Pairing With A Bluetooth; Using Your Headset; Charging The Headset - Logitech mobile freedom Setup & Installation

Pairing with a Bluetooth

Phone
®
You must pair your headset to a Bluetooth
For more details, refer to your mobile phone user guide or contact the phone's manufacturer.
1. Turn on your phone. Make sure the battery is charged in both devices. Turn off the Headset.
2. Press and hold the Multi-function button until the headset indicator
light flashes blue and red (about 10 seconds).
3. The Headset is now in Pairing mode. Release the button. The indicator
light will continue flashing red and blue.
4. Follow the pairing instructions for your Bluetooth
this is done by going to a 'setup' or 'connect' menu and then selecting
the options to 'discover' Bluetooth devices.
®
5. Your phone should find the 'Logitech HS02-Vxx' headset.
Confirm to pair.
6. Your phone should prompt you for a passkey or PIN.
The PIN/passkey is: 0000.
7. If pairing was successful, the Headset LED will flash blue.
8. If pairing fails turn the headset and phone off and repeat the process.
9. Red and blue flashing will return to stand-by mode (blue flashing LED) if not paired in 2 minutes.
Headset Operation Activation
Turning On Press multi-function button for more than 3 seconds
Receiving incoming call None - Automatic
Answering call Briefly press multi-function button
During call
None - Automatic
Mic Mute-on during call Press + volume button more than 2 seconds
Ending mic mute Press + or - volume button briefly
Ending call Press multi-function button briefly
Pairing Option 1 While off, press MFB for about 8 seconds until RED
and BLUE flashes (times out after 2 minutes if no
pairing)
Option 2
From Standby, press MFB for about 8 seconds until
RED and BLUE flashes (times out after 2 minutes if
no pairing) no pairing)
Standby or connected None
In standby mode, press multifunction button, say
Voice Dialing
name (stored in phone) after tone
Low Battery None - Automatic
(<30 minutes)
Turning off Press multi-function button for more than 3 seconds
Connection to power adapter charger and plugging
Charging
3
into electrical outlet
English
Mobile Phone.
®
phone. Typically,
®
LED Status Sounds
5 BLUE flashes brief low-to-high tone
3 repeating BLUE flashes melody increases in volume
3 repeating BLUE flashes single beep when answered
4 repeating BLUE flashes no beep
4 repeating BLUE flashes double-beep every 30 seconds
4 repeating BLUE flashes single beep
3 repeating BLUE flashes single beep
Alternating RED and BLUE flashes single high-low tone beep
Repeating BLUE flash when No beep after pairing
paired
Alternating RED and BLUE flashes single high-low tone beep
Repeating BLUE flash when No beep after pairing
paired paired
1 or 3 repeating BLUE flashes None
4 repeating BLUE flashes single beep
RED flashes last 30 minutes
5 RED flashes high-to-low tone
Continuous ORANGE
(Some funtions are phone dependent)
Comfort & Fit
1. Flip the earpiece and slide the
headset to fit either ear.
2. Rotate the earpiece and slide the
headset over ear to your comfort.
3. Rotate the microphone boom so
it is pointing toward the corner of
Multi-function
your mouth.
button
Please see www.logitech.com for
more information.

Using your Headset

Turning the headset on and off:
Push and hold the multi-function button for 4 seconds. A blue light will flash when on.
Answering/ending a call:
Press the multi-function button.
Muting a call:
Press and hold Volume up for
Volume up or down to discontinue mute.

Charging the Headset

1. Turn off the headset and connect the power adapter.
2. Plug the power adapter to an electrical outlet.
3. The LED will be orange when charging. If the LED is not
orange, the connection is not sufficient.
4. When the LED turns off, your headset is fully charged.
Charging can take up to
1
3 seconds. A repeating beep will indicate that the microphone is muted. Quick-Press of
3 hours.
2 3
4
English