Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Fourgroup DUPLEX-UP
Summary of Contents for Fourgroup DUPLEX-UP
- Page 1 Date : 10/02/14 Rev . 01 PR .T : FG006172 USE AND INSTALLATION HANDBOOK DUPLEX-UP CONTROL PANEL FOR 2 ELECTRIC PUMPS WITH CURRENT CONTROL . DUPLEX-UP Via Enrico Fermi 8 - 35020 Polverara PD Tel.049/9772407 Fax.049/9772289 www.fourgroup.it E-mail : info@fourgroup.it...
-
Page 2: Table Of Contents
INDEX Warnings page………3 Overview page ………4 Handling page ………4 Application and working limits page ……….5 Standard operations page ……….6 Installation page ……….7-8 Electrical connection page ……….9-10 Regulation and calibration page ……….11 Stop of the pumps page ……….12 Lights and push-buttons page ……….12 Maintenance page ……….13... -
Page 3: Warnings
1. WARNINGS The following symbols, accompanied by the words: “Danger”, “Warning”, indicate the potential hazard resulting from failure to observe the associated warning, as specified below: DANGER Failure to observe this warning may result in RISK OF ELECTRIC electric shock SHOCK Failure to observe this warning may cause DANGER... -
Page 4: Overview
PRELIMINARY INSPECTION: after you have removed the external packaging, visually inspect the control panel to make sure it has suffered no damage during shipping. If any damage is visible, inform a FOURGROUP dealer as soon as possible, no later than five days from the delivery date. -
Page 5: Application And Working Limits
RISK OF ELECTRIC WARNING SHOCK The DUPLEX-UP is designed for controlling two motors or electric pumps used in pressurization systems or in applications for emptying wells or water tanks with multi-contact float switches. FOURGROUP S.r.l. shall not be liable for any damage caused or suffered by the unit as a result of its unauthorised or improper use. -
Page 6: Standard Operations
5. STANDARD OPERATIONS DANGER RISK OF ELECTRIC DANGER WARNING SHOCK The “Mains power on” LED comes on to indicate that the board is functioning properly. The motor can be governed directly by the operator with man present (Manual) or by remote signals (Automatic) by means of the “Automatic –... -
Page 7: Installation
Connect the unit at ground before carrying out any other operation. The voltage input corresponds to the data written on the panel and on the pump. ( 400V ± 10% 50/60Hz x DUPLEX-UP-T ) ( 230V ± 10% 50/60Hz x DUPLEX-UP-M ). - Page 8 6b. INSTALLATION TO FIX THE CABLES IN THEIR TERMINALS USE A TOOL OF THE PROPER SIZE TO AVOID THE DAMAGING OF THE SCREWS OR OF THEIR SEAT. If use an electric screwier pay attention not to spoil the thread or the screws. FIX THE CONTROL PANEL TO A WALL AS IN PICTURE N.1 WITH SCREWS AND SCREW ANCHOR USING THE HOLES ARRANGED IN THE BOX OR THE FIXING BRACKET IF PRESENT.
-
Page 9: Electrical Connection
7a. ELECTRICAL CONNECTION DUPLEX-UP-T DANGER RISK OF ELECTRIC DANGER WARNING SHOCK AMPEROMETRIC PROTECTION CUT- IN DELAY TIME OVERRIDE JUMPERS AMPEROMETRIC - WITH JUMPER CONNECTED: TRANSFORMERS OVERLOAD TRIMMERS DELAY OVERRIDDEN PRIMARY LINE MOTOR COMMAND PROTECTION LINE PROTECTION FUSE FUSES (400 V) - Page 10 7b. ELECTRICAL CONNECTION DUPLEX-UP-M DANGER RISK OF ELECTRIC DANGER WARNING SHOCK AMPEROMETRIC PROTECTION CUT- IN DELAY TIME OVERRIDE JUMPERS AMPEROMETRIC - WITH JUMPER CONNECTED: TRANSFORMERS OVERLOAD TRIMMERS DELAY OVERRIDDEN PRIMARY LINE START MOTOR PROTECTION CAPACITOR PROTECTION CONNECTIONS FUSE FUSES (230 V)
-
Page 11: Regulation And Calibration
8a. REGULATION AND CALIBRATION Before the ignition the “System of Motor Protection from Overload” has to be calibrated setting the Current Protection on the internal regulator of the Board. The Protection Delay is set at a fix time of 4 seconds. During the calibration close the JUMPER “E.T.TA“... -
Page 12: Stop Of The Pumps
9. STOP OF THE PUMPS WARNING The MOTORS can be switched off in the following ways: - In “manual”, the motors stop when the “MANUAL” button is released; - In “automatic”, the motors stop when the FLOAT SWITCH are no longer enabled or when the current protection is actives, or by pushing the “0 –... -
Page 13: Maintenance
11. MAINTENANCE DANGER WARNING DUPLEX-UP does not require any routine maintenance provided that their working limits are observed. Any maintenance operations must be performed by qualified and experienced personnel, in compliance with the safety regulations in force. DANGER! Make sure that DUPLEX-UP is disconnected from the power supply before performing any maintenance operations. -
Page 14: Warranty
WE DECLINE all liability for damages and injury caused by our products. Fourgroup S.r.l. reserves the right to modify its products without notifications. Any controversy arising from the terms of this warranty shall be resolved in the Padua Court, even if payment is agreed by bank’s draft. -
Page 15: Conformity Declaration
15. CONFORMITY DECLARATION FOURGROUP S.r.l. with centre in Polverara via Enrico Fermi 8 – Padova – Italy, declare that the products DUPLEX-UP-T , DUPLEX-UP-M is in compliance with the following European directives and with the national directives of actuation : ... -
Page 16: Connection Diagrams
16. CONNECTION DIAGRAMS CONNECTIONS DUPLEX-UP-M CONNECTIONS DUPLEX-UP-T...
Need help?
Do you have a question about the DUPLEX-UP and is the answer not in the manual?
Questions and answers