1. Manuals
  2. Brands
  3. Samsung Manuals
  4. Monitor
  5. PPM63M7FS
  6. Service manual

Samsung PPM63M7FS Service Manual

Pdp-monitor
Hide thumbs Also See for PPM63M7FS:
Table of Contents

Advertisement

Quick Links

SERVICE
PDP-MONITOR
Refer to the service manual in the GSPN (see the rear cover) for the more information.
PDP-MONITOR
Chassis : D83A(NP_FHD)_Copernicus2
Model : PPM63M7FSX/EDC
Manual
1. Precaution
2. Product Specification
3. Disassembly & Reassembly
4. Troubleshooting
5. Exploded View & Part List
6. Wiring Diagram
7. Schematic Diagram
PPM63M7FS
CONTENTS

Advertisement

Table of Contents
loading

Related Manuals for Samsung PPM63M7FS

Summary of Contents for Samsung PPM63M7FS

  • Page 1 1. Precaution 2. Product Specification 3. Disassembly & Reassembly 4. Troubleshooting 5. Exploded View & Part List 6. Wiring Diagram 7. Schematic Diagram PPM63M7FS Refer to the service manual in the GSPN (see the rear cover) for the more information.
  • Page 2 Asia asia.samsungportal.com Mideast & Africa mea.samsungportal.com © Samsung Electronics Co.,Ltd. Dec. 2007 This Service Manual is a property of Samsung Electronics Co.,Ltd. Printed in Korea Any unauthorized use of Manual can be punished under applicable AA82-04956A International and/or domestic law.

  • Page 3: Table Of Contents

    Table of Contents 1. Precaution 1-1 Safety Precautions ..............................1-1 1-2 Servicing Precautions ..............................1-3 1-3 Static Electricity Precautions ............................1-4 1-4 Installation Precautions ...............................1-5 2. Product Specification 2-1 Product Specification ..............................2-1 2-2 Specifications Analysis ..............................2-3 2-3 Accessories .................................2-4 3. Disassembly & Reassembly 3-1 Overall Disassembly &...

  • Page 4: Precaution

    These two grounding systems are separated in the circuit using an unbreakable/unchangeable insulation material. 8. When any parts, material or wiring appear overheated or damaged, replace them with new regular ones immediately. When any damage or overheating is detected, correct this immediately and make a regular check of possible errors. Samsung Electronics...
  • Page 5 Critical safety parts should be bracketed with ( , ). Use only regular parts for replacements (in particular, flame resistance and dielectric strength specifications). Irregular parts or materials may cause electric shock or fire. Samsung Electronics...

  • Page 6: Servicing Precautions

    11. Due to the nature of plasma display panels, partial after-images may appear if a still picture is displayed on the screen for a long period of time. This is caused by brightness deterioration due to the storage effect of the panel, and to prevent this from happening, we recommend that the brightness and contrast are reduced. (e.g.) Contrast: 25, Brightness: 50 Samsung Electronics...

  • Page 7: Static Electricity Precautions

    These servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so. Samsung Electronics...

  • Page 8: Installation Precautions

    A rise in temperature within the product may cause fire. 8. When moving a PDP with removable speakers, detach the speakers first before moving the main body. Moving the PDP main body without separating the speakers may cause the speakers to detach, possibly causing damage or injury. Samsung Electronics...
  • Page 9 MEMO Samsung Electronics...

  • Page 10: Product Specification

    Product Specification 2. Product Specification 2-1 Product Specification Features Block Specification PDP Module Samsung SDI WF2 FHD (S63FH-XB01) Power Input Voltage : AC 100~240V, 50/60Hz Scaler Video SVP-WX68 Video Decoder Sound AMP NTP-3000 Sound Audio Codec SGTV5810 Cabinet M7 Design Specification Model...
  • Page 11 - The interlace mode is not supported. - The set might operate abnormally if a non-standard video format is selected. - Separate and Composite modes are supported. SOG is not supported. - HDMI is supported for DTV signals only. Samsung Electronics...

  • Page 12: Specifications Analysis

    1 Input/1 output Connections    HDMI    Scart    Optical    Coaxial    ※ For the power supply and power consumption, refer to the label attached to the product. Samsung Electronics...

  • Page 13: Accessories

    Accessories Item Item code Remark Remote Control BN59-00656A Batteries 4301-000103 Power Cord 3903-000042 Owner’s Instructions BN68-01364B Samsung Service center Warranty Card BN68-00514E Registration Card AA68-03575F Safety Guide Manual AA68-03242K Ferrite Cores for 3301-001201 Speaker Wire (2EA) PC Cable BN39-00115A S-VIDEO Cable...

  • Page 14: Disassembly & Reassembly

    ① Remove the 8 screws on the Bracket Bracket Terminal Terminal. ( : WSP,PH,+,M4,L8,ZPC(YEL),SWRCH1 ② Remove the 8 Hex nuts for the PC input. ( : M3,L6,NI PLT,SUM24L,#4-40 ③ Remove Bracket Terminal. ④ Remove the 2 screws on the Bracket Terminal. ( : BH,+,-,M3,L8,ZPC(BLK) Samsung Electronics...
  • Page 15 ③ Remove the PC MAIN and AV SUB Board. 3-1-5 Separation of FILTER-EMI AC LINE Part Name Description Description Photo ① Detach connector from SMPS. FILTER ② Remove 2 screws. ( AC LINE : FH,+,M3,L10,NI PLT,SWRCH18A,FP, ③ Remove a screw. ( : BH,+,S,M4,L8,ZPC(YEL) ④ Remove FILTER-EMI AC LINE. Samsung Electronics...
  • Page 16 ① Remove 3 screws. Cover- Rear Sub : BH,+,S,M4,L16,ZPC(BLK),SWRCH18A ② Remove 3 screw. : WSP,PH,+,M4,L8,ZPC(YEL),SWRCH1 ③ Remove the Cover-Rear Sub . 3-1-7 Separation of ASSY PCB MISC-CONTROL Part Name Description Description Photo Control ① Remove 3 screws. Board : RH,+,B,M4,L15,ZPC(BLK),SWRCH18 ② Remove the Control Board. Samsung Electronics...
  • Page 17 Specifically, avoid touching any part of the capacitor. 3-1-9 Separation of ASSY PDP MODULE P-LOGIC MAIN BOARD Part Name Description Description Photo ① Detach all connectors from the Logic Logic Board Main Board. ② Remove 4 screws. : PH,+,WWP,M3,L8,NI PLT,SWRCH18A ③ Remove the Logic Main Board. Samsung Electronics...
  • Page 18 Remove 6 screws. X-Main ① Board : PH,+,WWP,M3,L8,NI PLT,SWRCH18A, Remove the X-Main Board. ② X-Buffer ① Remove 6 screws. Upper & : PH,+,WWP,M3,L8,NI PLT,SWRCH18A, Lower Board ② Remove the X-Buffer Upper & Lower Board. Samsung Electronics...
  • Page 19 ① Detach all connectors from the Y-Main Y-Main Board Board. Remove 9 screws. ② : PH,+,WWP,M3,L8,NI PLT,SWRCH18A, ③ Remove the Y-Main Board. Y-Buffer Remove 8 screws. ① Upper & : PH,+,WWP,M3,L8,NI PLT,SWRCH18A Lower Board Remove the Y-Buffer Upper & Lower ② Board. Samsung Electronics...
  • Page 20 Board : PH,+,WWP,M3,L8,NI PLT ③ Remove the E, F, G-Buffer Board. ① Detach the all connectors from the buffer Lower Adrress board. Buffer ② Remove 12 screws. Board : PH,+,WWP,M3,L8,NI PLT ③ Remove the E, F, G-Buffer Board. Samsung Electronics...
  • Page 21 MEMO Samsung Electronics...

  • Page 22: Troubleshooting

    - Check to see if there is a disconnected or loose cable connection. - Check to see if the cables are connected according to the connection diagram. 2. Check the power input to the Main Board. 3. Check the voltage in and out between the SMPS ↔ Main Board, between the SMPS ↔ X, Y Main Board, and between the Logic Boards. Samsung Electronics...
  • Page 23 Main SMPS CN800 connected? connector and the Main SMPS CN801 connected ① Is the Fuse (F801S) of the Main SMPS Replace Fuse (F801S) Power Input Part blown? ② Main SMPS CN801 Pin 3 : STB 5V Pin 1 Replace the Main SMPS PS-ON : Check to see if it is 0V Replace the Main Board Samsung Electronics...
  • Page 24 X Main Board from the SMPS? ③ Does the symptom continue when Replace the connecting the power after removing CN807 Logic Board from the SMPS? Replace the Main SMPS WheN SeParaTINg aND CONNeCTINg The CaBleS SuCh aS CN807, CN808, CN809, CN810, CN811 Of The MaIN SMPS, CN4000 Of The X MaIN BOarD, aND CN5004 Of The Y MaIN BOarD, a SPark MaY Be geNeraTeD Caution BY The eleCTrIC Charge Of The hIgh CaPaCITY CaPaCITOr. TherefOre, WaIT SOMe TIMe afTer DISCoNNECTINg ThE PowER CoRD FRoM ThE uNIT. Samsung Electronics...
  • Page 25 Is the cable connection between the Main Cable Connection Board and the speaker properly connected? ② Replace the SMPS Check that the voltage of No.7,8 pin of SMPS CN801 has 18V Replace the Is the speaker output terminal of the Main Main Board Board normal? ③ Replace the Speaker Samsung Electronics...
  • Page 26 Abnormal Image (not open or short) is no screen Y-MaIN, X-MaIN, logic Main Sustain open Some horizontal lines don’t exist on screen Scan Buffer, fPC of X/Y Sustain Short Some horizontal lines appear to be linked on screen Scan Buffer, fPC of X/Y Address open Some vertical lines don’t exist on screen logic Main, logic Buffer, TCP Address Short Some vertical lines appear to be linked on screen logic Main, logic Buffer, TCP Samsung Electronics...
  • Page 27 F5004 for VCC F4004 for VDD F5005 for OUT_L F4005 for Ve Q4002~Q4003 SHORT SHORT Q5009~Q5021 FET/ Q4011~Q4016 FET/ D5005, D5007 Replace the Board Replace the Board DIODE D4004 DIODE D5008 D4006~D4008 Y-MAIN X-MAIN Normal State Normal State Samsung Electronics...
  • Page 28 F4002 for Vs FUSE Replace the Board FUSE Replace the Board F5004 for VCC F4004 for VDD F5005 for OUT_L F4005 for Ve SHORT SHORT Q4002~Q4003 Q5009~Q5021 Replace the Board Replace the Board Q4011~Q4016 Y-MAIN X-MAIN Normal State Normal State Samsung Electronics...
  • Page 29 ④ Sustain Short (some horizontal lines appear to be linked on Video) [ Y-FPC ] Sustain Short (Discharging in unwanted Scan line) After Changing Y-buffer, Replace the Panel recheck the status There a defect on FPC Done (Defect is from Y-buffer) Samsung Electronics...
  • Page 30 Buffer Board and the Logic Main address data output section. Check the FFC connection status Check the detailed waveform Replace Logic Main / and control the signal waveform Address Buffer (E or F) / DONE Replace the Panel Samsung Electronics...
  • Page 31 - Replace the Main board The OSD box appears but Incorrect program version there is no text. - Check the version of each program - Replace the Main board A blank upper (or lower) block upper/lower Y Buffer defect appears on the screen. - replace the corresponding upper/lower buffers 4-10 Samsung Electronics...
  • Page 32 A vertical green line appears on The SMPS voltage is incorrect the screen. - Adjust the SMPS voltage according to the voltage printed on the module label Dim screen (blurred in red) X-Main board defect - replace the X-Main board A blank screen appears - replace the Y-Main board Samsung Electronics 4-11...
  • Page 33 Corresponding Buffer Board block screen is blank 10 aSSY PDP MODule P-aDDreSS f Buffer Corresponding Buffer Board block screen is blank 11 aSSY PDP MODule P-aDDrSSS g Buffer Corresponding Buffer Board block screen is blank 12 aSSY PCB MISC-MaIN No Power, abnormal screen for each input source, PIP screen trouble, Sound trouble 13 aSSY BOarD P-fuNCTION The side function key does not work properly. ① ⑫ ⑬ 4-12 Samsung Electronics...

  • Page 34: Adjustment

    <If adjustment equipment is not available> ① write down the value of hDMI white Balance of Factory Mode before replacing Board. ② PDP Option of factory Mode → set the factory Data Type item as the suitable value of relevant model. ③ Set the value of hDMI white Balance with the value written down before. Samsung Electronics 4-13...
  • Page 35 12. r eset T-CP2MWWMf-XXXX Boot Merge : Ok T-SfrMWWS-XXXX DBg MODe SaffrON_Tr-XXXX Mon/Day/Year hout/Min/Sec ※ The version of the firmware displayed at the bottom of the screen may differ and the firmware is subject to change for the improvement of product functions. ※ If you have adjusted the settings in Service Mode, you have to reset the product. 4-14 Samsung Electronics...
  • Page 36 LNA Menu TTX On/Off TTX list Carrier Mute high Devi. Vol. Curve Small hDMI hotPlug hDMI Clk Ctrl hDMI hP Dly hotel option Shop Mode Color Space PC Ident Language English Ch. Table SuwoN TTX group Auto iDTV_Cntry PDP group S5e_DfMa Samsung Electronics 4-15...
  • Page 37 Troubleshooting 3. white Balance Item Range Sub Brightness 0~255 R-offset 0~255 g-offset 0~255 B-offset 0~255 Sub-Contrast 0~255 R-gain 0~255 g-gain 0~255 B-gain 0~255 4-16 Samsung Electronics...
  • Page 38 1 ComB filter : Y-filter - 80h 2 Sharpness Item Data h2gain h4gain V2gain V4gain Sr2gain Sr4gain Sl2gain Sl4gain Peakth1 Peakth2 2Fhq Sub Color 3 NR Item Data Y_Nr_Off C_NR_oFF Y_Nr_ON C_NR_oN 4 RgB Calibration Item Data R-offset g-offset B-offset R-gain g-gain B-gain Samsung Electronics 4-17...
  • Page 39 6 Calibration Target Item Data aV aDC CoMP ADC PC ADC ALL RgB 7 Color Management Item Data Skin Direction Reddish Skin Enhance green Stretch Blue Stretch 8 S ync Control Item Data hSync Tip End VSync agC Min VSync agC Max VSync Clamp Mode VSync Thresh 4-18 Samsung Electronics...
  • Page 40 Skin Enable hFunc-Basis Skin Tu Mean-offset1 Skin Tv Mean-offset2 M Skin Tu PDP Logic Pattern Select Panel Type Panel Inch 63 FhD Strengh Th Panel Version logic Sw Version 07Y 05M 02D Repeat Mode Panel Temp. DBg Markon Bypass L gain u gain Samsung Electronics 4-19...
  • Page 41 Data Item Data Video Mute Time D-watchDog Dynamic Contrast watchDog Dynamic Dimming uART Select Dynamic CE FBE Select fBe2X LNA PLuS Tuner Auto Magazine LNA Tuner Top Semco PixelShift Test Tuner Top Alps Debug D.gamma M.gamma 0_85 MJC/PDP frC All on 4-20 Samsung Electronics...
  • Page 42 Data wB Movie w1_BoFFS No_BoFFS Color Mode Movie w2_RgAIN C2_RgAIN Color Tone Cool1 w2_BgAIN C2_BgAIN MSub Brigh w2_RoFFS C2_RoFFS MSub Contr w2_BoFFS C2_BoFFS w1_RgAIN No_RgAIN Movie Contr w1_BgAIN No_BgAIN Movie Brigh w1_RoFFS No_RoFFS Movie Color Movie Sharp Samsung Electronics 4-21...
  • Page 43 1) Apply the 1080p Lattice (N0. 6) pattern signal to the Component IN 1 port 2) Press the Source key to switch to “Component1” mode 3) Enter Service mode 4) Select the “Calibration” menu 5) Select the “Comp Calibration” menu. 6) In “Comp Calibration Off” status, press the “ ” key to perform Calibration. 7) When Calibration is complete, it returns to the high-level menu. 8) You can see the change of the “Comp Calibration” status from failure to Success. 4-22 Samsung Electronics...
  • Page 44 Adjust spec. 1. Source: DVI 2. Setting Mode: 1920*1080@60hz 3. Pattern: Pattern #92 4. use equipment: MIk-7256 (MSPg925l) ( SAMSuNg whITE BALANCE Adjustment PATTERN with FPD ) 5. Work order 1 Connect DVI output terminal of MIk-7256 (MSPg925l) to the hDMI input in main set 2 Set the input to DVI mode 3 Enter the white Balance menu of service mode 4 Contact CA-210 sensor to glass filter...
  • Page 45 10,500 ( ± 0) 4-2-5 Replacements & Calibration * Check items listed after changing each Replaced assembly items Check Items ① Auto Program aSSY PCB MISC-MaIN ② white Balance Adjust aSSY PCB P-SMPS Vs, Va voltage check and adjust aSSY PDP MODule P-X MaIN aSSY PDP MODule P-Y MaIN aSSY PDP MODule P-lOgIC MaIN aSSY PDP MODule P-X MaIN SCaN uPPer aSSY PDP MODule P-X MaIN SCaN lOWer Not to be adjusted aSSY PDP MODule P-Y MaIN SCaN uPPer aSSY PDP MODule P-Y MaIN SCaN lOWer aSSY PDP MODule P-aDDreSS e-Buffer aSSY PDP MODule P-aDDreSS f-Buffer aSSY PDP MODule P-aDDrSSS g-Buffer ※ When replacing the SMPS or PDP panel, you have to check the voltage printed on the panel sticker and adjust it. 4-24 Samsung Electronics...
  • Page 46 1. after replacing the SMPS or PDP panel, you must adjust the voltage referring to the voltage label printed on the panel. (If you do not adjust the voltage, an abnormal discharge symptom may appear.) Value Board Adjustment SMPS Vset -185 Voltage label SMPS-MAIN 2. A point of adjusting SMPS-MAIN voltage. Va Adjustment Va Test Point Ve Test Point Ve Adjustment Vsc Test Point Vsc Adjustment Vs Adjustment Vs Test Point Samsung Electronics 4-25...
  • Page 47 Troubleshooting ■ Y-rr and Y-fr controls Test Point Test Point Set the main reset (rising : 60usec, falling : 80usec) by change the value of variable resistor. 60usec Rising ramp 60usec variable resistor Rising ramp variable resistor Falling ramp variable resistor Falling ramp variable resistor 80usec 80usec 4-26 Samsung Electronics...

  • Page 48: Upgrade

    Troubleshooting 4-3 Upgrade 4-3-1 How to update software 1. Preparing Items - Computer for downloading, PDP Monitor, rS232 cable (female to female, twisted pin no.2 – pin no.3) 2. Install the download program - execute a file “2M flashDownloader Setup.exe” Click “NeXT” Samsung Electronics 4-27...
  • Page 49 Troubleshooting Click “NeXT” Proceeding..Click “FINISh” 4-28 Samsung Electronics...
  • Page 50 3. Following below steps to update (start when disconnect a power cord) 1 Connect RS-232 IN jack and PC with RS-232 Cable. 2 excute a program “2MB flash Downloader Ver 0.9”. 3 Select Flash Size “2MB (M32C)”. 4 Click "open" and select Software code file “T-CP2MwwMF-1001.0.mot”. 5 Click “Connect”. 6 Connect power cord. Samsung Electronics 4-29...
  • Page 51 Troubleshooting 7 Click “Program and Verify” to update software code when program is “Ready” (it takes almost 10 minites.) 8 Complete. 9 Disconnect power cord to reset a SET. Connect a power cord and power on after 1 second. 0 restart first step, if you have any error when Downloading. 4-30 Samsung Electronics...
  • Page 52 MEMO Samsung Electronics 4-31...

  • Page 53: Exploded View & Part List

    Exploded View & Part List 5. Exploded View & Part List 5-1 PPM63M7FSX/EDC Exploded View Samsung Electronics...
  • Page 54 T0256 BN64-00153B DECORATION-BACK SPD-63P3H,ABS+PC,3.0,5V S.N.A T0268 3903-000042 CBF-POWER CORD DT,EU,FP3/YES,IEC320 C13/ T0312 BN96-00302E ASSY COVER P-REAR SUB 63M6H,,AL T1.5,,, T0456 BN67-00191A GLASS-FILTER EMI 63” W2 FHD,MRT,44%,1442 T0918 AA60-00110L SPACER-FILTER 63P3H,P/U FROM,1420,6.0,9. S.N.A T0918 AA60-00110M SPACER-FILTER 63P3H,P/U FROM,810,9.0,8.0 S.N.A Samsung Electronics...

  • Page 55: Ppm63M7Fsx/Edc Service Item

    T0162 BN96-04873A ASSY PDP P-X-MAIN SCAN LOWWER PL63FH001A T0163 BN96-04874A ASSY PDP P-Y-MAIN PL63FH001A,S63FH-XB01, T0164 BN96-04875A ASSY PDP P-Y-MAIN SACN UPPER PL63FH001A, T0165 BN96-04876A ASSY PDP P-Y-MAIN SACN LOWWER PL63FH001A T0312 BN96-00302E ASSY COVER P-REAR SUB 63M6H,,AL T1.5,,, Samsung Electronics...

  • Page 56: Wiring Diagram

    CN5502 CN2502 CN2600 CN2700 Y-BUFFER(LOW) E-BUFFER F-BUFFER G-BUFFER CN2500 CN2601 CN2701 CN2508 CN2708 CN2602 CN2503 CN2504 CN2505 CN2506 CN2507 CN2603 CN2604 CN2605 CN2606 CN2607 CN2703 CN2704 CN2705 CN2706 CN2707 CN2203_FHD MAIN BOARD CN1101 CN1401 AC-INLET FUNCTION CN1203 SPEAKER Samsung Electronics...
  • Page 57 Wiring Diagram ※ The code number of cable(Lead-connector) can be changed, see “5. Exploded View & Part List.” Code Photo LVDS BN39-00843C POWER BN39-00802C AC_INPUT 2901-001363 Samsung Electronics...
  • Page 58 Pin No. Signal Pin No. Signal FUNCTION NC(AUTO_V) GND_5.3V GND_12V Pin No. Signal PS_ON GND_5.3V GND_12V KEY_INPUT1 GND_STBY GND_5.3V GND_12V KEY_INPUT2 STBY GND_5.3V AGND GND_18V AMP 5.3V GND_18V AMP 5.3V 18V AMP 5.3V NC(FAN_DET) 18V AMP 5.3V NC(FAN_ON) Samsung Electronics...
  • Page 59 WP_PANEL LCD_ODD_TX3+ LCD_EVEN_TXCLK- LVDS_FORMAT LCD_ODD_TX4- LCD_EVEN_TXCLK+ DDC_CTRL_PANEL LCD_ODD_TX0- LCD_ODD_TX4+ LCD_EVEN_TX3- LCD_ODD_TX0+ LCD_ODD_TX5- LCD_EVEN_TX3+ LCD_ODD_TX1- LCD_ODD_TX5+ LCD_EVEN_TX4- CN1203(MAIN Board) CN800(SMPS) ↔ ↔ SPEAKER AC INLET Pin No. Signal Pin No. Signal R+_OUT AC N R-_OUT L+_OUT AC L L-_OUT Samsung Electronics...
  • Page 60 Connect E-Buffer with F-Buffer by signal. CN2602 CN2601 Connect F-Buffer with G-Buffer by signal. CN2701 CN811 Supply 5.3V, Va power to F-Buffer from SMPS. CN2708 CN1401 Connect Key_Input1, Key_Input2, LED, IR signals of function assy to Main board and supply 5V power. Samsung Electronics...
  • Page 61 MEMO Samsung Electronics...

  • Page 62: Schematic Diagram

    Connects to the Y terminal block, 1) provides maintaining voltage waveform (including ERC), 2) provides Y Rising, Falling Ramp waveforms, and 3) maintains the Vscan bias. ■ Address Buffer Board It delivers the data signal and control signal to the TCP. Samsung Electronics...
  • Page 63 MEMO Samsung Electronics...
  • Page 64 Schematic Diagram 7-2 Schematic Diagram 7-2-1 POWER This Document can not be used without Samsung’s authorization. Power Samsung Electronics...
  • Page 65 Schematic Diagram 7-2-2 SOUND PROCESS This Document can not be used without Samsung’s authorization. Power TP01 TP01 TP02 TP01 TP02 Samsung Electronics...
  • Page 66 Schematic Diagram 7-2-3 Input & Output Jack This Document can not be used without Samsung’s authorization. Power TP03 TP03 TP03 TP04 c t i TP04 Samsung Electronics...
  • Page 67 Schematic Diagram 7-2-4 MICOM This Document can not be used without Samsung’s authorization. TP01 Power ! ! ! TP01 TP01 Samsung Electronics...
  • Page 68 Schematic Diagram 7-2-5 SVP-WX(Scaler) This Document can not be used without Samsung’s authorization. TP01 Power TP01 TP04 TP04 TP01 Samsung Electronics...
  • Page 69 Schematic Diagram 7-2-6 DDR This Document can not be used without Samsung’s authorization. Power Samsung Electronics...

This manual is also suitable for:

Ppm63m7fsx/edc

Table of Contents