Rds) - Pioneer VSX-609RDS Operating Instructions Manual

Displays & Controls

Remote Control (VSX-609RDS)

DVD/LD TV/SAT VCR/DVR
1
RECEIVER TUNER
2
2
DSP MODE MIDNIGHT 5.1CH
1
CHANNEL
SELECT
3
5
CHANNEL
LEVEL
9
4
VOL
ST
5
MENU
SOURCE CLASS
6
D.ACCESS
7
1
LOUDNESS FUNCTION MUTING
8
9
RECEIVER
0
AUDIO/VIDEO PRE-PROGRAMMED
REMOTE CONTROL UNIT
-
1 MULTI CONTROL buttons
Use to put the receiver/remote control in the
stated mode.
For other equipment controls, see Controlling
the Rest of Your System on pages 52 – 55.
2 RECEIVER button (see page 15)
Use this button when setting up the surround
sound for the receiver.
3 Number/Mode buttons
(see pages 22, 43)
Use the number buttons to select the radio
frequency in tuner Direct access mode or the
tracks in CD, DVD mode etc.
Also, buttons marked with the following names
have special functions. If you try to use one of
these functions but the display flashes it means
that function cannot be used in the current mode
(for example DSP modes cannot be used when
5.1 CH setting is on).
2
(see pages 38, 39)
Use to put receiver in Dolby Digital, Dolby
Surround and DTS modes. To use first press the
RECEIVER button then operate this button.
32
En
=
Î
MULTI CONTROL
CD
CD-R/
TV CONT
TAPE/MD
2 3 4
TEST SIGNAL
ATT
TONE SELECT
6 7 8
EFFECT
~
0
10 DISC
CH
FUNC
TV CONTROL
VOL
FQ
!
ST
ENTER
TOP
MENU
@
FQ
MPX BAND
7 8 3
CHANNEL
#
DISPLAY RF ATT
¡ 4 ¢
$
%
FL REMOTE MASTER
DIMMER SETUP VOLUME
^
DSP MODE (see pages 39)
Use to put receiver in one of the DSP modes. To
use first press the RECEIVER button then operate
this button.
MIDNIGHT (see page 41)
Use to put receiver in Midnight mode. To use,
first press the RECEIVER button, then operate
this button.
5.1 CH (see page 40)
When the DVD/LD or DVD 5.1 CH function is
selected each press switches the DVD/LD input
between DVD/LD and DVD 5.1 CH. To use, first
press the RECEIVER button, then operate this
button.
CHANNEL SELECT (see page 21)
Use to select a speaker when setting up the
surround sound of the receiver. To use, first press
the RECEIVER button, then operate this button.
TEST TONE (see page 21)
Use to sound the TEST TONE when setting up
the surround sound of the receiver. To use, first
press the RECEIVER button, then operate this
button.
ATT
Use to attenunate (lower) the level of an analog
input signal and prevent distortion (refer to p.34
!, @). To use, first press the RECEIVER button,
then operate this button.
CHANNEL LEVEL +/– (see page 21)
Use to set up the levels of the surround sound of
the receiver. To use, first press the RECEIVER
button, then operate this button.
SIGNAL SELECT (see page 36)
Use to select the proper signal (analog, digital) for
the source your are inputting. To use, first press
the RECEIVER button, then operate this button.
4 TV CONTROL buttons
The following four sets of buttons are dedicated
TV controls.
FUNC button
Use to select the TV function.
button
Use to turn on the power of the TV.
CH +/– buttons
Use to change channels on your TV.
VOL +/– buttons
Use to adjust the volume on your TV.
5 MENU button
Use to access different menus associated with
your DVD player.