Advertisement
Quick Links
Advertisement
Related Manuals for ADENDORFF ML392CI
Summary of Contents for ADENDORFF ML392CI
- Page 1 MODEL ML392CⅠ MULTIPLE USE WOODWORKING MACHINE SERVICE MANUAL...
- Page 2 CAUTION 1 To adjust and maintain after stopping the machine and take the plug off the socket. 2 Fix the milling hood when carriage, surface planing, press planing, sawing and storage (see below Fig). milling hood 3 To mount the protective device during the milling operation. 4 To dismount sawblade if you have to operate the press planing, milling and drill for a long time. ...
- Page 3 Model ML392CⅠmultiple use woodworking machine is widely used for its multiple functions such as surface planing, press planing, sawing, milling, drilling. Its main advantages are not only multiple purpose in usage but also light in weight, simple operation and easy maintenance, it may be used to process all kinds of woodpieces in house building, furniture making, decoration, wood arts and crafts making. ...
- Page 4 Press Planing Infeed 83.0dB(A) Max. level-LpeaK dB less than 110 Outfeed 87.5dB(A) Max. level-LpeaK dB less than 110 2.2 Residual Dust Average value of the residual dust Average value of the residual dust during workpiece feeding during workpiece outfeeding Surface planning 0.32mg／m Surface planning 0.42mg／m Press planning 0.12mg／m Press planning 0.15mg／m...
- Page 5 8 onto the drilling table 9 and milling table 7 separately. Screw the level moving bolt 27 into sliding base 29 and make it connected with the open ended screw arbor base of the supporter Fig.1 Overall Diagram 1.motor 2.lock bolt 3.graduated disk 4.presser 5.sliding table 6.guide7.saw hood 8.lock bar 9.splitter 10.saw table 11.outfeed table 12.limiting rubber 13.track 14.supporter 15.press planing table 16.planing lock bar 17.auto-feeding bar 18.elevating handle 19.bolt M8×30 20.bearing base 21.V-belt A900 22.bolt M8×50 23.bolt M8×50 24.V-belt A800...
- Page 6 Fig.2 Lifting diagram Fig.3 Ground bolt fixing diagram 5 Electric part 5.1 Electric diagram see Fig.7 a or b 5.2 Caution Pay attention to the voltage, frequency. They should be accommodated with the requirement and the difference should be not more than ± 5 ％ , and earthed dependably. You can use single phase or three phase motor for the machine.
-
Page 7: Safety Rules
Fig.4Drilling & Milling diagram 1. hex-head bolt M8 × 25 2.milling arbor 3.milling hood 4.cutter block 5.spacer 6.nut M18 anti-clockwise 7.milling table 8.push presser (group) 9.drilling table 10.locate fence 11.presser (group)-12. adjustable screw 13. nut M6 14. hex-head bolt M6×12 15. large spacer 6-140HV 16.press case 17.poke rod 18.hex head bolt M6×16 19.spacer 6-140HV 20.hex-head blot M8×16 21.post rod 22.column guide 23.column guide 24.saddle 25.set hoop 26. - Page 8 Fig.5 Crosscutting diagram 1.guide lock bar 2.guide part 3.woodpiece 4.saw hood 5.saw table 6.presser 7.dial scale 8.crosscut table 9.screw M10×20 10.press plate 11.track 12.square iron 13.distance case 14.bolt M8×75 Fig.6 Guide mounting and adjustment diagram 1.front bench 2.bolt M6×12 3.ruler base 4.lock lever 5.guide base 6.guide...
- Page 9 Fig.a Fig.b Single-phase motor electric element list (see Fig. a), Three-phase motor electric element list (see Fig. b) Type & specification Code Name Amount Fig. a Single-phase motor Fig.b Three-phase motor Plug Single-phase three pole 16A Three-phase four pole 380V／15A Fuse RT14-20 RT14-20...
- Page 10 NEVER INTRODUCE HANDS, ARMS, HEAD OR OTHER PARTS OF THE BODY INTO THE MACHINE, ESPECIALLY INTO THE ● MACHININH AREA OF THE ROTATING TOOL. THE WORKIMG AREA MUST BE WELL-ILLUMINATED. WITHOUT OBSTACLES, CLEAN AND WITHOUT PERSONS IN IT. ● NEVER LET KEYS, TOOLS OR WORKPIECES ON THE MACHINE; KEEP THE MACHINE TABLES ALWAYS CLEAN. TAKE THE PLUG OFF THE SOCKET AFTER STOPPING THE MACHINE. ...
- Page 11 Fig.8 Cutter mounting and adjustment diagram 1.straight ruler 2.back bench 3.cutter 4.tool presser 5.bolt M8×10 6.arbor 7.front bench Keep the blade in the middle, put the ruler 1 on the back bench 2, rotate the arbor 6, adjust ● the length of the knives above the surface of the bench until it can reach the ruler1 on the back bench 2.
- Page 12 Fig.9 Surface planing diagram (for wide workpiece) 1.spindel hood 2.bridge guard supporter 3.bridge guard 4.front bench 5.ruler base 6.lock lever 7.sawing and planing guide 8.lock lever 9.sawing safety hood 10.sawing table 11.emergency stop switch Fig.10 Surface planing diagram (for thin and thick workpiece) 1.spindle hood 2.bridge guard supporter 3.bridge guard 4.front bench 5.
- Page 13 Operator should stand at the position of Fig.9. Instructions for use ● Always advance the wood uniformly and slowly. ● Check that the wood doesn't have splittings or dangerous knots and always pass the ● concave part towards the tables. Avoid to pass short and small-dimensioned workpieces and, if necessary, use special flat ●...
- Page 14 Adjust the press planing table 3 according to the workpiece height to be obtained. Lock the ● table well after adjustment. For finishing passes, give a removal of about 1mm. Insert the wood driving rollers by pulling out lever. ● The operator should stand at the position of Fig.11. ...
- Page 15 Remove flange and blade, clean it well. ● Mount blade and lock nut again, screw the lock nut tightly, down the bench and lock it. ● Center the splitter knife. If not, loose the fixing nut, adjust it. ● Preparation Turn-off the machine and take the plug off the socket.
- Page 16 1.drill bit 2.drill hood 3.bolt M8 × 12 4.front bench 5.ruler base 6.arbor cover7.lock lever 8.sawing & planing guide 9.lock lever 10.saw safety cover 11.sawing table let the cutters extend over the toolpan at the same height, when straight edge cutter need to be mounted, the diameter of cutter edge is 74mm, when shaped edge cutters need to be mounted, the max.
- Page 17 Fig.14 Switch mounting diagram 1.change over switch 2.switch button 3.left wall board Turn-off the machine and take the plug off the socket. ● Cover the arbor by cover. ● Mount drill bit 1 and tighten by lock screw (Fig.13). ● Caution: The max.
- Page 18 Mount hood 2 and fix it by screw 3 (M8×12 see Fig.13). ● Make marks on workpiece before drilling, then clip the work piece on bench. ● Adjust the height and position of bench 7 by handwheel 32 (Fig.4). ● Operate the lateral and longitudinal handles.
- Page 19 11 Maintenance & attendance 11.1General maintenance Take the plug off the socket. Completely shut off the electric resource. ● Clean the wood chips after work. Don't use iron brush on the anti-kickback jaws. ● Lubricate rotate part every month, apply grease on chain, gear, nut and bushing with ●...
- Page 20 14 Machine Faults & Repairing Measures Take the plug off the socket before repairing and shut off the electric source Fault Reason Repairing Measure a. AC supply not electrified or the a. Check the power source The motor does not fuse has been blown and fuse revolve although its...
- Page 21 LNo.20060115T03-M2.5...
Need help?
Do you have a question about the ML392CI and is the answer not in the manual?
Questions and answers