Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hello Kitty KT2015
Summary of Contents for Hello Kitty KT2015
- Page 1 2.4 GHz DIGITAL CORDLESS PHONE OWNER’S MANUAL KT2015 SUBSCRIPTION TO CALLER ID SERVICE FROM YOUR LOCAL TELEPHONE COMPANY IS REQUIRED FOR ALL CALLER ID FEATURES TO OPERATE CORRECTLY PLEASE READ AND FOLLOW THIS MANUAL BEFORE USING YOUR TELEPHONE AND KEEP IT FOR FUTURE REFERENCE...
-
Page 2: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS This symbol is to alert you the important operating or servicing instructions that may appear in your owner’s manual. Always follow basic safety precautions when using this product to reduce the risk of injury, fire or electric shock. When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire or electric shock and injury to persons including the following: Read and understand all instructions. -
Page 3: Fcc Information
16. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. 17. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. 18. Use caution when installing or modifying telephone lines. 19. -
Page 4: Fcc Rf Radiation Exposure Statement
circumstances. In the case of such temporary discontinuance, the telephone company shall promptly notify the customer who has the right to bring a complaint to the FCC if he feels the disconnection is not warranted. Interference Information -- USA This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference;... - Page 5 user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-
Page 6: Battery Cautionary Instructions
BATTERY CAUTIONARY INSTRUCTIONS CAUTION – To Reduce the Risk of Fire or injury to Persons, Read and Follow these instructions. 1. Risk of explosion if battery is replaced by an incorrect type. 2. Use only the supplied rechargeable battery pack: LEXEL, LH070-3A44C2BRML1P Ni-MH AAA 700mAh 2.4V Battery Pack. -
Page 7: Functions And Controls
INTRODUCTION TO CALLER ID INSTRUCTIONS Read this manual carefully before using this product and keep it for future reference. Congratulations on your purchase of this product! The unit allows you to take advantage of the Caller Identification service that may be offered by your local telephone company. Not all local telephone companies provide Caller Identification service therefore you must make sure the service is available. -
Page 8: Base Section
Base Section PAGE Page key IN USE In-use LED: The In-use LED will be steadily on during off-hook. During the period of incoming call, the In-use LED will also follow the ring cadence to go on or off. When registering, it will flash as a special cadence. -
Page 9: Getting Started
PHONE INSTALLATION INSTRUCTIONS Never install telephone wiring during a lightning storm. Never install telephone jacks in wet or damp locations. Never touch un-insulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying telephone lines. GETTING STARTED Connecting the Base Station and Power Plug Connect one end of the telephone line cord and the AC adaptor to the corresponding sockets in... -
Page 10: Installing Battery
Installing Battery Open the battery compartment by pushing the battery cover at the bottom hook. Insert the supplied rechargeable battery pack in the compartment, ensuring correct polarity. Place the upper hooks to the handset first and then push at the battery cover bottom to lock to close the battery cover. -
Page 11: Low Battery Warning
Low Battery Warning When the battery low condition is detected during standby mode, low-battery warning tone will sound and the empty battery sign is shown. L O W B A T T If, however, the low battery condition is detected when a call is active, a low-battery warning tone will sound every 15 seconds and the empty battery sign is shown. - Page 12 SUMMARY OF THE MENU FUNCTIONS For easy reference, all the selectable items are listed as follows: (Note: At any time, only one item is shown in the display) 1 - C A L L L O G 1 - U N R E A D 2 - M I S S E D 3 - R E C E I V E D 4 - C L E A R...
-
Page 13: Changing Language
CHANGING HANDSET SETTING Changing Language The default display language of the handset is English. Please follow the procedure below to change the display language if desired. 1. Select ‘LANGUAGE’ from the MENU by pressing [MENU/ ] 6 times and then press [INT / OK] to confirm selection. - Page 14 Changing Handset Name 1. You can change the Handset’s name displayed during standby mode by choosing sub-menu ‘HS NAME’ under HANDSET from the MENU. 2. If the handset name has been stored, the name will be displayed and can be changed. If no handset name was stored, if you like just key in your name using the key buttons and press [INT/OK] to complete.
- Page 15 CHANGING BASE SETTING Changing Base Ring Tone To change the base ringer volume, choose ‘VOLUME’ under ‘BASE’ in the MENU by pressing [MENU/ ] 4 times followed by [INT/OK]. 2. There are 5 selectable volume levels ranging from 0 to 5 levels and the base ring tone can be heard at the same time.
-
Page 16: Changing Flash Time
Changing Flash Time The flash time can be changed so that the base can be compatible to different PABX system. Choose ‘FLASH’ from the BASE setting menu and the current setting is displayed. 3 0 0 Three different flash times can be selected (100ms, 300ms or 600ms) To select the desired flash time, press [MENU/ ] or [ / Press [INT/OK] to confirm the selection. - Page 17 After entering the name and confirm, number entry will prompt. N U M B E R : You may enter a number of up to 16 digits. During number entry, press [C] to clear the last input digit if needed. 1 2 3 _ Press [INT/OK] to complete the number entry and also the procedure of storing an entry in the phone book.
-
Page 18: Caller Id Operation
CALLER ID OPERATION IMPORTANT: This function is operative only when your local telephone system offers Caller ID service and you have subscribed to it. You should consult with your telephone company if you have any questions about this service. PLACING A CALL NOTE: Before dialing, make sure that TONE or PULSE is chosen for your type of telephone service. -
Page 19: Pre-Dialing
Temp Tone Dialing You may want to change to Tone dialing temporarily during the call if the call has been setup for pulse dialing. This can be done by pressing [*/ ] key for more than 2 seconds during the call is active. A digit ‘d’... - Page 20 Dialing Number from the Phone Book Directory 1. To Dial the number stored in the phone book memory during standby mode, press [R/ the name for the first number stored in a sorted listed in the directory will appear in the LCD. A N G E L A To locate the desired entry either press [MENU/ ] [ / ] key or press [8 TUV] to locate the...
-
Page 21: Receiving A Call
RECEIVING A CALL Make sure the Caller ID service is turned on by your phone company. When receiving an external call, the handset and the Base will ring. The “EXT’ icon and the MSG (MESSAGE) LED will flash. Base In-use LED will flash according to the ring cadence. The caller’s number or name will be shown. -
Page 22: Display Screen Messages
Display Screen Messages If the network provider sends out CID information, some information will be shown. Sometimes, the service provider does not send out the number but provide reason of absence. The supported CID displays include: number absence, number, name absence, name, message indication and long distance indication. -
Page 23: Viewing Calls
Viewing Calls 1. The previous caller ID information can be read by choosing ‘CALL LOG’ from the MENU or by pressing the [ / ] key during standby to view the unread call. Notes: i. There are 3 kinds of CALL LOG entries: UNREAD, MISSED and RECEIVED. ii. -
Page 24: Deleting Message
Apart from the number can be stored, some ‘Absent reason’ will also be stored in the call log. Please see the examples below. 0 1 - B L O C K E D 0 2 - 1 1 2 5 6 6 8 0 3 - U N K N O W N 0 4 - J O H N 0 5 -... -
Page 25: Editing An Entry In The Phone Book
4. Press [INT/OK] and then that entry will be removed. 5. To delete all the phone book memory, choose ‘DELETE ALL’ under the CALL LOG. 6. Confirmation will be required for deleting all entries. C O N F I R M ? Press [INT/OK] to confirm the delete all procedure or press [C] to cancel. -
Page 26: Changing Volume
OTHER TELEPHONE FUNCTIONS Muting During Conversation During conversation (internal or external call), the microphone can be muted by pressing [ ]. After the function is selected, the icon will be on. 1 0 : 0 6 When the outgoing conversation is muted, you may press [ ] to un-mute the speech path. After that, the icon will be cleared. -
Page 27: Out Of Range Warning
Out of Range Warning When a handset is being off-hook and it is too far away from a base station, an out of range warning tone can be heard and handset will go to on hook. In idle mode, the range out tone will be heard every 30 seconds. -
Page 28: Troubleshooting Guide
TROUBLESHOOTING GUIDE PROBLEMS CHECK No dial tone Is any plug disconnected from all modular phone plugs? Is jack improperly wired? Phone does not work Are all cords connected properly? Phone does not ring The Ringer level may have been set to 0 ? Reset the Ringer level. -
Page 29: Consumer Information
CONSUMER INFORMATION This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA On the bottom of this equipment is a label that contains, among other information, a product identifier of US:DDKW400BKT2015. If requested, this number must be provided to the telephone company. -
Page 30: Care And Maintenance
CARE AND MAINTENANCE 1. Clean your phone with a damp (never wet) cloth. Solvent or detergent should never be used. 2. If your phone stops working, check to be certain that all modular plugs are properly “snapped” into their jacks. If the phone still doesn’t work and you have other telephones installed in your home, check to see if they are working.
Need help?
Do you have a question about the KT2015 and is the answer not in the manual?
Questions and answers