Summary of Contents for Aspect LED AL-SL-WN-S-RGB
- Page 1 PROFESSIONAL GRADE LED LIGHTING www.aspectled.com Color Changing LED Strip Lights Installation Guide Copyright © 2012-2016. aspectLED, Inc.
- Page 2 LED Quantity: 9 LEDs per foot (150 per reel) Water-proofing Dimensions Input Voltage Cut Length 3/8” (10mm) wide 12VDC 4” (100.16mm) Non-waterproof 1/16” (2mm) thick AL-SL-WN-S-RGB 24VDC 6-1/2” (165.1mm) 16.4’ (5M) long 3/8” (10mm) wide 12VDC 4” (100.16mm) Water resistant AL-SL-WR-S-RGB 1/8” (3mm) thick 24VDC 6-1/2”...
- Page 3 Color Changing LED Strip Lights Installation Guide W-Series RGBW Ultra Bright Distance between LEDs: 1/2” (12mm) LED Quantity: 18 LEDs per foot (300 per reel) Water-proofing Dimensions Input Voltage Cut Length 1/2” (12mm) wide Non-waterproof 1/16” (2mm) thick 24VDC 6-1/2” (165.1mm) AL-SL-WN-U-RGBW 16.4’...
-
Page 4: Specifications
Color Changing LED Strip Lights Installation Guide SPECIFICATIONS Input Voltage 12VDC or 24VDC Power Consumption Model Dependent Ambient Temperature -40°F~140°F (-40°C~60°C) Beam Angle 120° 16.4 feet @ 12VDC Maximum Run 32 feet @ 24VDC TOOLS YOU’LL NEED Screw Driver Tape Measure Wire Stripper Scissors BEFORE YOU BEGIN... -
Page 5: Important Considerations
Color Changing LED Strip Lights Installation Guide It is important that you install this product (and all other electrical products) in accordance with the National Electric Code (NEC) and all applicable local building and electrical codes for your area. If you are unfamiliar with the NEC, your local building/electrical codes, and/or the proper installation methods for electrical devices, you should hire a qualified and licensed electrician to do the work for you. - Page 6 Color Changing LED Strip Lights Installation Guide STRIP LIGHT HANDLING Don’t bend LED strip light to a Don’t fold or crease LED strip light. Don’t tightly bend LED strip light diameter less than 1.5 inches. on a horizontal plane. Don’t apply excessive pressure to Never cover strip light with any Don’t power strip light while still surface of strip light.
-
Page 7: System Diagram
Color Changing LED Strip Lights Installation Guide SYSTEM DIAGRAM PLUG-IN ADAPTER SYSTEM DMX SYSTEM Copyright © 2012-2016. aspectLED, Inc. -
Page 8: Wiring Connections
Color Changing LED Strip Lights Installation Guide WIRING CONNECTIONS Only cut the strip on a marked cut line, these are located on the center of each set of copper soldering pads. INSTALLATION 1. Determine a suitable location to install the 3 components as labeled in System Diagram Controls Power Supply LED Light Fixture... - Page 9 Color Changing LED Strip Lights Installation Guide b. Verify that your strip light is acceptable for use in wet locations by looking for a “approved for wet location” label on the outside of the product packaging. Remember that only the strips are approved for wet locations (power supplies and connectors are not approved unless stated).
- Page 10 Color Changing LED Strip Lights Installation Guide a. When installing using the adhesive backing, press from one end to the other to prevent air pockets or raised sections. Be careful to limit contact with skin to ensure a minimal transfer of oil from skin to LED strip backing.
-
Page 11: Troubleshooting
Color Changing LED Strip Lights Installation Guide TROUBLESHOOTING Shift in brightness and/or • Make sure you did not exceed the maximum series run limit. This will cause temperature excess voltage drop, resulting in decreased brightness and/or temperature as the run is extended. Some lights are not •...
Need help?
Do you have a question about the AL-SL-WN-S-RGB and is the answer not in the manual?
Questions and answers