Hilti SID 22-A Manual
Cordless impact screwdrivers
Hide thumbs
Also See for SID 22-A:
- Original operating instructions (18 pages) ,
- Manual (24 pages) ,
- Operating instructions manual (21 pages)
Related Manuals for Hilti SID 22-A
Summary of Contents for Hilti SID 22-A
- Page 1 SID 14A SID 22A SIW 14A SIW 22A English Printed: 27.07.2016 | Doc-Nr: PUB / 5293001 / 000 / 00...
- Page 2 Printed: 27.07.2016 | Doc-Nr: PUB / 5293001 / 000 / 00...
- Page 3 Direct current (DC) 1.4 Product information Hilti products are designed for professional use and may be operated, serviced and maintained only by trained, authorized personnel. This personnel must be informed of any particular hazards that may be encountered. The product and its ancillary equipment may present hazards when used incorrectly by untrained personnel or when used not as directed.
- Page 4 The type designation and serial number are printed on the type identification plate. ▶ Write down the serial number in the table below. You will be required to state the product details when contacting Hilti Service or your local Hilti organization to inquire about the product. Product information...
- Page 5 tool cannot be guaranteed. If any parts are damaged, have these parts repaired before using the tool. Many accidents are caused by poorly maintained power tools. ▶ Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edges are less likely to jam and are easier to control.
- Page 6 ▶ If the battery is too hot to touch, it may be defective. In this case, place the power tool in a non-flammable location, well away from flammable materials, where it can be kept under observation and left to cool down. Contact Hilti Service after the battery has cooled down. Printed: 27.07.2016 | Doc-Nr: PUB / 5293001 / 000 / 00...
- Page 7 Printed: 27.07.2016 | Doc-Nr: PUB / 5293001 / 000 / 00...
- Page 8 Printed: 27.07.2016 | Doc-Nr: PUB / 5293001 / 000 / 00...
- Page 9 3 Description 3.1 Product overview Printed: 27.07.2016 | Doc-Nr: PUB / 5293001 / 000 / 00...
- Page 10 The product described is a hand-held cordless impact screwdriver. It is designed for driving and removing screws and for tightening and releasing nuts and bolts in wood, metal, masonry and concrete. ▶ For this product use only Hilti Liion batteries of the B14 (SID/SIW 14A) or, as applicable, the B18 or B22 (SID/SIW 22A) series.
- Page 11 SID 14A SIW 14A Large high-strength bolts M6 to M12 M6 to M12 Socket/bit drive ″ hex. socket with lock- ″ square drive with ing ring ball-notch retention ″ square drive with locking ring SID 22A SIW 22A Rated voltage 21.6 V 21.6 V Weight (including battery and chuck)
-
Page 12: Operation
SIW 14A SIW 22A 1/2″ square 3/8″ square 1/2″ square 3/8″ square drive with ball- drive with drive with ball- drive with notch reten- locking ring notch reten- locking ring tion tion Torque Setting I 59 ftlb 48 ftlb 66 ftlb 55 ftlb (80 Nm) (65 Nm) - Page 13 Note The belt hook allows the power tool to be attached to a belt worn by the operator. The belt hook can be fitted to allow attachment on the left or right side of the body. ▶ Fit the belt hook. 5.3 Fitting an accessory tool SID 14A SID 22A...
- Page 14 1. Set the forward/reverse switch to the middle position or remove the battery from the power tool. 2. Pull the chuck ring forward and hold it in this position. 3. Pull the accessory tool out of the chuck. 4. Release the chuck ring. 5.5 Fitting an accessory tool SIW 14A SIW 22A...
- Page 15 1. Set the forward/reverse switch to the middle position or remove the battery from the power tool. 2. Pull the accessory tool off the square drive. 5.7 Setting the torque Technical data Model SID … (SID 14A OR SID 22A) ?? → page 9 Model SIW …...
- Page 16 ▶ Set the forward/reverse switch to the desired direction of rotation. 5.9 Screwdriving WARNING Risk of injury and damage. Screws/bolts or the workpiece may be damaged by excessively high torque; this may also lead to serious injury. ▶ Ensure that the fastener and attachment will withstand the level of torque generated by the tool. 1.
- Page 17 To help ensure safe and reliable operation, use only genuine Hilti spare parts and consumables. Spare parts, consumables and accessories approved by Hilti for use with the product can be found at your local Hilti Center or online at: www.hilti.com 6.2 Transport and storage of cordless tools...
-
Page 18: Troubleshooting
Most of the materials from which Hilti tools and appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, your old tools, machines or appliances can be returned to Hilti for recycling. Ask Hilti Service or your Hilti representative for further information. - Page 19 Printed: 27.07.2016 | Doc-Nr: PUB / 5293001 / 000 / 00...
- Page 20 Hilti = registered trademark of Hilti Corp., Schaan 20160701 Printed: 27.07.2016 | Doc-Nr: PUB / 5293001 / 000 / 00...
Need help?
Do you have a question about the SID 22-A and is the answer not in the manual?
Questions and answers