Related Manuals for Salamander Pumps HomeBoost
Summary of Contents for Salamander Pumps HomeBoost
- Page 1 Pump installation and warranty guide for HomeBoost ™ Patented Product ISSUE 3 January 2015 x142741_SP_p5_vw.indd 1 09/01/2015 12:43...
- Page 2 If your installation is complicated or you have any questions, please consult the PumpWise Technical Helpline immediately (0191 516 2002). Additional help can also be found on the HomeBoost website www.home-boost.co.uk We encourage installers to consult the Salamander helpline before installation, where our engineers can give you professional advice regarding installation.
- Page 3 Contents Pre-installation checklist Application notes Typical installations Commissioning General specifications Lighting codes & Trouble shooting Fittings Kit PumpWise and warranty To the installer Terms and conditions x142741_SP_p3_lh.indd 3 17/12/2014 10:35...
- Page 4 Never fit the pump to communal risers and outlet Never pump directly from or to another Pipework above and below the pump must pump – only one HomeBoost ™ may be be securely fixed to the wall installed per household supply Only one HomeBoost ™...
- Page 5 ™ water inlet to the combi boiler as indicated in All outlets which are located between the the pre-installation checklist. mains stop tap and the HomeBoost ™ must be protected by non-return valves. This is to Never fit to communal risers (e.g. block of...
-
Page 6: Electrical Requirements
3A fused mains spur the polymer pump body. without invalidating the warranty. Figure 1: Spanner flats to hold the HomeBoost ™ during installation Spanner flats on brass pump housing... - Page 7 Typical installations Figure 2: Inlet and outlet Figure 5: Typical installation locations NOTE: Refer to pre-installation checklist for suitability Outlet Combi-boiler Combi-boiler Inlet Figure 3: Ideal location Figure 6: Earth continuity (4mm earth connection cable) Isolating Combi-boiler Ball valve Isolation valve for combi-boiler Tap connector Tap connector...
- Page 8 Before you finish 1 Connect pump pipe work • Check the pump inlet filter is fitted 2 Check that all isolating valves are open • With the HomeBoost installed, flush the ™ 3 Turn mains water on at the stop tap...
-
Page 9: Specifications
2 off 22mm x 15mm compression reducer sets Initiation Applications Fully automatic, water flow operated, requiring The HomeBoost pump is designed to boost ™ 3 litres per minute flow rate to initiate. low mains water pressure into a domestic... -
Page 10: Trouble Shooting
Then re-attempt start up routine Natural flow >12lpm Diagonal flash, Normal Pump Function ™ Pump starts and Sufficient mains water flow HomeBoost not required to run at this time. Pump will only lights flash diagonally run during periods of low water flow Reduced/... - Page 11 Fittings Kit Contents 1 x Ball valve 1 x tap connector 2 x reducer ¾” Tap connector x ¾” Tap connector x 22mm x 15mm 22mm compression 22mm compression compression reducer Fitting Instructions Flat Flat washer washer WHOLE HOUSE WHOLE HOUSE COMBI ONLY COMBI ONLY connector...
- Page 12 Please read the and guidance. full terms and conditions opposite. • Two year’s warranty – The HomeBoost pump comes with a ™ return to factory two year warranty. Our PumpWise commitment...
- Page 13 To the installer Please follow the guidelines for the contained within the installation and warranty guide and/or provided by the Salamander help desk. installation provided in this brochure and call b You are the original purchaser of the equipment from a the PumpWise helpline for installation advice.
- Page 14 Notes x142741_SP_p2_lh.indd 14 16/12/2014 15:11...
- Page 15 x142741_SP_p2_lh.indd 15 16/12/2014 15:11...
- Page 16 Salamander Pumped Shower Systems Limited Unit 2c Colima Avenue, Sunderland, SR5 3XE Tel: 0191 516 2002 Fax: 0191 548 4445 Email: service@salamanderpumps.co.uk x142741_SP_p2_lh.indd 16 16/12/2014 15:11...
Need help?
Do you have a question about the HomeBoost and is the answer not in the manual?
Questions and answers