Beijing Dahao Technology BECS-D56 Owner's Manual
  1. Manuals
  2. Brands
  3. Beijing Dahao Technology Manuals
  4. Sewing Machine
  5. BECS-D56
  6. Owner's manual

Beijing Dahao Technology BECS-D56 Owner's Manual

Computerized control system for embroidery machine
Hide thumbs
Table of Contents

Advertisement

Quick Links

刺绣机电脑
Computerized Control System for Embroidery
Machine
BECS-D56
（General Unit）
Version：2017-01
操作手册
OWNER'S MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the BECS-D56 and is the answer not in the manual?

Questions and answers

Summary of Contents for Beijing Dahao Technology BECS-D56

  • Page 1 刺绣机电脑 Computerized Control System for Embroidery Machine BECS-D56 （General Unit） Version：2017-01 操作手册 OWNER’S MANUAL...

  • Page 3: Table Of Contents

    4-12 “High speed design”...................... 47 4-13 Compile Packed Design ....................47 4-14 Create design from parameter ..................48 4-15 Move frame to make design ..................48 4-16 Create outline design from normal design ..............49 BECS-D56 computerized embroidery machine owner’s manual...
  • Page 4 Index 4-17 Copy design with varied switch length ................. 50 4-18 Design parameters operation ..................50 4-19 Import design from PC ....................51 4-20 Network Management Function ................... 52 Chapter 5 Management of Machine Parameters ................54 5-1 Normal Parameters ......................54 5.1.1 Design directions .......................
  • Page 5 Chapter 10 JF Type Sequin Embroidery ..................107 10-1 Brief Introduction on Sequin Embroidery ..............107 10-2 Embroider sequin ......................108 10-3 Input sequin design ..................... 108 10-4 Sequin design edition ....................109 10-5 Parameter about multi-sequin embroidery ..............113 BECS-D56 computerized embroidery machine owner’s manual...
  • Page 6 Appendix Ⅲ Error Information & Instruction of System Level Mistake ........ 163 Appendix Ⅳ Make Special Multi-Sequin Design ..............167 Appendix Ⅴ Network Connection of Embroidery Machines ..........178 All rights reserved. Beijing Dahao Technology Corp., Ltd. BECS- D56 computerized embroidery machine owner’s manual...

  • Page 7: Chapter 1 General Descriptions

    General Descriptions Thanks for using the Computerized Embroidery Control System produced by Beijing Dahao Technology Corp., Ltd. User are recommended to read this manual carefully, so as to operate the machine correctly and effectively. Besides, user should keep this manual for future use.
  • Page 8 Chapter 1 General Descriptions Overloading may cause serious loss. Please load according to the Compulsory instruction on the box.. Installation Don't jam the vent on the device. Don’t plug up the machine, or it may Caution cause fire or electronic shock. Make sure the installation direction is correct..

  • Page 9: Main Features

    5. Multi-Task Parallel and Free Shift among Tasks During embroidering, actions like design input & output, preparation for the following designs and modification of parameters can be carried out. Flexible shift among tasks can be realized by using the task-shifting key. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 10 Chapter 1 General Descriptions 6. Storage of Frequently Used Parameters and Color-Changing Order for Each Design Design will be saved along with its parameters, color-changing orders and needle bar colors. System can memorize the operational details for each design. Users can set parameters for a design during the embroidery process of the previous design, which will save time and improve the efficiency.
  • Page 11 The newly generated design can be used for embroidery, output or other operations. 20. Letter Design There are altogether 28 letter-bases. Users can make groups and change the letter order according to different tasks. This operation is simple and easy managing. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 12: Technical Specifications

    At the color changing point, user can either act color changing manually or let the system do according to the preset order automatically. 26. Special Embroidery BECS-D56 computerized embroidery has special embroidery functions (coiling, taping and Zigzag embroidery). 1-3 Technical Specifications 1.

  • Page 13: Chapter 2 Operation Instruction

    C. Direction in Using the USB Disk Please pay close attention to electrostatic phenomenon. Don’t forget to discharge before plugging in/out the USB disk. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 14: Instruction Of Control Panel

    Chapter 2 Operation Instruction USB disk features plug-in direction. Users should avoid plugging out during writing or loading data, because it may result in loss of data. We highly recommend users to check the data integrality in case of data missing. Note: During the process of USB format, sudden loss of electricity or plugging out the disk may break down the USB.
  • Page 15 Return to start point automatically After stop, user can press the manual frame-moving to move the frame (like applique), then press this button to have the Return to stop point frame return stop point automatically BECS-D56 computerized embroidery machine owner’s manual...
  • Page 16 Chapter 2 Operation Instruction Name Figure Description It is used for editing design or input needle number. They are used to select menu items or set Number keys parameters used for deleting the last letter you typed in It is used for manual moving or inputting Manual Moving point When user activates several interfaces, he can...

  • Page 17: Instruction Of The Main Screen

    Current status In embroidery confirmation status, you can pull bar to embroider. Embroidery preparation When machine stops, press this key status, user can confirm the to confirm to cancel confirmation embroidery status back preparation status BECS-D56 computerized embroidery machine owner’s manual...
  • Page 18 Chapter 2 Operation Instruction Name Figure Description System normal embroidery status. When you pull bar, the main shaft rotates and frame moves along the pattern trace. Pull bar to go back, machine Normal embroidery idles back in low speed. When machine stops, press this key to shift to low speed idling machine...
  • Page 19 Current Stitch Display current stitch Information information Color-changing Order Current stitch position Frame moving speed(use Machine status information to shift between low (In the order of speed high left to right, top to bottom) speed BECS-D56 computerized embroidery machine owner’s manual...

  • Page 20: Notes On Menu Status

    Chapter 2 Operation Instruction Name Figure Description Main shaft status(running stop in position , not stop in position Embroidery status（thread break 、 finish 、 color 、jump 、 changing ） pull bar to stop Cyclic embroidery , none cyclic embroidery Assistant embroidery status/ lockstitch/special...

  • Page 21: How To Input Numerals, Letters And Symbols

    The machine embroiders based on the designs in its memory. The following is the basic Procedure of Embroidery. 1. Input Designs 2. Choose a Design 3. Assistant Operations 4. Embroidery Confirmation 5. Pull the Bar for Embroidery 6. Cancel Embroidery 7. Manual Operation BECS-D56 computerized embroidery machine owner’s manual...
  • Page 22 Chapter 2 Operation Instruction A. Input Designs The user can import designs through network, floppy disk or USB disk. Only in status, can user transmit designs by PC network. For USB operation (disk operation), click the main screen to enter the “disk management” interface. You can also input designs by using in the design management interface.
  • Page 23 Attention: this function is to locate the design in the center of the frame area as preset in soft limit. If you want set soft limit area, press “ ” to enter assistant management menu. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 24 Chapter 2 Operation Instruction Save design start point —— click “ ” to enter the assistant operation screen in embroidery confirmation status. Attention: the function for saving and restoring the pattern start point is needed and the frame origin has been set in the system. If you want to set the origin point, click “...
  • Page 25 The user can manually turn the main shaft to 100° when it doesn’t reach there. Click “ ” in the main screen and then choose “ ” in the followed prompt to carry out the function. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 26 Chapter 2 Operation Instruction After the operation, the icon (main shaft not in the right position) will be replaced by (main shaft in the right position). Go to Start Point In the main screen click and choose “ ”in the followed prompt. Then the frame will return to the start point.

  • Page 27: Normal Embroidery, Returning And Mending

    The positioning idling can move the frame directly forwards (or backwards) to a designated position, or to the latest color-change position, or even to the latest stop-code position. In the BECS-D56 computerized embroidery machine owner’s manual...

  • Page 28: Operation Bar And Turn Shaft Button

    Chapter 2 Operation Instruction main screen, press “ ” to enter the interface of “Machine Parameter Management”. And then user can select forward/backward positioning idling by stitches, color change code or stop code. After the system returns to the main screen, user can pull the bar forward /backward to complete the positioning idling.

  • Page 29: System's Working Status

    In embroidery confirmation status ( is displayed), first press " " key. And then press “ ”key to release embroidery confirmation status. Now the machine enters preparation status ( is displayed). BECS-D56 computerized embroidery machine owner’s manual...

  • Page 30: Chapter 3 Disk Management

    Chapter 3 Disk Management Chapter 3 Disk Management In disk management, users can input the designs in the disk to machine, and vise versa; meanwhile, users can perform some common disk managing actions, like erasing file or catalogue, formatting disk, etc. Floppy disk (external device) and USB disk are both supported.
  • Page 31 Display the design files and folders of the File List disk in icons. It’s used to select files Show the total space and remaining space Disk space information information The current page and the total page Page information number BECS-D56 computerized embroidery machine owner’s manual...
  • Page 32 Chapter 3 Disk Management Number Icon Name Description Current route Display the shape of selected design and Preview of designs its information. Single- selection Switch between single- /Multi-selection selection and multi-selection Select all the items in the current Select all folder, only available...

  • Page 33: Design Preview

    At the same time the design’s peripheral information and color-changing number will be displayed. Note: User can select more than one design for preview. For selecting more than one design, please refer to chapter 3.3. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 34: Select One Or Several Designs

    Chapter 3 Disk Management 3-3 Select One or Several Designs Before preview, input and deletion of files, the objective design has to be selected firstly. The user can select one object at one time, or select several objects at one time to improve efficiency.

  • Page 35: Design Import

    1. Select one or more files in the disk 2. Click the design input key The system asks the customer to input design number and name for saving. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 36: Design Export

    Chapter 3 Disk Management 3. The user inputs the design number and name. The system provides the minimum available design number as the default value, when user enter the interface for inputting the memory design number and design name. The customer can use the small panel on the right to change the value.
  • Page 37 The method of modification is as same as that in “Design Import”. After the changing, press “ ” to save the result. 4. The system returns to the disk management screen and refreshes the list in current directory. During the above operation, you can press “ ” to exit. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 38: Directory Operation

    Chapter 3 Disk Management 3-6 Directory Operation 1. Enter the directory Select the directory and press “ ”. The system reads the item list of the directory and refreshes the screen. 2. Return to previous level Press the key “ ”...
  • Page 39 The system will begin to format the disk and show the speed with a process bar. After formatting, the system will display the prompt to show formatting success. Click the Return key to return to the disk management screen. Note: the system will format the disk in DOS format. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 40: Chapter 4 Memory Design Management

    Chapter 4 Memory Design Management Chapter 4 Memory Design Management Memory design management includes selecting embroidery designs, settings and transfer of designs and operations to create designs. 4-1 Memory Design Management Screen and Other Memory Design Operation Screens Click " "...
  • Page 41 Disk operation Please refer to Chapter 3 Copy the selected design Press this key to enter the design copy window Design edition Editing the current design or new design, please refer to chapter 8 BECS-D56 computerized embroidery machine owner’s manual...
  • Page 42 Chapter 4 Memory Design Management Number Icon Name Description Delete design Press this key to delete the current design Set applique design Press this key to set applique design Satin stitch compensation Set satin stitch compensation in memory design Packed design edition Press this key to enter into combined design editing Design division...

  • Page 43: Select One Or Several Designs

    5. After changing the design parameter, press “ ”to quit. User can use the selected design for embroidery. If the operation is completed, the system will close the memory design screen to return to the main screen. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 44: Design Preview

    Chapter 4 Memory Design Management 4-4 Design Preview The selected design can be previewed in the memory design preview screen according to the designated way. Number Icon Name Description Display the selected design on the Design preview area designated way and speed. Design information Display the design information.

  • Page 45: Copy The Memory Design

    If the user doesn’t want to change them, go to 6 directly. 4. To input a new design number, press “design number” and input the new number in the pop-up window, and then press “ ”to confirm the input. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 46: Delete The Memory Design

    Chapter 4 Memory Design Management 5. To input a new design name, press “design name” and input the new name in the pop-up window. 6. Press “ ”to confirm the input, carry out the copying operation and return to design operation selection interface.

  • Page 47: Add Applique Design

    ”in the main menu to enter the memory design management screen. 2. Select the design in the memory design image area of the memory design management screen. 3. Press “ ” to enter the screen to set applique displayed as below: BECS-D56 computerized embroidery machine owner’s manual...
  • Page 48 Chapter 4 Memory Design Management Number Name Description Design display Real-time display of the design when area machine embroiders to the applique point Sequence Show the sequence number of the number list position to set applique point. Stitch number Display the stitch number at that list position.

  • Page 49: Satin Stitch Compensation

    ” to adjust the satin width, save it as a new design and return to the design operation selecting screen. Press “ ”to cancel the setting and return to the design operation selecting screen. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 50: Edit Packed Design

    Chapter 4 Memory Design Management 4-9 Edit packed design The packed design (combined design) means a design group packed from certain memory designs(less than 99) after user sets their parameters. The packed design is set as automatic continuous embroidery. In the memory design management screen the icon of the packed design is displayed as .

  • Page 51: Design Division

    The action will divide one design into two designs at the pointed stitch. 1. Press the button “ ” on the main screen to enter the memory design management screen. 2. Select the design for operation. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 52: Combine The Designs

    Chapter 4 Memory Design Management 3. Press the key “ ” to enter the design division screen. 4. If you do not use the default value provided by the system, please input the design number, design name, division stitches by using the keyboard, then press “ ”...

  • Page 53: High Speed Design

    ” to enter screen for creating normal design from packed design. Input the new design number and name as required. 4. Press “ ”to save it or press “ ”to cancel the operation and return to the design operation selecting screen. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 54: Create Design From Parameter

    Chapter 4 Memory Design Management 4-14 Create design from parameter This is to change the setting of color-changing order and normal parameters such as scale and repetition, which is attached to a specific design, so as to create a new design. 1.

  • Page 55: Create Outline Design From Normal Design

    4. If user doesn’t use the default values, press “ ”and change them with keyboard. 5. Press “ ”to create an outline design and return to the design operation selecting screen. Press “ ”to cancel the operation and return. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 56: Copy Design With Varied Switch Length

    Chapter 4 Memory Design Management 4-17 Copy design with varied switch length This function is used to create the design with the same shape but the different stitch length. 1. Press “ ”in the main menu to enter the memory design management screen. 2.

  • Page 57: Import Design From Pc

    ” in the main menu to enter the memory design management screen. 2. Press “ ” and the screen will show as following. Input design number and name, press the key “ ” to start importing. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 58: Network Management Function

    Chapter 4 Memory Design Management After importing, system returns to the design management screen. Or press the key “ ”to cancel it. 4-20 Network Management Function The network management function enables to realize the remote real-time supervision on machine working status and batch download. 1.
  • Page 59 (2) Set the IP address of PC; (3) Set system IP, server address, port number and other parameters of embroidery machine computer. (4) Run server software EmbNetServer (5) Run the client software EmbClient BECS-D56 computerized embroidery machine owner’s manual...

  • Page 60: Chapter 5 Management Of Machine Parameters

    Chapter 5 Management of Machine Parameters Chapter 5 Management of Machine Parameters In this system each design has its own settings of the normal parameters (like scale and repetition) and color-changing order. When a new design is selected, the corresponding normal parameters and color-changing order that are saved with the design will become effective.

  • Page 61: Design Directions

    The user can make the design rotate in a certain angle with this parameter. 5.1.3 Setting of X-scale This parameter controls the scaling percentages in horizontal (X) direction, so as to scale up/down the design. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 62: Rep. Prior

    Chapter 5 Management of Machine Parameters 1. Press the option “X Scale” Press “X Scale” in the normal parameter screen, and the screen will show the parameter-setting window. 2. Set the parameter “X Scale” Press the number panel in the parameter-setting window to change the scaling ratio in X direction.

  • Page 63: Rep. Mode

    For setting the administrator passwords and the factory password, as well as initialization of parameters, please press “ ” to enter the “purview of machine parameter manage” screen. (See Chapter 5.4) BECS-D56 computerized embroidery machine owner’s manual...

  • Page 64: Setting Procedure For Other Parameters

    Chapter 5 Management of Machine Parameters Refer to the appendix one for description of each parameter. 1. Press “ ” in the main screen. 2. The system enters the parameter setting screen, and press “ ”set the parameters. Note:  The number, name and value of every parameter are displayed in the parameter list window.

  • Page 65: Introduction Of Functions In Other Parameters

    5.2.2 Introduction of Functions in Other Parameters There are brief introductions of the parameters in the appendix one. Here are some functions used in embroidery. 1. Cyclic Embroidery This function can increase the embroidery productivity. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 66: Set User-Defined Parameter

    Chapter 5 Management of Machine Parameters When the parameter“To Do Cyclic Emb.”is set as “Yes”, the cyclic embroidery function is enabled and the icon will appear in the main screen. When this function is enabled, after completing the designated design, the machine will automatically embroider it again without pulling the bar.
  • Page 67 You may press “ ” to cancel. 、 3. Press to go to the next page. Repeat the step 2. Then press to shift between the pages. The user-defined parameters are labeled with BECS-D56 computerized embroidery machine owner’s manual...

  • Page 68: Purview Of Machine Parameter Manage

    Chapter 5 Management of Machine Parameters 4. Press the key “ ”to save and system goes back to machine parameter screen. 5. Move the cursor to “set user-defined parameter”, press the key “ ”to enter user-defined parameter screen. The setting is similar to other parameter setting. Note: when you enter the screen of user-defined parameter, system will automatically clear the saved ones.

  • Page 69: Unlock/Change The Administrator Password

    The administrator has to input the right password before modification. 1. Press “ ”in the main screen to enter machine parameter management, move the cursor to unlock/change the administrator password, press “ ” to enter the authorization management screen. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 70: Machine Administrator Cancels Machine Lock

    Chapter 5 Management of Machine Parameters 2. Move the cursor to “Unlock/Change the admin password”, press “ ”and input the old password then input a new one. The administrator needs to input the old password and new password one by one. The machine producer will tell the administrator about default password which is in 4-9 digits.

  • Page 71: Administrator Reset (Or Save) The Optimized Parameter

    3）Turn up " Save the admin’s machine parameter", and then press “ ”key. After finishing the operations at above, the parameters are saved successfully. If user needs reset the optimized parameters, please follow the steps at below: BECS-D56 computerized embroidery machine owner’s manual...

  • Page 72: Change The Factory Password

    Chapter 5 Management of Machine Parameters 2、 Administrator reset optimize parameter 1）At main interface , press " "key to enter the machine parameter management screen. Move cursor to “Purview of Machine Parameter Manage” and press to enter the Purview of Machine Parameter Manage screen 2）Press move the cursor to "...

  • Page 73: Unlock The Factory Password

    6. When that factory password has not been set and administrator password has been set and locked, all administrator-authorized machine application parameters are recovered to administrator saved values and other parameters are initialized to the default values. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 74: Save All Parameter To Disk

    Chapter 5 Management of Machine Parameters 5-6 Save all parameter to disk 1. Press " " in main screen to enter the Machine Parameter Operation screen. Then move cursor to " Save All Parameters To Disk ", and press “ ”key.

  • Page 75: Read All Parameter From Disk

    " in main screen to enter the Machine Parameter Operation screen. Move cursor to "Read All Parameters From Disk ", and press “ ”key. 2. The system will display "Ready Parameters –Saved Disk To Read All Parameters ", and user needs press “ ”key. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 76: Adjust Parameters Of X＆Y Servo Drivers

    Chapter 5 Management of Machine Parameters 3. "Success to read all parameters" will appear in screen. After the above operations, the system parameters will resume to the status before user updates the software. The embroidery machine can be used now. 5-8 Adjust Parameters of X＆Y Servo Drivers These parameters are used for the Dahao all-servo high-speed machine, whose main shaft uses Dahao servo motor and driver.

  • Page 77: Set The Parameter

    And the parameters can be saved even power is off. 5.8.4 Restore default driver parameters The X＆Y parameters of servo driver in the machine will be restored to their default values if you operate this item. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 78: Chapter 6 Assistant Operation

    Chapter 6 Assistant Operation Chapter 6 Assistant Operation 6-1 Assistant embroidery operation Press the other function key “ ” in the main screen to enter the management screen of the machine parameters. Then move cursor to “assistant emb operation” to enter that screen. If the frame origin has been set (see 6.2.3), in the status of embroidery confirmation, you can perform design start point operation.

  • Page 79: Save Design Start

    (see 6.2.5) so that you can embroider the design to the center of the frame. 1. Follow the above instruction and enter assistant embroidery operation screen. 2. Move the cursor to “Auto to start position” and press “ ”. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 80: Stitch Stop Down

    Chapter 6 Assistant Operation Press “ ”to confirm, then the system will find the centre of frame and move to that position; press “ ”to cancel the operation. 3. System goes back to the main screen. 6.1.4 Stitch stop down This function is used for the embroidery of the entire fabric.

  • Page 81: Setting Another Start

    X and Y. User needs press the frame-moving key to move the frame to the offset point and press “ ”to confirm it, or press “ ”to cancel the operation. 4. The system will save the position of the offset point and return to the main screen. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 82: Set B Point

    Chapter 6 Assistant Operation 6.1.6 Set B Point This function is optional and the user has to book it advance. This function is developed to solve the problem of threading when thread-breakage appears on giant machine. When thread breaks, user needs press the slow switch to let the machine trim. Then the frame will move to the point B.

  • Page 83: Operation On Afc, Sequin And Coiling Devices

    ” in the main screen to enter the “Machine Parameter Manage” screen, Then move cursor to “Other assistant operation” and press “ ”to enter the interface, where user can activate the relating functions by pressing the corresponding button. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 84: View Embroidery Parameter

    Chapter 6 Assistant Operation The screen is similar to that for assistant embroidery function. The words on the keys can help to explain their functions. 6.2.1 View Embroidery Parameter The user can check the current design’s parameter and some machine conditions. 1.

  • Page 85: View Statistics Information

    ” to enter the “Machine Parameter Manage” screen. Then move cursor to “Other assistant operation” and press“ ” to enter that screen.. 2. Move the cursor to “Power resume setting/ frame start setting” and press“ ”. 3. Use to choose between “Manual” and “Auto”. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 86: Power Resume

    Chapter 6 Assistant Operation 4. Press “ ” to confirm it or press “ ” to quit. Before setting the frame start manually, user needs move the frame to the desired origin position and press “Manual”. Then the system will save the current frame position as the frame origin.

  • Page 87: Set Embroidery Scope In Software

    ”to set the coordinate of top-right corner. Use frame-moving key to move the embroidery frame. After you confirm the top-right corner, press “ ”to confirm. 5. Move frame and input the coordinate of bottom-left corner. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 88: Set System Clock

    Chapter 6 Assistant Operation Use the frame-moving key to confirm the bottom-left corner, press “ ”to confirm. 6. System will record frame software protection. 6.2.6 Set system clock In date and time screen, users can check and modify the current date and time. 1.

  • Page 89: Language Choice

    1. Press “ ” to enter the “Machine Parameter Manage” screen. Then move cursor to “Other assistant operation” and press“ ” to enter that screen 2. Move the cursor to “machine soft information” and press“ ”. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 90: Help

    Chapter 6 Assistant Operation This function is used for checking the software of upper and lower machine, press “ ”to exit. 6.2.9 Help 1. Press “ ” to enter the “Machine Parameter Manage” screen. Then move cursor to “Other assistant operation” and press“ ”...
  • Page 91 Test hook solenoids/ motor Splay Scissor’s Angle Trim Motor to Find Origin Test thread breakage detection Thread Breakage Statistics Count of Roller Thread Breakage Device Test Upper Thread Hold Function Test Simple Taping Thread-loosing Motor BECS-D56 computerized embroidery machine owner’s manual...

  • Page 92: Chapter 7 Other Operation

    Chapter 7 Other Operation Chapter 7 Other Operation 7-1 Operation on color-changing order The design’s color-changing order is saved with the design. Press the key in the main screen . You can operate color-changing order in the following screen. 7.1.1 Input Color Line 1.

  • Page 93: Modify Color Line

    “ ”to exit without saving. 7.1.3 Replace a needle 1. In Color Line Operation screen, move the cursor to “replace a needle” and press “ ” to enter that screen: BECS-D56 computerized embroidery machine owner’s manual...

  • Page 94: Set Color Of Showing Design

    Chapter 7 Other Operation 2. Press the digital key to input “replacing from needle” and press “ ”to confirm and type in digits in “replacing to needle”, then press “ ”to save or press the key “ ”to exit without saving. 7.1.4 Set color of showing design In order to make the showing effect close to the real embroidery design, the system supports setting of each needle bar color.

  • Page 95: Design Border Operation

    The function is used for checking current design boundary information and displaying it. 1. Move the cursor to “check the boundary of a design” and press “ ”. System will display the peripheral information of the design in the window: BECS-D56 computerized embroidery machine owner’s manual...

  • Page 96: Move The Frame Along The Boundary Of A Design

    Chapter 7 Other Operation 2. Press “ ”or “ ”to close the window. 7.2.2 Move the frame along the boundary of a design The function can drive the frame moving along the border. If it touches the limit, system will correct it to avoid over-limit in real embroidery. 1.

  • Page 97: Create Design From Outline

    1. In preparation status, you can move the cursor to “Frame to generate design, then embroider back” and press “ ” to enter the Frame and Make Design screen: BECS-D56 computerized embroidery machine owner’s manual...

  • Page 98: Embroider A "+" In Current Position

    Chapter 7 Other Operation 2. Press the key to shift stitch (flat or jump). Press the manual frame moving key to let the frame go along the border. Press at each turning point. 3. After edition, you need press and“ ”, then system will ask for new design number and name.

  • Page 99: Frame And Embroider Back For One Line

    ”. The system will display the start point of the frame-moving 2. Move the frame to the start point of the line, press “ ”to confirm the first point. System will ask to move frame to the end point. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 100: Embroider The Boundary Of Current Design

    Chapter 7 Other Operation Move to the end point and press the “ ”to confirm the second point. 3. System will generate temporary data of the line and return to the main screen. Now system displays on the main screen. Pull bar to embroider line, after that, system returns to the embroidery preparing status.

  • Page 101: Embroider True Boundary Of Current Design

    ” in the main screen to enter the “Machine Parameter Manage” screen. Then move cursor to “positioning idling” and press to enter that screen, where the system provides a list of function keys. You can press these keys to perform different idling functions. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 102: Go Ahead Stitches

    Chapter 7 Other Operation 7.3.1 Go ahead stitches 1. In the screen of positioning idling, move the cursor to “go ahead stitch” and press“ ”. 2. Input the stitch number of “go ahead stitch”. System goes to the screen of “go ahead stitch”. You can press “ ”to confirm or press “...

  • Page 103: Next Color Code

    ”on the keyboard, then the system will ask for user’s confirmation. You may press “ ”to set X and Y values as 0. Press the key “ ”to cancel. The user can check the values in the main screen. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 104: Chapter 8 Memory Design Edition

    Chapter 8 Memory Design Edition Chapter 8 Memory Design Edition You can edit common designs in the memory through this function, or establish a new design. 8-1 Start Editing Design Press in the main screen to enter the memory design management screen. Select the design and then press “...

  • Page 105: Document And View Operation

    1. positioning stitch to the design start point to the design end point to last color-changing code to next color-changing code to last jump code to next jump code BECS-D56 computerized embroidery machine owner’s manual...
  • Page 106 Chapter 8 Memory Design Edition Press to position the high speed current stitch, press to locate low speed current stitch position, press to shift among 1&10,100&1000, lockstitch, stop, color-changing, jump and sequin. 2. editing stitch Click to add one designated stitch type at present position. Press to change stitch type.

  • Page 107: Chapter 9 Letter Design

    ” to adjust it. After adjustment, user can press “ ”again to save it. The following picture is the letter string input screen. 1. “Char string”: means the letter list that will be embroidered BECS-D56 computerized embroidery machine owner’s manual...
  • Page 108 Chapter 9 Letter Design 2. “Font style”: means the letterform that is used for embroidering letter. The letterform selected here will be applied on all of the letters if necessary. (for the font adjustment of the single letter, please refer to the section of “create character pattern”). This is the font style window: You can press “...
  • Page 109 “Center”: Zoom to see the diagram, show the whole pattern. “window shift": Click this key, screen will turn dark. Press move the window. Letter design moves along with the window. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 110 Chapter 9 Letter Design “Save”: it is used for saving letter pattern that is being edited. After user clicks that key, the system will display the window that user can input the pattern number and pattern name. According to the pattern name and pattern number that need modification (the serial number does not need modification generally), user can click “...
  • Page 111 “Density increase”: Increase stain stitch density of the letter pattern. Such as: “Density reduces”: Reduce stain stitch density of the letter pattern. Such as: “Level overturns”:turn over the selected letter horizontally. “Flip vertical”: Turn over the selected letter vertically. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 112: Character Pattern Save

    Chapter 9 Letter Design “Change color switch”: Select the button or cancel the change of color that was before the selected letter. “Change font”: change letterform of selected letter. After user clicks this key, system will give the dialog box of selecting letterform. User needs choose one of letterforms that is wished, and confirm it.

  • Page 113: Chapter 10 Jf Type Sequin Embroidery

    Design with Sequin codes has its own format. JF type multi-sequin embroidery of BECS-D56 machine is divided into two types: one is normal multi-sequin design, made by normal design making method. The other one is special multi-sequin design made by normal design software with special making method.

  • Page 114: Embroider Sequin

    Chapter 10 JF type sequin embroidery C. Specifications 1. Sequin diameter range: 3mm,4mm,5mm,6.75mm and 9mm; 2. The maximum speed for sequin embroidery is 850 rpm. D. A/B/C/D means four sequin-feeding equipments. If four sequins are delivered in the same time, A will be on the top, then B, C and D. 10-2 Embroider sequin You may follow the steps in sequin embroidery: 1.

  • Page 115: Sequin Design Edition

    ” in the main screen to enter the design manage window, as shown at below: 2. Press direction keys to select sequin design for edition. Use key to turn page and select key to enter the sequin edition screen: BECS-D56 computerized embroidery machine owner’s manual...
  • Page 116 Chapter 10 JF type sequin embroidery 3. Press the key to enter the Way of Select Sequin window: 1） Move the cursor to this menu and press “ ”to select one sequin: This helps users to directly select a sequin to edit with direction keys. 2）...
  • Page 117 There are altogether 15 sequin modes for users to choose: A、B、AB、C、AC、 BC、ABC、D、AD、BD、ABD、CD、ACD、BCD、ABCD. Sequin name are A, B, C and D. If all four sequins are sent at same time, sequin A will be on the top, then B, C and D. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 118 Chapter 10 JF type sequin embroidery 6. Edition of Alternative Sequin You should first select a group of sequins or sequins with the same color, then press to edit. Method: 1） Use to select sequin mode and press “ ”to confirm. Sequin names are A, B, C and D.

  • Page 119: Parameter About Multi-Sequin Embroidery

    In this section, we will introduce how to debug the sequin device and set the relating parameters for multi-sequin. " " Press the key in the main screen to enter the Machine Parameter Manage screen and select “sequin parameter” to enter the Sequin Parameter screen: BECS-D56 computerized embroidery machine owner’s manual...
  • Page 120 Chapter 10 JF type sequin embroidery (1) Speed for Sequin R(L): This parameter is the Max speed of sequin embroidery Note: the maximum speed of flat embroidery should be higher or equal to speed limits for sequin embroidery. Move the cursor to this parameter and press“ ”to enter it.
  • Page 121 This parameter is for the beam embroidery device. “0” means to turn off the sensitivity of the beam-breakage detection. The range of this parameter is 0~10. “1” means the highest sensitivity, while “10” means the lowest sensitivity. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 122 Chapter 10 JF type sequin embroidery (13) Motor Number of R (L) Sequin This parameter should be set according to mechanism. If there is no sequin device, you should set it as “0”. Move the cursor to this parameter and press“ ”to enter.

  • Page 123: Change Color Order And Set Sequin Mode

    If it is single sequin device or special multi-sequin design, it will not be necessary to set it. For an example of the first needle position 1,when you input 1, the system will show: BECS-D56 computerized embroidery machine owner’s manual...
  • Page 124 Chapter 10 JF type sequin embroidery Setting of sequin-feeding mode: a) Press digital key confirm embroidery needle position, it will show “input sequin mode” at the position that has sequin device. b) Use to modify the delivery mode and press “ ”to confirm.
  • Page 125 ”to end setting. （4） ① press 9，it will show sequin delivery mode screen； ② Use till you see “A” in “input sequin mode”, then press “ ”to confirm； ③ press 9，then press “ ”to confirm； BECS-D56 computerized embroidery machine owner’s manual...

  • Page 126: Manual Operation Of Sequin Embroidery

    Chapter 10 JF type sequin embroidery ④ Use till you see “B” in “input sequin mode”, then press “ ”to confirm； ⑤ press 8，then press “ ”to confirm； ⑥ You should use till you see “C” in “input sequin mode”, then press “...

  • Page 127: Debugging Multi-Sequin Embroidery

    (3) Manual operation of rear motor for feeding C sequin Press the sequin switch to the down side, turn thread-breakage detection switch to the down side too (the head light is off at this moment) and press manual sequin-feeding button. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 128: Sequin Mending

    Chapter 10 JF type sequin embroidery 2. Collective debugging Press the key “ ” in the main screen to enter the “Machine Parameter Manage” screen. Move cursor to “Assistant Emb Operation” and then select “Machine Test” press “ ”to enter the window. As shown in below, pressing &...

  • Page 129: Chapter 11 Directions On Coiling, Taping And Zigzag Embroidery

    2. Speed of special Embroidery: 300—600rpm, adjusting step at 10r/m. 3. Manual rotating angle of M-axis: 18°/step. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 130: Parameters And Setting

    Directions on Coiling, Taping and Zigzag Embroidery Chapter 11 11-3 Parameters and setting Press the “ ” in the main screen to enter the parameter setting screen. Then move cursor 、 to “Special Embroidery Parameter” and click “ ” to enter that screen. Pressing is to shift page.
  • Page 131 “0” when needle falls in the center of tape. If not, please repeat the adjustment to realize the best effect. Generally, this parameter should be managed by professional experts before leaving factory. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 132: Relative Operations Of Special Embroidery

    Directions on Coiling, Taping and Zigzag Embroidery Chapter 11 7. D44 M Axis Work OFF Angle: 0, 90 In normal and sequin embroidery, if this parameter is set at 0, the M axis will stop at the horizontal position; if it is set at 90, the M axis will stop at the vertical position. When the distance between the normal embroidery head and special embroidery head is small, this parameter must be set as 90°...
  • Page 133 Input “1” (special head) to change special embroidery mode: Press relative icon to select the embroidery mode you need. Press “ ” to save the changes, or press “ ”to exit. After user saves the changes, system will display as: BECS-D56 computerized embroidery machine owner’s manual...

  • Page 134: M Axis Operation Of Special Embroidery

    Directions on Coiling, Taping and Zigzag Embroidery Chapter 11 Note: Icon“MANUAL”is used to activate the manual color-changing at the auto-shift status. The figure “Manual” means that system goes into manual color-changing status. During the embroidery, when the special head finishes the work, the machine will stop at the end point.

  • Page 135: Operations Of Clamp Foot

    Move cursor to “Sway Zig Rod to 100” and click the key “ ”. According to the hint in dialogue window, user can pull bar to let all the swing rods act once. Click “ ”to exit. Users can adjust swing range by using this function. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 136: Steps On Special Embroidery

    Directions on Coiling, Taping and Zigzag Embroidery Chapter 11 2. Clamp Foot Up/ down Move cursor to “Test lift clamp foot” and click the key “ ”, according to the hint in dialogue window, user can pull bar to let all the clamp feet go up/down. Pull the bar again to let them down/up again.
  • Page 137 No proximity switch is taken for positioning. As default setting, the controller sets the foot at the bottom position when user turns on the machine. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 138 Directions on Coiling, Taping and Zigzag Embroidery Chapter 11 (3) Transmitted by 2-phase stepping motor separately, with the holding force and without proximity switch It uses a small 2-phase stepping motor for lifting presser at every special embroidery head and controlling its working height and limited height. At power-off, there is the holding force when the clamp foot stays at the upper point, but not at the bottom point.

  • Page 139: Chapter 12 Instruction On Operating High-Efficiency System

    ” in the main interface to enter “Machine Parameter Manage” screen, then move icon to “Main Shaft Parameter” and input passwords (Dahao general password or special passwords customized by manufacturer) and set the Max Speed to 850 or other values. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 140 Chapter 12 Instruction on Operating High-Efficiency System 3. Press “ ” to quit the interface, turn to “High-efficiency Machine Parameters” and input passwords (Dahao general password or special passwords customized by manufacturer). BECS- D56 computerized embroidery machine owner’s manual...
  • Page 141 At this moment, the parameters at the speed setting interface, such as “Max Speed”, “Min Speed” and “Shift Stitch Length” will be unchangeable. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 142 Chapter 12 Instruction on Operating High-Efficiency System 5. If client has higher standards on the embroidery quality, this software will also provide the non-high-efficiency mode. Clients only need set the “High-efficiency Mode” at “No”, the parameters at the speed setting interface, such as “Max Speed”, “Min Speed”...

  • Page 143: Chapter 13 Updating Control Program

    13-1 Update Data Software (Upper Machine) 1. Hold the button “ ”, at the same time turn on the power: 2. The screen shows the following picture, select the first “updating data program” and press enter key: BECS-D56 computerized embroidery machine owner’s manual...
  • Page 144 Chapter 13 Updating Control Program 3. Select the “updating from USB” and press enter key: 4. Select the inserted USB disk, then press enter key: BECS- D56 computerized embroidery machine owner’s manual...
  • Page 145 Chapter 13 Updating Control Program 5. Select the Update Software, such as:D56-D001A1: 6. Press enter key to confirm the updating : BECS-D56 computerized embroidery machine owner’s manual...

  • Page 146: Updating Control Program (Down Machine)

    Chapter 13 Updating Control Program 7. The screen will show “restart” when update is finished. Please turn off power: 13-2 Updating Control Program (Down Machine) “ ” 1. Please hold , at the same time turn on the power: BECS- D56 computerized embroidery machine owner’s manual...
  • Page 147 Chapter 13 Updating Control Program 2. The screen shows the following picture, select the second “updating control program” and press enter key: 3. Select the “updating from USB” , then press enter key: BECS-D56 computerized embroidery machine owner’s manual...
  • Page 148 Chapter 13 Updating Control Program 4. Select the inserted USB disk , then press enter key: 5. Select a control software file in the series of DX6: BECS- D56 computerized embroidery machine owner’s manual...
  • Page 149 Chapter 13 Updating Control Program 6. Press enter key to confirm the updating: 7. The screen will shows “restart” when updating is finished, please turn off power and restart: BECS-D56 computerized embroidery machine owner’s manual...

  • Page 150: Chapter 14 Updating Peripheral Equipment Program

    Chapter 14 Updating Peripheral Equipment Program Chapter 14 Updating Peripheral Equipment Program Updating Procedure: 1. In main screen, press “ ” key to enter “Machine Parameter Manage” screen and then move the cursor to “Assistant Emb Operation” , and press “...
  • Page 151 Chapter 14 Updating Peripheral Equipment Program 4. Move the cursor to " Update Head Board Software ", and press " " key. 5. At main interface , press " " to select USB. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 152 Chapter 14 Updating Peripheral Equipment Program 6. Press " " select the software for update , and press " " key. 7. The system will display “Update Software of Peripheral board"，and press " " key. 8. Wait for updating software. And the screen will display "Success" when updating is finished.

  • Page 153: Appendix Ⅰ Parameter Setting List

    If “No”, the empty stitches won’t be omitted. Whether start color-changing way when Start No, Yes the later needle position is Same Colors same to the former one in color-changing order. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 154 Appendix Ⅰ Parameter Setting List Recommended Number Name Range of Setting Note Value “Yes”, manual color changing will be stored in Store Manual the color-changing order. No, Yes Color After embroidery, setting will automatically change to “No”. Slow STI. 0~500 After Patch Speed After...
  • Page 155 Action Angle Frame Parameter high-speed servo Frame Curve F1~F6 machine doesn’t have this parameter. Frame Angle 230~290 Frame-moving F1～F6 Curve Y Over frame by No, Yes Step High Frame-Shift 1~30 Speed Frame-Shift 1~30 Speed BECS-D56 computerized embroidery machine owner’s manual...
  • Page 156 Appendix Ⅰ Parameter Setting List Recommended Number Name Range of Setting Note Value Speed When 0,1,2…30 Over frame (AFC) Use No, Yes (AFC) Interval 0~15 Time It is fit for high-speed direction 230~280 machine using Dahao Frame Angle A servo-motor driver. direction 230~280 The same as above.
  • Page 157 Thread-trimming Parameter Turn No, Yes Trimming Jump & Trim 3 Stitch No Trim, 1 Sti.~7 Sti. 1 is the min trimming length Length and 8 is the max trimming Trim length. Speed When 80,90,100…250 Trimming BECS-D56 computerized embroidery machine owner’s manual...
  • Page 158 Appendix Ⅰ Parameter Setting List Recommended Number Name Range of Setting Note Value Lock Stitch. No, Yes When Trim Lock Stitch Trim Lock Stitch 0.3~2.0 Len Bef Trim 1 is the min trimming length Length and 8 is the max trimming Trim length.
  • Page 159 Range: 0~15. For the machine using valve to control presser, this parameter needs setting at Time of Sequin 0~15 2~3; for the machine with Action stepping motor control presser, this parameter needs setting at 4~5. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 160 Appendix Ⅰ Parameter Setting List Recommended Number Name Range of Setting Note Value It is used to control the position Sequin No, Yes of the sequin device after the after T.B. thread-breakage. Sequin Ind. No, Yes UpDown Valve When Jump & No, Yes Nocut R Motor Shift...
  • Page 161 Dual-way 6~40 steps Set 5MM of L Single-way 6~40 steps; Sequin Dual-way 6~40 steps Set 6.75MM of Single-way 6~40 steps; L Sequin Dual-way 6~40 steps Set 9MM of L Single-way 6~40 steps; Sequin Dual-way 6~40 steps BECS-D56 computerized embroidery machine owner’s manual...
  • Page 162 Appendix Ⅰ Parameter Setting List Recommended Number Name Range of Setting Note Value 3/4/5/6.75/9mm A Size&Color 5mm yellow Yellow/Purple/Blue/Green/ of L Sequin Red/ Golden/ Silver/Cyan 3/4/5/6.75/9mm B Size&Color 5mm blue Yellow/Purple/Blue/Green/ of L Sequin Red/ Golden/ Silver/Cyan 3/4/5/6.75/9mm C Size&Color Update the new parameter 5mm silver Yellow/Purple/Blue/Green/...
  • Page 163 Z Emb Swing Rotary 0~10 of M Axis M Axis Work 0,90 OFF Angle Spec. Emb. No Trim Low, Above & Low, No Trim Trim Mode Speed 300~700 Sequin L Spec Minimum 250~400 Speed BECS-D56 computerized embroidery machine owner’s manual...
  • Page 164 Appendix Ⅰ Parameter Setting List Recommended Number Name Range of Setting Note Value Spec. Speed-Down 1~180 Angle Spec. Speed-Down Ratio Shaft Control 0~180 Angle Zigzag 1,2,3 Rod Angle Ratio of Coil 1 Sti/L 1~4 Sti/L Emb. Slow Down When Coil No, Yes High-speed System Parameters Only when this parameter is...
  • Page 165 It is used for setting the subnet mask of machine IP Subnet mask address when it connects to It is used for setting the Gateway gateway of machine when machine connects to PC. 0~1.0 Quilt 0~1.0 Quilt BECS-D56 computerized embroidery machine owner’s manual...
  • Page 166 Appendix Ⅰ Parameter Setting List Recommended Number Name Range of Setting Note Value Time for one lubricating 10sec 1～10 (sec) Stitches 10,000,000 between 1～10 million stitches stitches lubrications compensation -0.5~+0.5 for mechanical compensation -0.5~+0.5 mechanical Machine Head 1~80 Head Interval 162.0 -400.0~-1.0，+1.0~+400.0 Head...
  • Page 167 10~50 Parameter 7 10~50 Parameter 8 10~50 Parameter 9 10~50 Parameter 10 10~50 Parameter 11 10~50 Gear Blacklash 0~50 compensation 0~100 1~255 X/Y Parameter for Servo Frame Adjustment (Y Parameter, Same as X Parameter) BECS-D56 computerized embroidery machine owner’s manual...

  • Page 168: Appendix Ⅱ Directions On Usb Operations

    Appendix Ⅱ Directions on USB operations Ⅱ Appendix Directions on USB operations Operation Direction Remark Read & Write USB Same as floppy disk Priority Supporting format FAT16 and FAT32 Long filename Support but no display For instance： “清明 DOS 8.3 mode （8 digit prefix is 上河图.DST”will Filename display be displayed as “清...

  • Page 169: Appendix Ⅲ Error Information & Instruction Of System Level Mistake

    Design not existed! Open design error! Error type combined design Open FLASH media error Design has created! No enough design mem. Directory is invalid. FLASH media write-protect Design file not existed Design name is invalid BECS-D56 computerized embroidery machine owner’s manual...
  • Page 170 Appendix Ⅲ Error Information Mistakes Design file corrupt Error read/write design Not open design file Error read FLASH media Device not existed! No floppy disk Invalid disk type Disk sector error File not in disk Not a file File corrupt disk write protect Invalid directory File existed!
  • Page 171 CHANGE CLR OVERLIMIT EC22 MAIN MOTOR REVERSE EC23 CANNOT EMBROIDER EC24 CANNOT FRAME BACK EC26 CAN NOT TRIM EC36 SEQUIN IS ON EC37 PULL BAR ERROR EC38 SPE. EMB. OVERTIME EC41 FILE NOT EXIST BECS-D56 computerized embroidery machine owner’s manual...
  • Page 172 Appendix Ⅲ Error Information Mistakes EC42 FILE DIRECTORY FULL EC43 MEMORY SPACE FULL EC44 FILE FAT ERR EC45 FILE DIRECTORY ERR EC46 HAS BAD SECTORS EC95 Thread is broken, press key EC101 Transfer CRC Error Instruction of System Level Mistake on CX8/CX9 Model： At present, the CX8/CX9 model may give 2 system-level warning at start-up: the one is “Data Abort”;...

  • Page 173: Appendix Ⅳ Make Special Multi-Sequin Design

    The value of sequin A+C+D is 13，we use 1 sequin code plus 12 jump stitches. The value of sequin B+C+D is 14，we use 1 sequin code plus 13 jump stitches. The value of sequin A+B+C+D is 15，we use 1 sequin code plus 14 jump stitches. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 174 Appendix Ⅳ Make Special Multi-Sequin Design 2、 Make Motif for multi-sequin By using the function of making Motif, we can easily input sequin or sequin combinations. Example: A, B, A+B, C, A+C, B+C, A+B+C, D, A+D, B+D, A+B+D, C+D, A+C+D, B+C+D, A+B+C+D, etc. We here take sequin B designing as an example.
  • Page 175 Appendix Ⅳ Make Special Multi-Sequin Design 3) Since the value of sequin B is 2, we should put 2 sequins in here, which means, we have to add another sequin. 4) Continue to type in other single-stitches. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 176 Appendix Ⅳ Make Special Multi-Sequin Design 5) You can see “stitch list” shows 2 sequins as the following image. 6) Select all stitches. 7) Making Motif, group is JP, name is JP-B 8) Input two reference points. BECS- D56 computerized embroidery machine owner’s manual...
  • Page 177 Appendix Ⅳ Make Special Multi-Sequin Design Single needle multi-sequin, you can use “Stitch form -> Motif -> 3、 Apply”. Then “manual stitch” to finish entering. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 178 Appendix Ⅳ Make Special Multi-Sequin Design 4、 Others (curve) can apply trace too, also the motif. 1) Click sequin button to enter “sequin status” (this is to ensure all the curve section have sequin, it is of importance.). Input the curve as the following.
  • Page 179 Appendix Ⅳ Make Special Multi-Sequin Design 2) Select a target. 3) Set “target properties” and select related trace. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 180 Appendix Ⅳ Make Special Multi-Sequin Design 4) “Multi-sequin” input is finished. 5、 Make alternative sequin design This is to realize the embroidery of different sequin alternatively. For instance, alternative A1B1 embroidery can realize embroidery effect of A, B, A, B… BECS- D56 computerized embroidery machine owner’s manual...
  • Page 181 4 sequin delivery devices at most. So we can get the following 15 combinations: A,B,AB,C,AC,BC,ABC,D,AD,BD, ABD,CD,ACD,BCD,ABCD. The design data base should be the combination of the above sequin sizes and sequin groups. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 182 Appendix Ⅳ Make Special Multi-Sequin Design If there are two sequin delivery devices A and B, and A design document uses 3MM sequin and 5MM, the design data base should contain 3MM-A base, 5MM-B base, and 5MM-AB base. While the other design uses 4MM and 6.75MM, then the design data base should contain 4MM-A, 6.75MM-B and 6.75MM-AB.
  • Page 183 Appendix Ⅳ Make Special Multi-Sequin Design You can see the stitch list as the following image. The first sequin is overlap A+B, the second one is sequin A. Save as the TAJIMA DST document. BECS-D56 computerized embroidery machine owner’s manual...

  • Page 184: Appendix Ⅴ Network Connection Of Embroidery Machines

    Appendix Ⅴ Network Connection of Embroidery Machines Ⅴ Appendix Network Connection of Embroidery Machines I、 Making Ethernet cable 1、 Making straight-through cable The pins in the two terminals of twisted-pair cable have to be in one-to-one correspondence. If the first pin of one terminal is green, the first pin of the other terminal must be green as well.
  • Page 185 Every computer in the internet relies on the IP address to mark itself. It’s like we find the phone by the phone number in the phone book. In one network the IP address must be BECS-D56 computerized embroidery machine owner’s manual...
  • Page 186 Appendix Ⅴ Network Connection of Embroidery Machines unique. 2) Form of IP address One IP address includes 4 decimal integers partitioned by decimal points. Each integer is in fact composed of 8 binary numbers. So the maximum of each integer is 255 and the minimum is 0.
  • Page 187 III、 The ways to construct network 1、 One PC directly connected to one embroidery machine In this situation, crossover cable is used to link the network interface of PC to the network interface of embroidery machine. BECS-D56 computerized embroidery machine owner’s manual...
  • Page 188 Appendix Ⅴ Network Connection of Embroidery Machines 2、 PC and embroidery machine linked by HUB In this situation straight-through cable is used to link PC with HUB. 3、 Connect the two networks in “2 ”through HUB IV、 Setting the network parameters of embroidery machine 1、...

Table of Contents

Save PDF