Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Industrial Scientific iTX1709-5753
Summary of Contents for Industrial Scientific iTX1709-5753
- Page 1 Multi-Gas Monitor P/N 1709-5753 Rev 9 Printed September 2011 Specifications Subject to Change G U A R A N T E E D . F O R L I F E . 1001 Oakdale Road, Oakdale, PA 15071-1500 (412) 788-4353 • Toll Free 1-800-DETECTS FAX 412-788-8353 •...
- Page 2 O U R M I S S I O N Preserving human life on, above and below the earth Delivering highest quality, best customer service … every transaction, every time...
- Page 3 Often times a phone call and a question can save you hours of frustration. Please never hesitate to contact me at 1-800-DETECTS (338-3287). All of us at Industrial Scientific appreciate the opportunity to serve you. Sincerely, Kent D. McElhattan...
-
Page 4: Table Of Contents
ABLE OF ONTENTS ..........3 ARNINGS AND AUTIONARY TATEMENTS ARNINGS AND AUTIONARY TATEMENTS ..............6 NPACKING NSTRUMENT ................7 IEW OF NSTRUMENT ................8 NSTRUMENT PERATION Failure to perform certain procedures or note certain conditions may Turning the iTX On and Off ............8 impair the performance of the instrument. For maximum safety and Gas Reading Mode.................8 iTX O ............9... -
Page 5: Warnings And Cautionary Statements
WARNING (UL CLASSIFICATION, DEMKO CERTIFICATION AND CSA CERTIFICATION ONLY): LE JACK DOIT ÊTRE UTILISÉ SEULEMENT AVEC UNE ALARME EXTERNE INDUSTRIAL SCIENTIFIC N/P 1810-1154 OU UNE ALARME À VIBRATIONS N/P USE ONLY WITH RECHARGEABLE BATTERY PACK P/N 1715-3303, P/N 1708- 1810-2146. -
Page 6: Unpacking The Instrument
After unpacking, if any listed item is missing, contact Visual Alarm Visual Alarm either your local distributor of Industrial Scientific products, or call Industrial Scientific Corporation at 1-800- DETECTS (338-3287) in the United States and Canada, or 412-788-4353. On/Off Mode Key... -
Page 7: Instrument Operation
iTX O NSTRUMENT PERATION IEWING THE PERATING ODES iTX O During Normal Operation, pressing the will scroll URNING THE N AND the instrument through all of the operating modes that To turn the iTX on, press and hold until the have been enabled. -
Page 8: Peak Readings
EADINGS ESETTING ATALOGGING ESSION If the peak hold feature is enabled, press until If the datalogging features are enabled, press until 10.6 “PEAKS” appears. The peak reading displayed represents “Start New Datalog Session” appears. Pressing PEAKS StartNew E to Clear Datalog the highest toxic and explosive gas concentration and the while this screen is displayed will start a new datalogging... -
Page 9: Time/Date/Temperature
EMPERATURE DENTIFICATION Active Site If the time/date/temperature function is enabled, press Press until “Active Site” appears. Monitoring site 14 March 2002 until today’s date appears. The iTX will display the location codes can be entered into the instrument’s None 11:45 AM current time and date along with the current temperature datalogging memory to correspond to measured gas (inside the iTX) in degrees Fahrenheit and Celsius. -
Page 10: Security Code
In General: LARM ONFIGURATION Alarm • Pressing will step you through the modes The “Alarm Configuruation” mode allows you to change Configuration or set a value. alarm set values for each sensor installed. Pressing the • Pressing selects a function or accepts (saves) a will enter you into this menu item. -
Page 11: Quick Calibration
UICK ALIBRATION UMERIC ISPLAY Numeric The “Quick Calibration” mode allows you to turn this The “Numeric Display” mode allows you to choose whether Quick Display Calibration feature on or off. For details on the Quick Calibration your iTX will display actual gas concentrations or relate the feature, please refer to Quick Calibration, page 25. -
Page 12: Non-Latching
Log Data On Alarm Only ATCHING Log Data On Alarm Only Non-Latching The “Log Data On Alarm Only” mode allows you to The “Non-Latching Alarm Configuration” mode allows choose whether the iTX’s datalogger will log continuously Alarm you to configure whether the iTX gas alarms will latch or Configuration or only after the unit has gone into gas alarm. -
Page 13: Next Calibration Dates
Next Calibration ALIBRATION ATES ACKLIGHT Dates Backlight The “Next Calibration Dates” mode allows you to set the The “Backlight Shut-Off” mode allows you to control Shut-Off 30 Days frequency of calibration in terms of days. The default whether the backlight shuts off automatically or manually. setting is 30 days but the value is fully adjustable. -
Page 14: Active Site
• After 5 seconds if no iButton is detected, the instrument will beep Industrial Scientific further recommends that a full and let you know it failed reading the iButton. It will then go back instrument calibration be performed using a certified to the initial Active Site screen. -
Page 15: Standard Calibration
TANDARD ALIBRATION UICK ALIBRATION Quick Cal To calibrate the iTX, press until “Zero Sensors” If the Quick Cal feature of the iTX has been enabled, all appears. Press to begin the zeroing process. All sensors capable of being calibrated using a multi- 100 ppm 100 ppm toxic and combustible sensors will be reset to zero during... -
Page 16: Using The Hand Aspirated Pump
The iSP is a parasitic sampling pump, meaning it operates AINTENANCE without a dedicated battery and draws its power from the With normal routine maintenance the iTX can be relied iTX itself. To use the iSP, simply slide it over the top end of upon to provide years of reliable service. -
Page 17: Pecifications
ROSS ENSITIVITY HART alkaline pack; all sensors installed; room Industrial Scientific has designed the iTX to respond as temperature; and no alarms activated. specifically as possible to the target toxic gas. Alkaline batteries, without parasitic pump 12hr Realistically, total specificity cannot be achieved in all Alkaline batteries, with parasitic pump cases. -
Page 18: Replacement Parts
& R EASURING ANGES ESOLUTION EPLACEMENT ARTS Range Resolution ITEM. PART NO. DESCRIPTION 999 ppm 1 ppm 17102484 iTX Main PCB Version 2.X 499 ppm 1 ppm (17088667 for Version 1.X) 99.9 ppm 0.1 ppm 17105255 iTX Sensor PCB Version 2.X 99.9 ppm 0.1 ppm (17090473 for Version 1.X) -
Page 20: Warranty
Industrial Scientific Corporation accepts no responsibility for HEREUNDER WHETHER SUCH CLAIM IS PLEADED IN its use by any means or in any way whatsoever Industrial Scientific CONTRACT OR IN TORT, INCLUDING STRICT LIABILITY Corporation shall not be liable for any expenses, costs by damage that may result from the use of the information contained within this IN TORT.
Need help?
Do you have a question about the iTX1709-5753 and is the answer not in the manual?
Questions and answers