Advertisement
Quick Links
Wireless LAN & Bluetooth Module IC
For Mobile Phones, DSCs, PMPs and Gaming Devices
XP MFG Tool Command User Guide
Document
Date
release
Ver. 0.1
2011/07/05 Initial version
Ver. 0.2
2012/01/31 Add
AW-NM388
Version 0.2
Modification
Warning Statement
- 1 -
Initials
Approved
Lester Huang
Ivan Chen
Lester Huang
Ivan Chen
Advertisement
Related Manuals for AzureWave AW-NM388
Summary of Contents for AzureWave AW-NM388
- Page 1 AW-NM388 Wireless LAN & Bluetooth Module IC For Mobile Phones, DSCs, PMPs and Gaming Devices XP MFG Tool Command User Guide Version 0.2 Document Date Modification Initials Approved release Ver. 0.1 2011/07/05 Initial version Lester Huang Ivan Chen Ver. 0.2...
- Page 2 Figur1 When you test AW-NM388, AW-NM388 module put in socket and please connect the B type USB. It is necessary for two issues. One is for Bluetooth UART to USB interface control and the other one is apply the voltage for 32.768KHz OSC.
- Page 3 Figure 2 Figure 3 - 3 -...
- Page 4 (3) Connect SDIO to the host PC. (4) Choose “Cancel” for all auto hardware detection. (5) Install the 8787 SDIO driver following the steps below: 1. Refer to Figure 3 for the indication of the 8787 device in the Windows Device manager. 2.
- Page 5 Figure 5 Figure 6 - 5 -...
- Page 6 7. Setup Bluetooth UART to USB driver. FTDI IC is used in this adapter board. 8. Please indicated the install path to the FTDI folder (Check Azurewave FAE to get this one) 9. After installing, you can find the new comport showing up in the devices manager as figure 8.
- Page 7 Figure 8 1.2 Step2: Opening MFG Tool (1) Please make sure the AW-NM388 is enabling (check OS device manger). (2) Opening MFG tool, please double click on the “DutApiSDUART8787.exe.” in this sub folder: (3) \ MFG-8787-WIFI-SD-BT-SD-WIN-X86-1.2.6.22-14.0.3.p155\bin\labtool 1.3 Step3: Initial Command As the information showed on your screen, please enter these commands below to start your test.
- Page 8 Figure 9 1.3 Step3: Generate 802.11 b/g/n Packet (1)Command: Select WIFI Main Antenna: 69 90000200 40 69 90000208 0 69 9000020C 8 69 80002200 FFFF Select WIFI AUX Antenna: 69 90000200 400 69 90000208 0 69 9000020C 20 69 80002200 FFFF (2)Command: 22 1 12 1 22: Initial transmit power in the antenna 1: Set the wanted channel (1~14 for B/G/N mode)
- Page 9 (3)Command: 112 0 (only for N mode) 112: N mode HT20/40. 0: for HT20/40. 0HT20, 1HT40 (4)Command: 25 1 13 25: Set duty cycle, packet mode. 1: Data rate enable 13: Data rate set up A mode &B mode & G mode 1Mbps 5.5Mbps 11Mbps 6Mbps...
- Page 10 1.5 Step5: Test RX sensitivity Before test RX, the Marvell standard waveform is needed. Please contact Azurewave FAE for this issue. (1)Command: Select WIFI Main Antenna: 69 90000200 40 69 90000208 0 69 9000020C 8 69 80002200 FFFF Select WIFI AUX...
- Page 11 1.7 BT test mode Commands When you begin to test Bluetooth, please make sure your com port is correct. Please open the “setup.ini” file which is under: \ MFG-8787-WIFI-SD-BT-SD-WIN-X86-1.2.6.22-14.0.3.p155\bin\labtool As Figure 10. Figure 10 Find the BT COM port and make sure the com port is corresponding to the device manager. - 11 -...
- Page 12 As Figure 11. Figure 11 (1) Command 45Check BT MAC. (2) Command 78 1BT enter test mode. After you type above command, you can measure BT signal both TX/RX and the other BT test items by your BT instrument. - 12 -...
-
Page 13: Federal Communication Commission Interference Statement
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. -
Page 14: Industry Canada Statement
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. - Page 15 Radiation Exposure Statement: This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un environnement non contrôlé.
- Page 16 n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users.
- Page 17 équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire àl'établissement d'une communication satisfaisante. Le présent émetteur radio (IC: 6100A-NM388 / Modèle: AW-NM388) a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne.
- Page 18 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並 改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電 機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 本模組於取得認證後將依規定於模組本體標示審合格籤，並要求平台上標示「本產品內含射頻模 組：ID 編號」 - 18 -...
Need help?
Do you have a question about the AW-NM388 and is the answer not in the manual?
Questions and answers