Summary of Contents for Mesqool MS-CR1001
- Page 1 MS-CR1001 AM / FM Projection Alarm Clock Radio Speak with our experts 1-800-303-6081 Mon - Sun 6am to 12am PST 6pm to 12pm PST User Manual support@mesqool.com Version 2.9 Website: www.mesqool.com...
-
Page 2: Table Of Contents
Preface Contents Thank you for choosing our CR1001 AM / FM Projection Alarm Clock Chapter 1 LOCATION OF CONTROLS Radio. For your convenience, we have created a simplified users Chapter 2 POWERING ON & TIME SETTING manual, hoping that it will be easy enough for all to understand and Chapter 3 PROJECTION MODE follow. -
Page 3: Chapter 1 Location Of Controls
Chapter 1 LOCATION OF CONTROLS 9. PROJECTION MODE 10. DST Indicator 11. ALARM 1 Buzzer Indicator 12. ALARM 1 Radio Indicator 13. AM/FM Indicator 14. ALARM 2 Buzzer Indicator 15. ALARM 2 Radio Indicator 16. Focus ring 17. Battery door 18. -
Page 4: Chapter 2 Powering On & Time Setting
Chapter 2 POWERING ON & TIME SETTING 5. In RADIO mode. To change the current time, the Radio must be switched off. Press and hold for RADIO button (8) at least 2 seconds to 1. Connect the adapter line to DC jack (18), then plug into a 100~240V return to CLOCK mode. -
Page 5: Chapter 3 Projection Mode
Chapter 3 PROJECTION MODE 4. Adjust focus ring (16) to adjust the focus on projection clock image until clearly show on the ceiling or on the wall. 1. Press Projection mode button (9) to activate projection function. 2. Press once again to flip the projection clock image reversely. 3. -
Page 6: Chapter 4 High-Low Dimmer/Dst Switch
Chapter 4 HIGH-LOW DIMMER/DST SWITCH Chapter 5 ALARM SETTING 1.HIGH-LOW DIMMER DUAL ALARM FUNCTION Press the HIGH-LOW DIMMER/DST Switch (4) repeatedly to switch the This product features convenient dual alarms. Each alarm function can be set independently, with a choice of Wake To Radio or Wake To display brightness from High Medium Low. - Page 7 3. Press the HOUR/TU- button (2) to set the hour. Press the MIN/TU+ 6. To use Alarm 2, just follow steps 2 to 5 with using the AL2/VOL+ button (7) instead of AL1/VOL- button (6). Similarly, the Wake To button (3) to set the minute. Buzzer indicator is Alarm 2 Buzzer indicator (14) and the Wake To Press to set hour Press to set minute Radio indicator is Alarm 2 Radio indicator (15) on the RIGHT of the...
-
Page 8: Chapter 6 Snooze Setting
Chapter 6 SNOOZE SETTING Chapter 7 SLEEP TIMER SETTING Once the alarm starts sounding, the snooze function can be used to The SLEEP timer function allows the radio to play in blocks of 10, 20, pause the alarm temporarily for 9 minutes before it sounds again. 30, 40, 50, 60, 70, 80, or 90 minutes before turning off automatically, so 1. -
Page 9: Chapter 8 Setting The Sleep Timer And Alarm Together
Chapter 8 SETTING THE SLEEP TIMER AND ALARM TOGETHER Chapter 9 AM/FM RADIO OPERATION 1. If you want to set the SLEEP timer function and Alarm function AM operation: together, you must follow the <Chapter 5 ALARM SETTING> to set the 1.Double press the RADIO button (8) to turn on the radio. - Page 10 Auto Scanning: Press and hold either of the 2 tuning buttons, FM Operation: 1.Press the RADIO button (8) once to turn on the radio. The radio HOUR/TU- button (2) or MIN/TU+ button (3) for more than 2 seconds to receives the FM band with the AM/FM indicator (13) turned on and the start auto scan.
-
Page 11: Chapter 10 Resetting Your Favourite Station
Chapter 10 PRESETTING YOUR FAVOURITE STATION Auto Scanning: Press and hold either of the 2 tuning buttons, HOUR/TU- button (2) or MIN/TU+ button (3) for more than 2 seconds to Presetting AM Station start auto scan. Scanning will stop automatically when a clear radio You can preset up to 10 AM stations. -
Page 12: Chapter 11 Tuning Into A Preset Station
Chapter 11 TUNING INTO A PRESET STATION Presetting FM Station You can preset up to 10 FM stations. These 10 presets are shown as Tuning into preset AM station preset numbers F01, F02, F03, F04, F05, F06, F07, F08, F09 and F10. 1. -
Page 13: Chapter 12 Usb Charging
Chapter 12 USB CHARGING Chapter 13 ABOUT RECOVERY You will need to use an USB adapter cable with a suitable plug for your When something wrong happens to this product such as display show smartphone / iphone / ipad / mp3 player etc. (not included). unnormal numbers,key dysfunction or no effect.please unplug the DC To recharge your device, ensure that the clock radio is connected to AC adapter and take the 1.5V “AAA”... -
Page 14: Chapter 14 Battery Back-Up
Chapter 14 BATTERY BACK-UP Chapter 15 SPECIFICATIONS&CAUTION (For Temporary Time Storage Only) Power Source : AC/DC Adapter-Auto Voltage 100V~240V, 50/60Hz Connect a 3 volt (1.5V “AAA” size * 2pcs.) battery (not included) to the Radio Frequency: FM 87.5 ~ 108 MHZ terminals inside the battery compartment.
Need help?
Do you have a question about the MS-CR1001 and is the answer not in the manual?
Questions and answers
The bell (not alarm) on the right hand side of my alarm clock (that doesn’t have a radio on it) won’t turn off and the alarm goes off at about 7am everyday. There is no way of telling how to shut it off.
To turn off the bell (buzzer) on the Mesqool MS-CR1001 alarm clock:
1. Press the "RADIO" button once.
2. Then press the AL1/VOL- button or the AL1/VOL+ button until the buzzer or radio indicator disappears from the display.
This disables the alarm completely.
This answer is automatically generated
How do I turn off the alarm? I somehow, accidentally set the alarm… Now when it goes off, I can only snooze it, I don't know how to shut it off!
To turn off the alarm on the Mesqool MS-CR1001, you have three options:
1. Press the RADIO button (8) once – This will stop the alarm, but the alarm function remains activated and will sound again after 24 hours.
2. Press the SLEEP/SNOOZE button (5) – This temporarily turns off the alarm for 9 minutes.
3. Do nothing – If no button is pressed, the alarm will continue sounding and automatically turn off after 1 hour.
This answer is automatically generated
How do I set the time?
To set the time on the Mesqool MS-CR1001:
1. Press and hold the TIME SET/PROGRAM button until the display flashes “12:00.”
2. Press the HOUR/TU- button to set the hour.
3. Press the MIN/TU+ button to set the minute.
4. Either press the TIME SET/PROGRAM button once or wait 5 seconds for the display to stop flashing. The clock will then start running from the set time.
This answer is automatically generated
Parts of the numbers are not lighting up, I can’t tell if it’s a 4 or 5 or 8 ( these numbers are examples of the problem)