Table of Contents
Advertisement
Quick Links
USER'S GUIDE
Important! Read First ......................................
Fastener Legend...............................................
Front and Back Plates.......................................
Rear Shaft Assembly.........................................
Front Shaft to Keel............................................
Front Height Shaft to Spine...............................
Saw Spine to Keel.............................................
Rear Height Screw to Keel................................
Pitch Adjustor Assembly....................................
Rear Spine Guide.............................................
Pitch Adjustor/ Spine Guide..............................
Front Spine Guide............................................
Saw Blade Guides............................................
Transmission Check.........................................
Travelers...........................................................
Keel Assembly to Frame...................................
Assembly Detail................................................
Dovetail Ways...................................................
Inside Dovetail Sliders......................................
Table Bumpers..................................................
Outside Dovetail Sliders....................................
Fence and Trap Clamps....................................
Saw Blade.........................................................
Blade Alignment................................................
Cursor and Flip Down Stops............................
Blade Height Stop.............................................
Optional Stand..................................................
Stand Corner Key.............................................
Lubrication Guide.............................................
Cutting guide....................................................
Notes ...............................................................
Parts List..........................................................
1101-284-08 Rev. 1
1
4
5
5
6
6
7
7
8
8
9
9
10
10
11
11
12
12
13
13
14
14
15
15
16
16
17
18
19
20
21
22
Made in the USA
www.BridgeCityTools.com
Advertisement
Table of Contents
Related Manuals for Bridge City Jointmaker Pro Signature Series
Summary of Contents for Bridge City Jointmaker Pro Signature Series
-
Page 1: Table Of Contents
Fastener Legend... Front and Back Plates... Rear Shaft Assembly... Front Shaft to Keel... Front Height Shaft to Spine... Saw Spine to Keel... Rear Height Screw to Keel... Pitch Adjustor Assembly... Rear Spine Guide... Pitch Adjustor/ Spine Guide... Front Spine Guide... -
Page 2: Important! Read First
OVERVIEW The Jointmaker Pro is the world’s first stationary hand cross- cut saw and will accurately allow you to make most of the cuts required in wood joinery plus a myriad of other sawing applica- tions. Consisting primarily of two independent linear tables mounted over specially designed, fine-toothed saw blades, the Jointmak- er Pro redefines the meaning of “cut by hand.”... - Page 3 To correctly set the blade for this cut, you would adjust the blade so that the first couple of teeth are below table height, and the last tooth of the saw blade is set with the pitch adjustor to approximately 1/32” above the stock of the wood. With the stock held firmly against the fence, one stroke and the cut is complete, smooth and accurate.
- Page 4 The slider closest to the saw blade on each table is fixed (non-adjustable). The acetyl slider furthest from the saw blade on each table is adjustable and when properly tensioned, both tables will slide smoothly without any lateral slop.
-
Page 5: Fastener Legend
6-32 Nut x 4 3/8-16 Jam Nut x 1 Dovetail Nut 5-40 x 3/16” Philips Head Screw x 5 6-32 x 5/16” Button Head Cap Screw x 4 10-32 x 3/8” Socket Flat Head Screw 4-40 x 1/2” Socket Flat Head Screw x 1 8-32 x 3/8”... -
Page 6: Front And Back Plates
1. FRONT & BACK PLATES 2. REAR SHAFT ASSEMBLY... -
Page 7: Front Shaft To Keel
3. FRONT SHAFT TO KEEL 4. FRONT HEIGHT SHAFT TO SPINE... -
Page 8: Saw Spine To Keel
5. SAW SPINE TO KEEL 6. REAR HEIGHT SCREW TO KEEL... -
Page 9: Pitch Adjustor Assembly
7. PITCH ADJUSTOR ASSEMBLY 8. REAR SPINE GUIDE... -
Page 10: Pitch Adjustor/Spine Guide
9. PITCH ADJUSTOR/SPINE GUIDE 10. FRONT SPINE GUIDE... -
Page 11: Saw Blade Guides
11. SAW BLADE GUIDES 12. TRANSMISSION CHECK... -
Page 12: Travelers
13. TRAVELERS 14. KEEL ASSEMBLY TO FRAME... -
Page 13: Assembly Detail
15. ASSEMBLY DETAIL 16. DOVETAIL WAYS... -
Page 14: Table Bumpers
17. INSIDE DOVETAIL SLIDERS 18. TABLE BUMPERS... -
Page 15: Outside Dovetail Sliders
19. OUTSIDE DOVETAIL SLIDERS www.BridgeCityTools.com 20. FENCE AND TRAP CLAMPS... -
Page 16: Saw Blade
21. SAW BLADE 22. BLADE ALIGNMENT www.BridgeCityTools.com... -
Page 17: Cursor And Flip Down Stops
23. CURSOR AND FLIP DOWN STOPS 24. BLADE HEIGHT STOP www.BridgeCityTools.com... -
Page 18: Optional Stand
25. OPTIONAL STAND... -
Page 19: Stand Corner Key
26. STAND CORNER KEY... -
Page 20: Lubrication Guide
27. LUBRICATION GUIDE NOTES... -
Page 21: Cutting Guide
CUTTING GUIDE NOTES... -
Page 22: Notes
NOTES... -
Page 23: Parts List
Rip Blade blades 1101-201RB6 Rip Blade blades 1101-201RB3 (5 Pack) Cross Cut B 32 TPI blades 1101-201RB2 (5 Pack) Cross Cut B 32 TPI blades 1101-201RB5 Cross Cut A 28 TPI blades 1101-201RB4 Cross Cut A 28 TPI blades 1101-201RB1 (5 Pack) Trap Fence 1101-201-02 Trap Jaws, Left and Right... - Page 24 SATISFACTION GUARANTEE If, for any reason, you are not 100% satisfied with your purchase, simply contact us WITHIN 90 DAYS of receipt for possible remedies, in- cluding return instructions. Should you require a return authorization, please contact us for packaging requirements. DO NOT DISASSEMBLE your Jointmaker Pro.
Need help?
Do you have a question about the Jointmaker Pro Signature Series and is the answer not in the manual?
Questions and answers