68C3 Operations Manual - North Atlantic 68C3 Operation Manual

datasheet update. 11) H2 module update - description and control
mapping. 12) DLV descriptions - clarified "phase lock" definition. 13)
P4 ,K9 PCI/VME map update - pending PCI/VME for D6, P5
2013-03-03- ECO C02038; 1: D/S, DLV module code designation: Update AC
1435 Reference input voltage range specifications for D/S and D/L stimulus
module/channels - LV (2-28 Vrms) REF input range from: 2-115 to: 2-
28; HV (29-90 Vrms) REF input range from: 2-115 to: 10-115; added
module types (1R, 1T, 3N, 3P, 6T, 6U). 2: K9, K6 module description -
clarified principle of operation/block diagram. 3: NIU1 Description -
correction to J2 Port 2 Ethernet connection pinouts. 4: Clarified NIU1
specification (base) power (from 5.1W to 3.3W) 5: 75SBC4 - clarified
reference 'associated documents' are embedded within the specific
BSP. 6: 65CS4 - pg. 12, clarified Input Ref Voltage Sim Command
description - removed descriptor "Does not apply when Reference
Source is Internal". 7: Added KN, KL relay module(s)
specifications/description/register mapping to associated MFIO
platforms. 8: Added K7 and V1, V2 module support details. 9: SIU6
HW manual Corrected J3-67 pinout from: A-P0-23Z to: A-P2-23Z (pg.
21). 10: 65CS4 ops manual updated.
2012-12-20- 1. 64EP3, 64D3 Ops Manual(s) - clarified pinout(s) for MOD5 U3 and
1534 Ethernet keep-out. 2. Clarified 3-CH D/S and DLV module/channel
power on command word
2012-11-20- 1. NIU1 Operations Manual - Initial Agile release; 2. Gen3 module(s)
1328 minor format changes only; 3. 3 CH D/S and D/LV VME register maps
updated for correct on-board volt/frequency locations; 4. Clarified D/A
FIFO clock rate at 390.625 KHz only (removed 'pending', defined as
'not implemented); 5. E7 description - clarified counter pre-load "low"
register; 6. 64EP3/75DP3 - Data sheet and P/N Designation U3 Gig-E
rear port A clarification.
2012-08-22- 1) 64EP3; Data Sheet / P/N Designation: Redefined/swapped Ethernet
1324 option (B) MB and U3 locations. 2) SIU6; HW Manual:
Redefined/swapped Ethernet option (4) MB and U3 locations. 3) 76C2
Conn I/O Pinout - no content changes (Agile link only). 4) 67C3 Data
Sheet/Spec/Manual: Added mech. option J and K; 67C3/68C3 P/N
High Voltage operating warning note (P/N designation). 5) KA module
correct/re-define discrete voltage thresholds from 100mV to 10mV lsb.
Discrete I/O and A/D signal return references clarified (Description and
Conn I/O Pinout sub-docs). 6) "C*" module VME memory map - added
missing CH8 FIFO Buffer-Lo Threshold register. 7) P8-PC module
description; removed reference to VME specific register reference,
Interface Levels (Description sub-doc). 8) 75C3 - Added E7 to P/N
Designation subdoc. 9) 44PA1 - Added mechanical options B4, B5.
10) C* module description paragraph restructured.
2012-07-06- 1. Clarify MFIO card Ethernet protocol description 2. 64DP3 part
0935 number designation expanded for combination U3 and H2 Ethernet
port configurations (manual, spec, datasheet) 3. CANBus (P6) module
bit rate register programming example added (description section). 4.
Corrected minor margin format mis-registrations (module
specifications (C*, D7, F/J, K6). 5. RTD (G4) correct typo BIT INT
enable register from E0 to E8 (VME, PCI x 2). 6. SIU6 HW manual,
correct typo, debug/download mating connector from KMDLX-8P to
KMDLAX-8P. 7. Corrected typo 75C3 connector/pin-out section Front
Panel BIT LED call-out function.
2012-06-01- KA module - A/D channel data presentation/format clarification in
1632 description section.

68C3 Operations Manual

Rev: 2014-12-19-0947
North Atlantic Industries, Inc.
www.naii.com
Revision Page
AS 03/03/13
LB 12/20/12
LB 11/20/12
LB 08/22/12
AS 07/06/12
AS 06/01/12
12/19/2014
Page 328 of 330