Advertisement
Quick Links
E3
3" Elima-Matic Bolted Metallic
with Metallic Center Section
E3 Metallic Pumps
• Stainless Steel
• Alloy C
VERSA-MATIC
®
• Warren Rupp, Inc. • A Unit of IDEX Corporation
800 North Main Street, Mansfield, OH 44902 USA • Phone: (419) 526-7296 • www.versamatic.com
© Copyright 2017 Warren Rupp, Inc. All rights reserved
Advertisement
Related Manuals for Versa-Matic E3
Summary of Contents for Versa-Matic E3
- Page 1 3" Elima-Matic Bolted Metallic with Metallic Center Section E3 Metallic Pumps • Stainless Steel • Alloy C VERSA-MATIC ® • Warren Rupp, Inc. • A Unit of IDEX Corporation 800 North Main Street, Mansfield, OH 44902 USA • Phone: (419) 526-7296 • www.versamatic.com...
- Page 2 Safety Information IMPORTANT WARNING When used for toxic or aggressive fluids, the pump should Read the safety warnings and instructions in this manual always be flushed clean prior to disassembly. before pump installation and start-up. Failure to comply with the recommendations stated in this manual could damage the pump and void factory warranty.
- Page 3 Table of Contents SECTION 1: PUMP SPECIFICATIONS ....1 • Nomenclature • Performance • Materials • Dimensional Drawings SECTION 2: INSTALLATION & OPERATION ..7 • Principle of Pump Operation • Typical Installation Guide • Troubleshooting SECTION 3: EXPLODED VIEW ......10 • Composite Drawings •...
- Page 4 C Carbon Steel w/ PTFE O-Rings OB Oil Bottle H Alloy C w/ PTFE O-Rings T PTFE Encapsulated Silicone O-Rings Y FDA Santoprene *More than one option may be specified for a particular pump model. versamatic • Model E3 Bolted Metallic e3mdlHsmATEXMB-rev0317...
- Page 5 Commonly referred to as 316 Stainless Steel in the pump industry. For specific applications, always consult the Chemical Resistance Chart. Model E3 Bolted Metallic • versamatic e3mdlHsmATEXMB-rev0317...
- Page 6 Performance E3 - 3” Bolted Stainless Pump – Metallic Center Displacement Per Stroke, 1.46 Gal. (5.5 L) ELASTOMERIC AND TPE FITTED - RUGGED AIR CONSUMPTION IN SCFM 60 80 AIR PRESSURE IN PSI Flow Rate SCFM M 3 /HR Adjustable to ..0-273 gpm (1,033 lpm) Port Size Suction .
- Page 7 3/4" NPT Stainless Steel Centers ONLY AIR INLET 11.00 36.26 32.32 24.94 AIR EXHAUST 1" NPT 14.92 4.44 4X .50 SUCTION PORT 3" 150# ANSI / DIN FLANGE 14.13 4X .60 11.00 9.50 36.26 2.88 17.00 Model E3 Bolted Metallic • versamatic e3mdlHsmATEXMB-rev0317...
- Page 8 Dimensional Drawings E3 Bolted Metallic Dimensionally Interchangeable with Versa-Matic Clamped Pumps Dimensions in inches (metric dimensions in brackets). Dimensional Tolerance .125" (3mm). 1/2" NPT 1/2" NPT 3/4" NPT Stainless Steel Centers ONLY 3/4" NPT Stainless Steel Centers ONLY AIR INLET...
- Page 9 3/4" NPT Stainless Steel Centers ONLY AIR INLET AIR EXHAUST AIR EXHAUST SUCTION PORT MADE FROM UNLESS OTHERWIS SPECIFIED TOLERANCES MATERIAL MATERIAL .XXX SURFACE FINSH PUMP REFERENCE PUMP REFERENCE DIMENSIONS ARE INC DATE DATE DATE DATE Model E3 Bolted Metallic • versamatic e3mdlHsmATEXMB-rev0317...
- Page 10 (flooded suction condition), pipe the exhaust higher than the product source to prevent siphoning spills. 1" DIAMETER AIR EXHAUST PIPING LIQUID LEVEL SUCTION LINE versamatic • Model E3 Bolted Metallic e3mdlHsmATEXMB-rev0317...
- Page 11 To start the pump, slightly open the air shut-off valve. After the pump primes, the air valve can be opened to increase air flow as desired. If opening the valve increases cycling rate, but does not increase the rate of flow, cavitation has occurred. The valve should be closed slightly to obtain the most efficient air flow to pump flow ratio. Model E3 Bolted Metallic • versamatic e3mdlHsmATEXMB-rev0317...
- Page 12 Inspect check valves and seats for wear and proper setting. Replace if necessary. Entrained air or vapor lock in chamber(s). Purge chambers through tapped chamber vent plugs. For additional troubleshooting tips contact After Sales Support at service.warrenrupp@idexcorp.com or 419-524-8388 versamatic • Model E3 Bolted Metallic e3mdlHsmATEXMB-rev0317...
- Page 13 Composite Repair Parts Drawing - Elastomeric and TPE Fitted DOME DIAPHRAGM ASSEMBLY DROP IN MANIFOLDS DOME DIAPHRAGM ASSEMBLY DROP IN MANIFOLDS ME DIAPHRAGM ASSEMBLY DROP IN MANIFOLDS DROP IN MANIFOLDS Model E3 Bolted Metallic • versamatic e3mdlHsmATEXMB-rev0317...
-
Page 14: Me Diaphragm Assembly
PTFE V455TF V456TF Santoprene V305TPEXL V455TPEXL V456TPEXL Hytrel V305TPEFG V455TPEFG V456TPEFG Geolast V305G Stainless Steel SV456 (see note 1) Notes: 1.) These O-Rings are only needed with the stainless steel valve seat SV456 versamatic • Model E3 Bolted Metallic e3mdlHsmATEXMB-rev0317... -
Page 15: Drop In Manifolds 3
PTFE BONDED DIAPHRAGM ASSEMBLY METAL SEAT ASSEMBLY DROP IN MANIFOLDS PTFE BONDED DIAPHRAGM ASSEMBLY DROP IN MANIFOLDS DISCHARGE END SUCTION END ON END METAL SEAT ASSEMBLY BONDED DIAPHRAGM ASSEMBLY EMBLY DROP IN MANIFOLDS DROP IN MANIFOLDS Model E3 Bolted Metallic • versamatic e3mdlHsmATEXMB-rev0317... - Page 16 Foot Bracket(for SV352FB only)-Not Shown SP55-390 Notes: 1.) (4) SV456 valve seats can be used as an alternative to the PTFE seats. 2.) These O-Rings are only needed with the stainless steel valve seat SV456 versamatic • Model E3 Bolted Metallic e3mdlHsmATEXMB-rev0317...
- Page 17 Versa-Matic warrants to the original end-use purchaser that no product sold by Versa-Matic that bears a Versa-Matic brand shall fail under normal use and service due to a defect in material or workmanship within five years from the date of shipment from Versa-Matic’s factory.
- Page 18 EC / EU DECLARATION OF CONFORMITY The objective of the declaration described is in conformity with the relevant Union harmonisation legislation: Directive 94/9/EC (until April 19, 2016) and Directive 2014/34/EU (from April 20, 2016). Date of Issue: 10 May 2014 Technical File No.: 203104000-1410/MER Quality System Registration No: ISO 9001-2000 Conforming Apparatus: Air-Operated Metal Double Diaphragm Pumps for Use In Potentially Explosive Atmospheres...
-
Page 19: Model E3 Bolted Metallic
AIR CHAMBER (STAINLESS) P34-111NP AIR CHAMBER (NICKEL PLATED) P34-111TC" AIR CHAMBER (PTFE COATED)" P24-106 PILOT VALVE RING P24-107 PILOT VALVE O-RING P24-108 JAM NUT P34-104 PILOT SHAFT "P34-105 "THREADED BUSHING (BRASS) SP34-105" THREADED BUSHING (STAINLESS)" Model E3 Bolted Metallic • versamatic e3mdlHsmATEXMB-rev0317...
Need help?
Do you have a question about the E3 and is the answer not in the manual?
Questions and answers