Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Setup Manual
Advertisement
Table of Contents
Related Manuals for Extron electronics SM 26
Summary of Contents for Extron electronics SM 26
- Page 1 User Guide Speakers SM 26 ® SpeedMount Surface Mount Speakers 68-2164-01 Rev. A 08 13...
-
Page 2: Safety Instructions
Safety Instructions Chinese Simplified Safety Instructions • English （简体中文） 警告： 产品上的这个标志意在警告用户该产品机壳内有暴露的危险 WARNING: This symbol, , when used on the product, is intended to 电压， 有触电危险。 alert the user of the presence of uninsulated dangerous voltage within the product’s enclosure that may present a risk of electric shock. 注... -
Page 3: Conventions Used In This Guide
NOTE: A note draws attention to important information. Specifications Availability Product specifications are available on the Extron website, www.extron.com. Copyright © 2013 Extron Electronics. All rights reserved. Trademarks All trademarks mentioned in this guide are the properties of their respective owners. The following registered trademarks , registered service marks are the property of RGB Sys-... -
Page 4: Table Of Contents
Contents Introduction ........... 1 About this Guide ..........1 About the SM 26 Surface Mount Speaker ..1 Features ............. 1 Application Diagram ........... 2 Installation ............. 3 Installing the Speaker Mounting Plate ....3 Mounting to a Wall Stud ........5 Yoke Mounting the SM 26 ........ -
Page 5: Introduction
This guide describes the Extron SM 26 surface mount speaker and discusses how to install, configure, and operate it. In this guide, the terms “SM 26” and “speaker” refer to the SM 26 surface mount speaker. About the SM 26 Surface Mount Speaker The SM 26 speaker is a surface-mount speaker system that features a 6.5-inch woofer... -
Page 6: Application Diagram
• Security key — A special key allows the speaker to be locked or unlocked to the mounting plate. Application Diagram The following diagram shows an example of how the SM 26 surface mount speakers can be connected. Extron TouchLink... -
Page 7: Installation
• Removing the Speaker from the Mounting Plate Installing the Speaker Mounting Plate The SM 26 speaker comes with a lat mounting plate and an adapter for positioning the speaker 10° up, down, left, or right. • 0° mounting plate — The flat (0°) mounting plate allows the speaker to be mounted flat on a suitable surface. - Page 8 The mounting plate can be installed vertically or horizontally, as shown below. Catch Tab Horizontal Mounting Vertical Mounting Positioning the Mounting Plate Figure 3. NOTE: Observe all applicable building codes and local ordinances when installing the speaker. SM 26 Surface Mount Speaker • Installation...
-
Page 9: Mounting To A Wall Stud
If not using the adapter, position the mounting plate against the wall. The #26 arrow molded into the mounting plate indicates the vertical midpoint of the SM 26 speaker when it is mounted on a wall stud. While positioning the mounting plate on the wall, mark the location of two pilot holes using the holes indicated below. - Page 10 The SM 26 can be mounted with or without the 10° mounting adapter. In either case the wiring of the quick connect contacts remains the same, but the wire routing will vary. Routing the wires without the 10° mounting adapter Route the speaker cable through the rear of the 0°...
- Page 11 NOTE: If surface mounting, route wires through alternate access points. – – 33-0000-01 Rev. Ax1 LOOP LOOP 10° Mounting Adapter 0° Mounting Plate Alternate Access Point Alternate Access Points Routing Wires Through Alternate Access Points Figure 9. SM 26 Surface Mount Speaker • Installation...
- Page 12 0.27” (7 mm) Good 0.47” (12 mm) Sceew Head Clearance Figure 10. Mounting Screws Attaching the Mounting Plate to the Wall Figure 11. SM 26 Surface Mount Speaker • Installation...
-
Page 13: Yoke Mounting The Sm 26
Yoke Mounting the SM 26 The SM 26 can be mounted using the optional yoke mount kit. Refer to the Yoke Mount Kit Setup Guide for installation details. Attaching a Secondary Support Cable If a secondary support cable is being attached, attach the cable to the eye bolt, as shown below. -
Page 14: Attaching The Speaker To The Mounting Plate
Attaching the Speaker to the Mounting Plate ATTENTION: By default, the SM 26 speaker is shipped unlocked. When mounting the speaker to the mounting plate, be sure that the speaker is unlocked. Failure to place the speaker in the unlocked position will result in damage to the speaker lock mechanism should an attempt be made to mount a locked speaker (see “Using... -
Page 15: Setting The Tap Selector Switch (Sm 26T Model Only)
Tap Indicator 8Ω for 70 volt 8Ω Tap Indicator for 100 volt Figure 14. Setting the Tap Selector Switch SM 26 Surface Mount Speaker • Installation... -
Page 16: Using The Security Key To Lock And Unlock The Speaker
Unlocked Unlocked Figure 15. Unlocking the Speaker Unlocked Locked Twist to Lock/Unlock Using the Security Key to Lock and Unlock the Speaker Figure 16. SM 26 Surface Mount Speaker • Installation... -
Page 17: Removing The Speaker From The Mounting Plate
Apply pressure to the grille with your finger over the “dimpled” keyhole to unlatch the speaker from the mounting plate while lifting up on the speaker (see figure below). Press to Release Removing the Speaker from the Mounting Plate Figure 17. SM 26 Surface Mount Speaker • Installation... - Page 18 Extron Electronics makes no further warranties either expressed or implied with respect to the product and its quality, performance, merchantability, or fitness for any particular use. In no event will Extron Electronics be liable for direct, indirect, or consequential damages resulting from any defect in this product even if Extron Electronics has been advised of such damage.
Need help?
Do you have a question about the SM 26 and is the answer not in the manual?
Questions and answers