Related Manuals for Worx Landroid WR101SI
Summary of Contents for Worx Landroid WR101SI
- Page 3 Original instructions Installation guide...
- Page 4 ® How to install your Landroid The installation of the Landroid ® is easy. Depending on the size of your garden, the entire process only takes a short amount of time. If you are like us, you hate wasting your time to mow your lawn. The ®...
- Page 5 Preparation Before starting the installation read through this entire Installation Guide carefully. Drawing a sketch of the working area including all obstacles will make you easier to see the ideal positions for the charging base and where the boundary wires should be routed. In the box Charging base Landroid...
- Page 6 ® Landroid 's new home-your garden ® Let's start by having a closer look at Landroid ’s new home—your lawn—highlighting the areas where it can safely go and areas it’s best for Landroid ® to avoid. Obstacles that can be hit When hitting any obstacle that’s rigid, stable and taller than ®...
- Page 7 35% (20°) Slopes ® Your Landroid has the ability to safely climb slopes up to 35% (20°), so just avoid areas steeper than this. **How to calculate the slope of your lawn? 100cm Length 35cm Max. 35% slope So the slope would be: 35cm (Elevation) =35% (slope) 100cm (Length)
-
Page 8: Installation
Installation See details on step 2.3 26cm See details on step 2.1 26cm See details on step 2.2... - Page 9 26cm See details on step 2.4 26cm CHARGING BASE See details on step 1 & 3 >1m 26cm See details on step 2.7 10cm See details on step 2.5 26cm...
- Page 10 Your Landroid ® needs to know where to mow. This is why you have to mark its working area with a boundary wire ® that will form an invisible fence. This wire will also guide your Landroid to its charging base. ®...
- Page 11 Take off the cover on the charging base, you will see an IN-wire terminal (Black) and an OUT-wire terminal (Red). Strip the end of the boundary wire off to let the metal part expose, and connect the wire to the IN-wire terminal (Black) of the charging base. NOTE: The extended boundary wire should not be too long or it may cause signal problem.
- Page 12 2. Pegging Your Boundary Wire When pegging the boundary wire for the first time, it is recommended to use a normal lawn mower or a grass trimmer to cut the grass along the boundary. Then the wire can be laid as close as possible to the ground to prevent the Landroid ®...
- Page 13 A feature, such as flowers or shrubs that are close to the mowing boundary, should be excluded from the Landroid ® mowing area. 26cm If there is an island that sits inside your lawn where you don't ® want Landroid to go, please follow the path as shown in the diagram as you peg the wire.
- Page 14 In the case of two islands that are close to each other, it would be convenient to lay out the wire as illustrated in the picture. ® The Landroid can travel freely over the boundary wire in between the islands and the mowing boundary. >...
- Page 15 Completing the setup of the boundary wire Having outlined your garden with the boundary wire, you are now able to finish up the boundary wire setting. OUT WIRE IN WIRE Repeat Step 1.2 to lead the boundary wire to the charging base. Then cut the wire to a length that’s appropriate for reaching the terminal on the charging base, and strip the end of the boundary wire off.
- Page 16 Securing your charging base You can now permanently fix the charging base on the ground by tightening the supplied Base Fixing Nails with the supplied Hex key. 3. Connecting Your Charging Base to the Power Source When connecting the power cord of the charging base to the adaptor, align the notch on the power cord connector (b) with the groove on the adaptor connector (a).
- Page 17 LED light indicator Status Action Light does not turn on There is no power. Check if the power cord is connected properly to the charger and the charger is connected to a suitable power supply. Green light on Boundary wire is connected successfully;...
- Page 18 ® • If your Landroid ® • Landroid ® turns • If your Landroid ® • Your Landroid • Should your ® outside its territory, on, but the blade is inside its territory should always Landroid stop it will not move and disc does not but the LED error remain switched...
- Page 20 www.worxlandroid.com...
Need help?
Do you have a question about the Landroid WR101SI and is the answer not in the manual?
Questions and answers