Fuel Consumption (Mpg/Kpl); Koeo On Demand - Bosch OBD 1350 User Manual

en | 4 2 | User guide | OBD 1350 ProGrade OBDII Scan Tool
Since CAN vehicles use module IDs larger than 2 digits,
the scan tool assigns a 2 digit module ID to be used in
place of the actual CAN module ID. The module ID
assigned for the CAN module ID is used in all functions
of the scan tool.
• ISO 14230-4 protocol is shown as K2K (Keyword
2000).
Modules Present
ID Protocol
$10 K2K*
Press ENTER to continue
In the above examples, the * indicates the protocol used
to communicate to the vehicle's control module.
5.18

Fuel Consumption (MPG/KPL)

The Fuel Consumption function allows the scan tool to
provide information related to fuel consumption for your
current trip. This function is only supported on gasoline
burning vehicles using a Mass Airflow sensor (MAF). It
should not be used for diesel vehicles because the fuel
consumption will be totally inaccurate. This function
depends on the vehicle maintaining a 14.7:1 air/fuel
ratio. Diesel vehicles do not adhere to this ratio and that
is why this function can't be used.
From the Special Functions Menu:
1. Select Fuel Consumption(MPG/KPL) .
• Use the UP and
Consumption (MPG/KPL) is highlighted.
• Press .
Special Functions
Global OBDII Functions
Charging System Monitor
Fuel Consumption(MPG/KPL)
Acronyms
Review Data
Print Data
Code Lookup
System Setup
If the vehicle doesn't use a MAF, the scan tool will display
a message indicating that Fuel Consumption is not
supported.
Fuel Consumption(MPG/KPL)
PIDs required to calculate
Fuel Consumption not
supported by this vehicle
Press ENTER to continue
580001 | REV. A | 11.2016
DOWN keys until Fuel
2. The scan tool will now calculate Fuel Consumption.
Fuel Consumption(MPG/KPL)
Instantaneous(MPG)
Average(MPG)
Elapsed Time(H:M:S)
Distance(MI)
Fuel Used(GAL)
Average Speed(MPH)
Reset
Press the Reset key at any time to reset calculation back
to zero. Press the Metric key to change the units from
Miles per gallon to Kilometers per liter.
• Instantaneous – This is an average of fuel con-
sumed over the last 3 or 4 seconds. Instanta-
neous fuel consumption is only calculated while
the vehicle is moving.
• Average – This is the average fuel consumed
since the reset key was pressed or the fuel
consumption function was selected from the
menu.
• Elapsed Time – This is the total elapsed time in
(H)ours, (M)inutes, and (S)econds, since the
reset key was pressed or the fuel consumption
function was selected from the menu.
• Distance – This is the total distance driven,
since the reset key was pressed or the fuel
consumption function was selected from the
menu.
• Fuel Used – This is the total fuel used, since the
reset key was pressed or the fuel consumption
function was selected from the menu.
• Average Speed – This is the average vehicle
speed, since the reset key was pressed or the
fuel consumption function was selected from
the menu.
3. Return to Special Functions Menu.
• Press .
5.19

KOEO On Demand

The KOEO On Demand is a functional test of the Ford
computer modules and system with the KOEO. It tests
the inputs, outputs, and sensor ranges. Any faults or
DTCs are retrieved by the scan tool.
It is VERY IMPORTANT that each step be performed
when prompted by the scan tool. Failure to follow direc-
tions may set DTC(s).
From the On Demand Tests Menu:
1. Select KOEO On Demand .
• Use the UP and
On Demand is highlighted.
• Press .
36.8
28.8
39:35
33.4
1.11
50.6
Metric
DOWN keys until KOEO