Table of Contents
Advertisement
Important: Retain these instructions
these instructions shall be used by trained service
personnel only.
If the equipment is used in a manner not
specifi ed by these instructions, the protection provided by the
equipment may be impaired.
ContEntS
1
Box contents ..................................................................1
2
Storing ...........................................................................1
3
Installation .....................................................................1
1
BoX ContEntS
3
InStAllAtIon
Dimensions
1
84 mm (3-5/16")
Note: Display and buttons only present on RD-WMB, not
RS-WMB.
RS-WMB, RD-WMB Installation Instructions TG201349 Issue 4, 26-Aug-2015. Applies to 1.02.2.
RS-WMB, RD-WMB Installation
Instructions (TG201349)
24 mm (15/16")
Installation Instructions
RS-WMB, RD-WMB
Room Display
GB
DE
DK
ES
PL
IT
NL
NO
https://partners.trendcontrols.com
4
Disposal .........................................................................8
5
Security .........................................................................8
2
StoRInG
-40 °C
+65.5 °C
(-40 °F)
(+150 °F)
H O
2
It is recommended that the installation should comply
with the local electrical safety installation practices (e.g.
HSE Memorandum of Guidance on Electricity at Work
Regulations 1989, USA National Electric Code).
Mounting Requirements
2
> 50 cm (1'6")
continued over page
FI
FR
SE
RU
0
95 %RH
1
Advertisement
Table of Contents
Related Manuals for TREND RD-WMB
Summary of Contents for TREND RD-WMB
- Page 1 Regulations 1989, USA National Electric Code). 84 mm (3-5/16”) Mounting Requirements > 50 cm (1’6”) 24 mm (15/16”) Note: Display and buttons only present on RD-WMB, not continued over page RS-WMB. RS-WMB, RD-WMB Installation Instructions TG201349 Issue 4, 26-Aug-2015. Applies to 1.02.2.
-
Page 2: Installation
Use No 6 screws 60 mm wall outlet box Use 3.5 mm screws UK pattress box Do not mount on a dry lining wall box as this prevents fl ush fi tting. RS-WMB, RD-WMB Installation Instructions TG201349 Issue 4, 26-Aug-2015. Applies to 1.02.2. -
Page 3: Installation Instructions
IQ4), the address may need to be changed (valid address range is 2 to 15). For RD-WMB it can be done using the Settings Menu - see step 12. For RS-WMB this must be done using the address switch. -
Page 4: Mode Description
Important: When using the strategy block (as explained 2 position fan (OFF, ON) above) some PVs write their value to the RD-WMB and will 3 position fan (OFF, ON, AUTO) overwrite changes to that PV made in the RD-WMB’s Settings 4 position fan (Off, 1, 2, 3) Menu. -
Page 5: Enter Settings Menu
0 0 0 0 NEXT ENTER ENTER PIN 0 0 0 0 NEXT ENTER ENTER PIN 0 0 0 0 NEXT ENTER ITEM ENTER PIN 0 0 0 0 value/setting NEXT ENTER RS-WMB, RD-WMB Installation Instructions TG201349 Issue 4, 26-Aug-2015. Applies to 1.02.2. - Page 6 Interface module in the strategy May need to be changed be if more FIRMWARE REV Read only than one device on wallbus. SETPOINT TYPE Can be set to the following: NUMERICAL GRAPHICAL RS-WMB, RD-WMB Installation Instructions TG201349 Issue 4, 26-Aug-2015. Applies to 1.02.2.
- Page 7 guration of the ‘Home’ display ‘More’ Display Check temperature 22.5 displayed Check humidity displayed Check CO concentration displayed Check outside 28.0 temperature ° is displayed Check change 22.0 setpoint is C ° displayed RS-WMB, RD-WMB Installation Instructions TG201349 Issue 4, 26-Aug-2015. Applies to 1.02.2.
-
Page 8: Check System
Division of Honeywell Technologies Sàrl, Z.A. La Pièce, 16, 1180 Rolle, Switzerland by its Authorized Representative, Trend Control Systems Limited. Trend Control Systems Limited reserves the right to revise this publication from time to time and make changes to the content hereof without obligation to notify any person of such revisions or changes.
Need help?
Do you have a question about the RD-WMB and is the answer not in the manual?
Questions and answers