Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Cleanflight Seriously Pro Racing F3 NEO
Summary of Contents for Cleanflight Seriously Pro Racing F3 NEO
- Page 1 SP Racing F3 NEO Flight Controller & Power Distribution Board + On-Screen Display & Video Transmitter FPV Stacking System Thank you for directly supporting the Cleanflight project with your purchase. Seriously Pro Racing F3 NEO Manual (Version 1) Copyright © 2016 Dominic Clifton...
-
Page 2: Features / Specification
The NEO system comprises of two boards, a bottom board with the FC/PDB and a top board with an OSD and VTX. The Cleanflight OSD software is all new and supports a variety of features with more to come. The USB socket on the FC allows configuration and firmware flashing via the cleanflight configurator. No additional software, other than drivers, is needed. - Page 3 Ensure you reference the manual that is appropriate to your firmware version. History The hardware was designed by the lead developer of Cleanflight to be the first brand-new open-source OSD sys- tem available to replace the ageing 8-bit MWOSD system and to pave the way for future OSD systems that build on the Cleanflight codebase.
-
Page 4: General Advice
• Once you have soldered pin headers in place DO NOT attempt to remove them unless you are highly skilled de-soldering and have the correct tools. Overheating the board or components will destroy it. SPRacingF3NEO http://seriouslypro.com - http://cleanflight.com Page 4... - Page 5 For connecting to the GND and 12V* pins on the OSD/VTX directly above the NEO. *See 12V/3S selector. 12V* BUZZER BUZZER 1 n BUZZER- (B-) For connecting to an active buzzer OR the BUZZER headers pins on the OSD/VTX directly above the NEO. BUZZER+ (B+) / 5v SPRacingF3NEO http://seriouslypro.com - http://cleanflight.com Page 5...
- Page 6 For connecting to the USART headers on the OSD/VTX directly above the NEO. 2 l RXD (R1) I2C/UART3/UART4 socket I2C/UART3/UART4 socket (14) Use this socket to connect a GPS receiver with I2C MAG and optional BARO sensors to use Cleanflight GPS features. IMPORTANT: The 3.3v signals 5.0v...
- Page 7 FC. Power the VTX module or External VTX can be controlled by the FC. It will be either ON or OFF. Cleanflight has a feature that allows a 5V VTX to be turned ON/OFF remotely.
-
Page 8: Installation Warning
NOTE: Do not solder the stacking pin sockets and pin headers into each board without the boards being connected and pressed together, otherwise the 12position stacking connector on the OSD/VTX will not be fully inserted into the NEO. FOLLOW THE INSTALLATION GUIDE SPRacingF3NEO http://seriouslypro.com - http://cleanflight.com Page 8... -
Page 9: Installation
The NEO is supplied with two recevier cables. The OSD is supplied with a 3 pin JST-ZH cables for camera connections. IMPORTANT: Ensure that you leave some slack in your cable routing as this will help if you crash your aircraft. SPRacingF3NEO http://seriouslypro.com - http://cleanflight.com Page 9... - Page 10 • Click connect, verify that communication is established. Disconnect and upgrade the firmware using the Cleanflight configurator tool. (See Firmware Upgrade section). For further software configuration see the Cleanflight manual. DFU driver installation. A DFU driver is required to flash the latest firmware.
-
Page 11: Firmware Upgrade
6. Click ‘Flash Firmware’. At this point the FC will reboot into DFU mode. DFU will appear in the list of ports and flashing via DFU will proceed. After flashing the virtual COM port will re-appear. IMPORTANT: Verify operation using latest CLEANFLIGHT firmware before attempting to use al- ternative firmware. Not all features may be supported by alternative firmware. - Page 12 Q: Unable to connect and a repeating light sequence occurs on the activity LED. A: Check the Cleanflight manual for how to interpret the error code (count the long flashes). Q: Unable to connect to the board (and status LED shows non-repeating pattern at boot-up).
-
Page 13: Hardware Specifications
Software support and contributions from many, many authors. For a complete list see github contributors. https://github.com/cleanflight/cleanflight/graphs/contributors Community Thanks to everyone from the AWESOME Cleanflight community for code, artwork, support, ideas, feedback, and everything else. Without you all this product would not exist. SPRacingF3NEO http://seriouslypro.com - http://cleanflight.com...
Need help?
Do you have a question about the Seriously Pro Racing F3 NEO and is the answer not in the manual?
Questions and answers