Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Coredy E300
Summary of Contents for Coredy E300
-
Page 1: Get Started
GET STARTED Coredy E300 Mini Range Extender/Aessess Point/Router... -
Page 2: Table Of Contents
Quick Installation Guide Preparing ................Setup Process ............... Web-Browser Method..........WPS - Method..............User Manual Overview................Using as a Extender............When to Use Your Extender........How the Extender Works..........Power on the Extender..........Connect to an Existing WiFi Network..... Method 1: Connect with a web browser.... Method 2:Connect with WPS ........ -
Page 3: Quick Installation Guide
1. Plug it into an electrical outlet ( closest to your primary router/WiFi access point ) 2. Use your Smart-Phone to connect with the repeater (find E300" and connect with it, if password request "Coredy try PIN number of the rear panel) 3. -
Page 4: Wps - Method
E300_EXT" and connect with it using the same password as of your primary router/AP. 9. If the internet works, unplug Coredy E300 and plug it halfway between your Router and the Device intended for the internet usage/dead zones in your home where you were getting low to no WIFI signals. -
Page 5: User Manual Overview
User Manual Overview The Coredy E300 WiFi Range Extender is a network device with multifunction, which can be using for increasing the distance of a WiFi network by boosting the existing WiFi signal and enhancing the overall signal quality over long distances. -
Page 6: Rear Panel
WAN/LAN LED Descriptions Power/WPS LED Lit amber. The E300 is starting. Blinking. Press and hold the WPS 3 seconds on the Rear Panel lets you use WPS to join the WiFi network without typing the WiFi password. The WPS LED blinks amber during this process. - Page 7 ) Best connection Repeater Good connection Poor connection WAN/LAN LED Lit amber. The E300 is starting. Blinking fast. The port is sending or receiving traffic. Off. No Ethernet cable is connected. LAN LED Lit amber. The extender has detected an Ethernet cable connection to the AP or other device.
-
Page 8: Using As A Extender
Using as a Extender When to Use Your Extender We recommend that you connect through the extender network only when the WiFi device is in a “dead zone” where connection from the existing network is poor or nonexistent. Data traffic routed through the extender is inherently slower than traffic routed directly from the network. -
Page 9: Power On The Extender
WiFi Range Extender Existing WiFi Boosts the range of your sometimes your router existing WiFi and creates does not provide the WiFi a stronger signal in hard coverage you need to reach areas. Power on the Extender Turn the Power On/Off button to “On” and Mode Switch Button to “Repeater”... -
Page 10: Connect To An Existing Wifi Network
Method 1: Connect with a web browser 1.Use a WiFi network manager on a computer or mobile device (recommended) to find and connect to the extender WiFi network “Coredy E300” , type the password (PIN number) on the label of rear panel extender if required. -
Page 11: Wireless Repeater Mode
Channel Security Your Target Network Name WPA2-PSK David WPA2-PSK Connect to Your Target Network Name Repeater SSID Coredy E300_EXT Security key The password of your Target Network Hide Password The Repeater Wreless key same as your Wireless AP/Router Apply Refresh... - Page 12 The extender creates a new extended WiFi network. The extender’s WiFi network name “Coredy E300_EXT”, use the same WiFi password that you use for your WiFi router. Note: If the extender doesn’t connect to the router, the WLAN LED 1 keeps blinking and the extender’s new WiFi network name doesn’t change to...
-
Page 13: Method 2:Connect With Wps
The location that you choose must be within the range of your existing WiFi router network. Use the WLAN LED 1 – LED 3 to help you choose a spot where the extender-to-router connection is optimal. 9. If only the WLAN LED 1 light amber , plug the extender into an outlet closer to the router and try again. - Page 14 2. Within two minutes, press the WPS button on your router or access point. When the extender connects to your existing WiFi network successful, the extender's new WiFi network name will change to “Coredy E300_EXT", and the WLAN LED1 - LED 3 will light amber (check the WLAN LED Descriptions on Page 5), confirm it on your computer or WiFi device.
-
Page 15: Connect An Ethernet-Enabled Device
The extender creates a new extended WiFi network. The extender’s WiFi network name “Coredy E300_EXT”, use the same WiFi password that you use for your WiFi router. Note: If the extender doesn’t connect to the router, the WLAN LED 1 keeps blinking and the extender’s new WiFi E300_EXT”... -
Page 16: Using As A Access Point
Using as a Access Point The Coredy E300 WiFi Range Extender also can be used as an Access Point, An access point receives data by wired Ethernet (such as hotel’s wired Ethernet), and converts to a 2.4Gig Hz wireless signal. It sends and receives wireless traffic to and from nearby wireless clients. -
Page 17: Cable Your Ap
3. Use a WiFi network manager on a computer or mobile device (recommended) to find and connect to the AP WiFi network “Coredy E300” , type the password (PIN number) on the label of rear panel AP if required. MAC:80:3F:5D:8A:7E:AA PIN:XXXXXXXX... - Page 18 8. Find and connect to the new converted WiFi network on your computer or WiFi device. The AP creates a new extended WiFi network. The AP’s new WiFi network name is “Coredy E300”, use the WiFi password that you set.
-
Page 19: Using As A Router
Using as a Router The Coredy E300 WiFi Range Extender also can be used as a Router. Prepare your modem unplug your modem's power. If it has a battery backup, remove the battery. Connect your modem, plug in your modem, Put the battery back in. - Page 20 We recommend that using a smart phone to connect with WiFi, the default WiFi network name is “Coredy E300”, type the password (PIN number) on the label of rear panel router if required. MAC:80:3F:5D:8A:7E:AA PIN:XXXXXXXX WLA N Pow er/W PS WAN /LAN 5.
- Page 21 Internet service providers offer a fixed IP address (static IP) Automatically obtain an IP address (dynamic IP) ADSL Dial-up (PPPoE) DSL_user name User Name DSL_password Password Hide Characters Coredy E300_EXT SSID Channel WPA/WPA2 Mixed Security Mode Password of WiFi Network Hide Characters Apply...
- Page 22 1) Place your router near the center of the area where your computers and other devices operate, and within line of sight to your wireless devices. 2) Make sure that the router is within reach of an AC power outlet and near Ethernet cables for wired computers. 3) Place the router in an elevated location, minimizing the number walls and ceilings between the router and your other devices.
-
Page 23: Change The Extender Settings
Change the Extender Settings To change the admin password 1. Launch a web browser. 2. Enter http://192.168.10.1/ http://ap.setup/ the address field of the browser login screen displays. 3. Enter admin for the user name and admin for the password, both in lowercase letters. The BASIC Home screen displays. -
Page 24: Save/Reload Your Extender Setting
4. Select the Time Zone Settings. Password Time Zone Settings Save/Reload Settings Upgrade Firmware Management Reboot Device 5. Enter the Current Date and Current Time in field, click Apply. Save/Reload your Extender setting You can use this feature to save your extender’s setting and reload it easy when you reset the router to factory setting or update the router firmware. -
Page 25: Update The Router Firmware
Update the Extender Firmware The extender firmware (routing software) is stored in flash memory. You might check if new firmware is available at www.coredytech.com and to update your product. 1. Launch a web browser. 2. Enter http://192.168.10.1/ http://ap.setup/ the address field of the browser login screen displays. -
Page 26: Hide Extender's Wireless Network
Hide extender's wireless network You can hide the wireless network that which is hidden and does not display in your wireless client’s scanning list, other people cannot join the wireless network if they don’t know your wireless network SSID name exactly. -
Page 27: Troubleshooting
Back Apply Back to home page TROUBLESHOOTING How to reset E300 to factory settings? Using a reset pin come with package to press and hold the Factory Reset button on the extender at least three the LAN and WAN/LAN Leds lights green. - Page 28 I am connected to Coredy E300_EXT and launched a browser, but I cannot log in the Setup Page/Web Management Page? Make sure that your computer is set up to use DHCP (most are). Relaunch browser type http://192.168.10.1/ http://ap.setup/ in the address field.
- Page 29 Keep moving the extender to outlets closer to the router until the full WiFi signal on smart phone. 4. Plug the extender into an electrical outlet in an elevated location and minimizing the number walls and ceilings between the router and your other devices.
- Page 30 DNS for you, configure your computer manually with a DNS address, as explained in the documentation for your computer, if you don’t know how to manually DNS, contact technical support www.coredytech.com/support or Google “how to manually set DNS windows 7” . Cannot Join a WiFi Network and Receive an Error Message? To join a WiFi network, you must know its network...
- Page 31 Sometimes extender’s WiFi connection between the WiFi router and the extender is poor. You can establish the best connection with a clear line of sight between the extender and the WiFi router. Make sure that no physical obstacles exist between the extender and the WiFi router, and try to move the extender closer to the WiFi router.
- Page 32 Mini Range Extender/Aessess Point/Router MODEL: Coredy E300 Toll Free US: +1-800-999-8470 (English Service) Mon-Fri 10:00-19:00 (CST) Toll Free UK: +44-808-134-9909 (English Service) Mon-Fri 15:00-01:00 (GMT) E-Mail: support@coredytech.com Website: www.coredy.com...
Need help?
Do you have a question about the E300 and is the answer not in the manual?
Questions and answers