Related Manuals for PDi Persona P14W
Summary of Contents for PDi Persona P14W
- Page 1 ® Persona P14W Arm-Mounted, Healthcare-Grade LCD HDTV Model: PDI-P14W Document Number: PD196-220R5...
-
Page 2: Table Of Contents
Headphone Sound Mode ................................... 1 1 CHANNELS ........................................... 1 2 Signal .......................................... 1 2 Auto Program ........................................ 1 2 Add / Delete Channels .................................... 1 3 Clear Service Level ...................................... 1 3 Copy Service Level ...................................... 1 4 Parental Control ...................................... 1 4 MPAA Rating ........................................ 1 5 Change Password...................................... 1 5 PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1‐800‐628‐9870 FX 937‐743‐5664... - Page 3 Power on ARC Mode .................................... 2 0 Standby Power ...................................... 2 0 OSD LANGUAGE (On‐Screen Display) .............................. 2 1 SOURCES .......................................... 2 1 Power on Source ...................................... 2 1 CLONING .......................................... 2 2 Save Settings to USB .................................... 2 2 Restore Setting to TV .................................... 2 2 Firmware ......................................... 2 2 Limited Warranty ........................................ 2 3 PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1‐800‐628‐9870 FX 937‐743‐5664...
-
Page 4: Important Safety Instructions
Document Number: PD196‐220R5 PDI‐P14W Page 3 of 23 IMPORTANT SAFETY INSTRUCTIONS THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL CODES. READ AND FOLLOW THE SAFETY INSTRUCTIONS BEFORE ATTEMPTING THIS INSTALLATION. receptacles, and the point where it exits from 1. Read these instructions. the apparatus. 2. Keep these instructions. 11. Only use attachments/accessories specified 3. Heed all warnings by the manufacturer. 4. Follow all instructions. 12. Use only with the cart, stand, tripod, bracket 5. DO NOT use this TV near water. TV SHALL or table specified by the manufacturer or sold NOT be exposed to dripping or splashing. No... - Page 5 Document Number: PD196‐220R5 PDI‐P14W Page 4 of 23 CONSIGNES DE SÉCURITÉ IMPORTANTES CETTE INSTALLATION DOIT ÊTRE EFFECTUÉE PAR UN TECHNICIEN QUALIFIÉ ET DOIT ÊTRE CONFORME À TOUS LES CODES LOCAUX. LIRE ET SUIVRE LES CONSIGNES DE SÉCURITÉ AVANT DE PROCÉDER À L’INSTALLATION. 1. Lire ces instructions. 11. Accessoires Utiliser uniquement 2. Conserver ces instructions. attaches/accessoires recommandés 3. Respecter tous les avertissements.
-
Page 6: Copyright, Disclaimer, And Trademarks
Dolby and the double‐D symbol are trademarks of Dolby Laboratories. All other brand names and product names used in this manual are trademarks, registered trademarks, or trade names of their respective holder. PDi is a registered trademarks of PDi Communication Systems, Inc., Springboro, Ohio. Underwriters Laboratories This device is safety tested and listed by the... -
Page 7: Installing Television
Document Number: PD196‐220R5 PDI‐P14W Page 6 of 23 INSTALLING TELEVISION Installation Precautions 1. Use only a power source from a CSA Certified / UL Approved Class 2 Power Supply suitable for use in a Health Care Facility. This TV will operate on either DC or AC voltage, range 18 to 32 volts. 2. Arm Recoil Hazard: The safety brake pin must remain in the SAFETY BRAKE PIN HOLE whenever the television is removed from the arm or when the arm is removed from the wall bracket to prevent the arm from springing open. Coax Cable Specifications When using a central power supply, cable selection is crucial. Due to long coax cable runs encountered in hospital installations, coax cable employing a solid copper center conductor and copper shield is required. Cable run lengths MUST NOT exceed 150 feet. Required coaxial cable numbers include Alpha 9804C (non‐plenum), Belden 9248 (non‐Plenum), West Penn 806 (non‐Plenum), or West Penn 25806 (Plenum), which have been tested with coax‐powered TVs. Arm Mounting This television is designed to attach to a wall mounted suspension arm adjusted to support a television weighing seven pounds. The single coaxial cable on top of the TV is used to supply low voltage AC or DC power (28VAC or 24VDC) and the RF signal to the television. Note: Contact PDi for additional information on arm compatibility and cable requirements. DIRECT ENTRY KEYPAD You can use the glass keypad to choose power, source, channel, volume, and guide. The navigational arrows used in EPG mode will guide you to your choice. 1. Channel Number Direct entry of desired channel 2. Headphone Plug for listening to device 3. Volume (+) (‐) Increase or decrease sound 4. Mute Silence the audio 5. Closed Caption Allows the display of Closed Caption 6. - Page 8 Document Number: PD196‐220R5 PDI‐P14W Page 7 of 23 Source Choose desired function of the device by touching the Source Icon on the keypad until the desired source is displayed: TV, Auxiliary inputs, Android, or USB Media. TV Mode See Programming Menus and Setup instructions on following page. Channel Entry To directly enter the desired channel, touch channel numbers and Enter . The directional arrow up functions as the dash for channel entry. Choosing Enter again will give you the channel information such as: Channel number Title Resolution Signal standard that is used (NTSC, QAM, ATSC) Guide Touching the Guide icon will access: ...
-
Page 9: Programming Menus And Setup
Document Number: PD196‐220R5 PDI‐P14W Page 8 of 23 SETUP PROGRAMMING MENUS AND Note: A programming remote control is required to perform all setup operations for the television. The programming remote (Part Number PD108‐420) is NOT packaged with the TV and must be ordered separately. The following instructions assume you have a programming remote, have correctly mounted the TV, and connected a coax cable that provides both power and RF signal. SERVICE LEVEL This TV offers a disable and three different programmable Service Levels: Free, Basic, and Premium. Only one Service Level is usable at a time. Disabled is like a mechanical key lock – when in Disabled service level, the TV can be turned OFF and ON, but cannot be used for viewing. A standard message appears on a black screen. Free lets patients watch hospital education and information channels without renting the TV. The channels containing programming for no charge are typically programmed into this level of service. This is the factory default setting for service level. Basic service typically allows additional channels beyond those offered in the FREE level. Premium is the highest Service Level with typically the most channels available for viewing. 1. Press the SETUP button to display the SETUP MODE menu. 2. Press the VOL► to disable or select desired service level. (Free, Basic, Premium) PICTURE Adjustment of picture Brightness, Contrast, Color, Tint, Color Temperature and Sharpness is available to customize the levels you prefer using the on‐screen menus. Brightness, Contrast, Color, Tint, and Sharpness These settings have a range of 1‐100. To change one of them, simply change the number by following this process. 1. Press the SETUP button to display the SETUP MODE menu. 2. Select the Picture menu item. 3. Press the CH▲ / CH▼ buttons to highlight the desired picture item – Brightness, Contrast, Color, Color Temperature, Sharpness, and Noise Reduction. -
Page 10: Color Temperature
Document Number: PD196‐220R5 PDI‐P14W Page 9 of 23 Color Temperature The color temperature menu adjusts the color balance of the picture. “Standard”, “Reddish”, “Greenish”, “Bluish” color temperatures are available for selection; however the individual colors are not adjustable. The “USER” setting allows individual adjustment of each of the TV’s primary colors. The color temperature setting is best set using a calibrated signal source capable of generating a test signal containing both pure white and pure black picture components. 1. Enter the Picture menu 2. Press CH▲ / CH▼ to highlight Color Temperature. 3. Press VOL► to enter it. 4. Press CH▲ / CH▼ to see the individual settings. 5. On User, press VOL◄ / VOL► to highlight R,G, or B or to get out of the customized adjustments. 6. Press CH▲ / CH▼ to adjust R,G, or B NOTE: When you select one of the three colors to adjust, the other two will turn grey. 7. Press SETUP to return to the previous menu. To exit, press SETUP until the programming menus disappear. Noise Reduction Additional picture improvement may be achieved by enabling the Noise Reduction function found in the Picture menu. 1. Press the SETUP button to display the SETUP MODE menu. 2. Select the Picture menu item. 3. Press the CH▲ / CH▼ buttons to highlight the Noise Reduction. 4. Use the VOL◄ / VOL► buttons to alternate, Enable or Disable. -
Page 11: Maximum Volume
Document Number: PD196‐220R5 PDI‐P14W Page 10 of 23 Maximum Volume Sets the maximum volume level the TV can reach. 1. In Sound menu, press the CH▲ / CH▼ button to select Maximum Volume. 2. Press the VOL◄ / VOL► button to determine your preferred maximum volume allowed. 3. Press the SETUP button to return to the preceding menu. Power on Volume Sets the initial volume for the TV upon powering on. Once the TV is on, the volume can be set to any allowable level. If “Power on Volume” is set to LAST, and physical power is NOTE: removed, the TV will power on with a volume of zero. 1. In Sound menu, press the CH▲ / CH▼ button to select Power on Volume. 2. Press the VOL◄ / VOL► button to determine your preferred volume when the TV turns on. Setting the level to LAST causes the TV to remember the last volume level used by the TV prior to turning off. 3. Press the SETUP button to return to the preceding menu. Internal Speaker Enable The speaker’s inside the TV’s cabinet can be turned on or off for each TV Service Level. Note: Sound to the earphone jack remains on at all times. 1. In the Sound menu, press CH▲ / CH▼ button to select the Internal Speaker Enable menu item. 2. Press VOL◄ / VOL► to enter the menu. 3. Press the CH▲ / CH▼ button to select the desired Service Level. 4. Press VOL◄ / VOL► to select Disable or Enabled. -
Page 12: Hdmi Audio Ports
Document Number: PD196‐220R5 PDI‐P14W Page 11 of 23 HDMI Audio Ports The HDMI1 Audio Port and HDMI2 Audio Port have two settings: HDMI and PC‐ANALOG/Component. A device connected to the HDMI ports can receive audio from one of these sources. 1. In the Sound menu, press CH▲ / CH▼ to highlight HDMI 1 or HDMI 2. 2. Press VOL◄ / VOL► to choose between HDMI and PC‐ANALOG/Component. 3. Press SETUP to return to previous menu. Composite Sound Mode The settings are L+R, L+L, and R+R 1. In the Sound menu, press CH▲ / CH▼ to highlight Composite Sound Mode. 2. Press VOL ◄ / VOL ► to choose between settings. 3. Press SETUP to return to previous menu. Headphone Sound Mode The earphone jack sound can be used with either a mono (single ear) or stereo (dual ear) style. 1. In the Sound menu, press CH▲ / CH▼ to highlight Headphone Sound Mode. 2. Press VOL ◄ / VOL ► to choose between settings. 3. Press SETUP to return to previous menu. PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1‐800‐628‐9870 FX 937‐743‐5664... -
Page 13: Channels
Document Number: PD196‐220R5 PDI‐P14W Page 12 of 23 CHANNELS The Channels menu allows you to program different signal sources to either disable or select from three Service Levels (Free, Basic, or Premium) and to add or delete individual channels. It also allows you to block channels, TV programs, movies, and auxiliary sources that can be input to the TV. Each Service Level contains a different channel map. Signal 1. Press the SETUP button on the remote control. 2. Press CH▲ or CH▼ to highlight Channels. 3. Press VOL► to enter the Channels sub‐menu. 4. Four different tuning types are available depending upon the healthcare facility’s signal type. Selection of the correct signal type is required for the TV to recognize all possible channels and before any channel programming can begin. 5. Enter the Channels menu 6. Press CH▲ or CH▼ to highlight Signal. 7. Press VOL ► to select Air, Cable STD, Cable IRC, or Cable HRC. 8. NOTE: Most hospitals use the Cable STD signal style. Auto Program The TV automatically scans each available channel for activity. Channels that display activity are memorized into the selected Service Level. 1. From the Channels menu, select Auto Program 2. In the Auto Program menu, press the VOL► button to select Mode. 3. Press VOL► to set the scope of channel scanning. Analog Only: TV searches for analog channels only. Digital Only: TV searches for digital channels only. Analog and Digital: TV searches for both analog and digital channels. 4. Press the CH▼ button to select the Channel Sequence menu item. -
Page 14: Add / Delete Channels
Document Number: PD196‐220R5 PDI‐P14W Page 13 of 23 Add / Delete Channels Individual analog TV channels that are missing can be manually added to a Service Level. Or, analog TV channels that require deletion can be manually removed from a Service Level. Digital channels found during Auto Programming can be enabled or disabled in each service level. 1. From the Channels menu, press the CH▲ / CH▼ to select Add/Delete Channels. Press VOL◄ / VOL► to select. 2. Press CH▲ / CH▼ to select the service level you wish to add or delete channels. 3. Press VOL◄ / VOL► to enter the Add/Delete Channels menu for that service level. 4. Press CH▲ / CH▼ to select Analog Channel 5. Press VOL◄ / VOL► to scroll through every available channel. The channel number changes to indicate the current channel viewed. 6. Press CH▲ / CH▼ to select Add/Delete Analog Channel. 7. Press VOL◄ / VOL► to alternately Add or Delete the current Analog Channel from the Service Level. 8. Press CH▲ / CH▼ to select Enable/Disable Digital Channel. 9. A listing of all digital channels found during Auto Programming will be displayed. NOTE: If the Enable/Disable Digital Channels states “no Channels”, either the TV did not locate any channels during Auto Programming or the Mode was set to “Analog Only” during Auto Programming. 10. Press CH▲ / CH▼ to select a Digital Channel. 11. Press VOL◄ / VOL► to alternately Enable or Disable the current Digital Chanel from the Service Level. 12. Press SETUP to return to the previous menus. Clear Service Level This empties a service level of all its programmed channels, leaving it blank. 1. From the Channels menu, press the CH▲ / CH▼ to highlight Clear Service Level. -
Page 15: Copy Service Level
Document Number: PD196‐220R5 PDI‐P14W Page 14 of 23 Copy Service Level This copies one service level’s channels to another. 1. In the Channels menu, Press CH▲ / CH▼ to highlight Copy Service Level. 2. Press VOL► to select. 3. Press CH▲ to set the From Service Level. Press CH▼ to set the Service Level. 4. Press VOL ►to copy the Service Level. 5. A confirmation screen will appear. Press CH▲ to proceed. Press CH▼ or SETUP to return to the previous menu. NOTE: After a Service Level is copied, the TV returns to the Copy Service Level menu. If the To Service Level has been set to active in the Service Level setting (see Service Levels on page 4), TV programming will appear. 6. Press SETUP to return to the previous menu. To exit, press SETUP until the programming menus disappear. Parental Control Parental Control allows you to block channels, TV shows, movies, and devices that are connected to the P14W. 1. In the Channels menu, Press CH▲ / CH▼ to highlight Parental Control. 2. From the Parental Control menu, press VOL► to enter the TV Rating menu. 3. Press CH▼ to move to one of the six age‐based categories. 4. Press VOL◄ or VOL► to cycle through the sub‐ratings (ALL, FV, V, S, L or D) or exit out of the sub‐categories in that category. (See page 14 for rating guides) NOTE: The U or B (unblocked or blocked) will turn red when it is highlighted. 5. Press CH▲ or CH▼ to change the sub‐rating. -
Page 16: Mpaa Rating
Document Number: PD196‐220R5 PDI‐P14W Page 15 of 23 NOTE: Categories that are rated for older audiences will be automatically blocked. If you block TV‐Y category, then TV‐Y7 will be blocked automatically. Similarly, if you block TV‐G category, then TV‐PG, TV‐14 and TV‐MA will also be blocked. MPAA Rating Most televised movies are now rated. MPAA Rating selectively allows the TV to only present movie content that is unblocked per its preset level. 1. From the Parental Control menu, enter the MPAA Rating menu. 2. Press CH ▲ or CH ▼ to highlight a particular MPAA Rating. 3. Press VOL ◄ or VOL ► to select Blocked or Unblocked. NOTE: Parental Control will automatically block any category that is rated for older audiences. For example, if you block the PG‐13 category, then R, NC‐17 and X will be automatically blocked also. 4. Press SETUP to return to the previous menu. To exit, press SETUP until the programming menus disappear. Change Password The Parental Control access password can be changed using this menu. NOTE: The factory default password that is programmed into the TV is 0000. PDi Communication Systems, Inc. 40 Greenwood Lane Springboro, Ohio 45066 USA PH 1‐800‐628‐9870 FX 937‐743‐5664... -
Page 17: Television Rating Guides
Document Number: PD196‐220R5 PDI‐P14W Page 16 of 23 Television Rating Guides Guide Meaning TV‐Y Young Children Content not offensive to most viewers TV‐Y7 Children 7 and over Considered suitable for children over 7, may contain Fantasy Violence Scenes TV‐G General Audience Considered suitable for all audiences; children may watch unattended TV‐PG Parental Guidance Suggested Unsuitable for younger children, may contain; Suggestive Dialog, Bad Language, Sex, and Violence Scenes TV‐14 Parents Strongly Unsuitable for children under 14, may contain; Strong Cautioned Dialog, Bad Language, Sex, and Violence Scenes. TV‐MA Mature Audience Only Adults only, may contain; Strong Dialog, Bad Language, Sex, and Violence Scenes Grade Meaning Fantasy Violence Violence Sexual Situation Adult Language Sexual Suggestive Dialog Grade Meaning General Audiences... -
Page 18: Parental Lock Duration
Document Number: PD196‐220R5 PDI‐P14W Page 17 of 23 Parental Lock Duration This sets how long an enabled Parental Lock will be active. 1. In the Parental Control menu, press CH ▲ or CH ▼ to highlight Parental Lock Duration. 2. Press VOL ◄ or VOL ► to select the desired number of hours (1‐99) or Always. 3. Press the SETUP button to return to the previous menu. To exit, press SETUP until the programming menus disappear. Parental Lock This enables or disables the settings in the Parental Control menu. Enabling it will require the password to be entered to access the Parental Control menu in the future. 1. In the Parental Control menu, press CH ▲ or CH ▼ to highlight Parental Lock. 2. Press VOL ◄ or VOL ► to select Enable or Disable. 3. Press the SETUP button to return to the previous menu. To exit, press SETUP until the programming menus disappear. Power on Channel Displays a certain channel each time the TV is turned on. This feature is useful for hospitals that have a Welcome Channel and wish to have it displayed upon initial use of the TV. The patient can then tune to any other available channel. 1. Enter the Channels menu 2. Press CH ▲ or CH ▼ to highlight Power on Channel. 3. Press VOL ► to select it. 4. Press CH ▲ or CH ▼ to highlight the desired Service Level (Free, Basic, or Premium). 5. Press VOL ◄ or VOL ► to select one of the channels currently available in the Service Level or Last. NOTE: Last will cause the TV to turn on to the last channel before it was turned off. -
Page 19: Features
Document Number: PD196‐220R5 PDI‐P14W Page 18 of 23 FEATURES The Features menu provides adjustable settings that customize the TV to your hospital. 1. Press the SETUP button. 2. Press CH▲ or CH▼ to highlight Features. 3. Press VOL► to enter the Features sub‐menu. Power on Caption Mode Power on Caption Mode memorizes the caption setting upon powering the TV off. With this feature set to off, the TV will always power on with the captions disabled. With this feature set to Last, the TV turns on with the last caption setting enabled. 1. Enter the Features menu 2. Press CH▲ or CH▼ to highlight Power on Caption Mode. 3. Press VOL◄ or VOL► to select Last or Off. 4. Press the SETUP button to return to the previous menu. To exit, press SETUP until the programming menus disappear. Auto Power On/Lock The TV will turn on and stay on whenever electrical power is applied to the set. The feature is useful for controlling the TV from a wall switch or preventing the TV from being turned off by the TV power button or the remote control. 1. Enter the Features menu 2. Press CH▲ or CH▼ to highlight Auto Power On. 3. Press VOL◄ or VOL► to select Disabled or Enabled. 4. Press the SETUP button to return to the previous menu. Inactive Power Off (h: mm) The TV will automatically power off after a specific period of viewer inactivity providing energy savings. 1. Enter the Features menu 2. -
Page 20: Digital Captions
Document Number: PD196‐220R5 PDI‐P14W Page 19 of 23 Digital Captions Customization of Closed Captions on ATSC/QAM channels. 1. Enter the Features menu 2. Press CH ▲ or CH ▼ to highlight Digital Captions. 3. Press VOL ► to select it. 4. Press CH ▲ or CH ▼ to highlight the attribute you wish to change. 5. Press VOL ► to change it. (See the table below for the settings of each attribute.) 6. Press SETUP to return to the previous menu. To exit, press SETUP until the programming menus disappear. Attribute Settings Font Size Small, Standard, Large, Default Font Style Style0 – Style 7, Default Foreground Color White, Black, Red, Green, Blue, Yellow, Magenta, Cyan, Default Background Color White, Black, Red, Green, Blue, Yellow, Magenta, Cyan, Default Edge Color White, Black, Red, Green, Blue, Yellow, Magenta, Cyan, Default Foreground Opacity Solid, Translucent, Transparent, Flashing, Default Background Opacity Solid, Translucent, Transparent, Flashing, Default Edge Style None, Raised, Depressed, Uniform, Left Drop Shadow, Right Drop Shadow, Default Digital Mode Time Setup The current time will be set automatically from a digital channel signal provided by a broadcasting TV station. -
Page 21: Diagnostics
Document Number: PD196‐220R5 PDI‐P14W Page 20 of 23 Diagnostics This menu provides readouts of the TV’s internal operation. The Diagnostics menu items are read‐only and cannot be changed. 1. Enter the Features menu 2. Press CH▲ or CH▼ to highlight Diagnostics. 3. Press VOL ► to select it. 4. Press the SETUP button to return to the previous menu. To exit, press SETUP until the programming menus disappear. Field ON Hours: Cumulative time TV is actually on. Field Powered Hours: Cumulative time TV is powered. Firmware VSN 0.64 Micom VSN 0.4 Power On Cause Normal Channel up Power Off This feature causes the TV to turn off once it reaches the highest numbered (last) channel and is usually used with single button style pillow speakers. When the feature is disabled, the TV will continue on to the lowest channel and not turn off. 1. Enter the Features menu 2. Press CH▲ or CH▼ to highlight Channel Up Power Off. 3. Press VOL ◄ or VOL ► to select Enabled or Disabled. 4. Press SETUP to return to the previous menu. To exit, press SETUP until the programming menus disappear. Channel to Other Source External signal sources connected to the TV, such as DVD players or video‐game systems, are shown in the current... -
Page 22: Osd Language (On-Screen Display)
Document Number: PD196‐220R5 PDI‐P14W Page 21 of 23 OSD LANGUAGE (On‐Screen Display) You can select the language you wish to use in your on‐screen displays.. 1. Press SETUP. 2. Press CH▲ or CH▼ to select the OSD Language menu. 3. Press VOL ◄ or VOL ► to select your desired language. 4. Press SETUP to return to the previous menu. To exit, press SETUP until the programming menus disappear. SOURCES The TV’s signal sources can be individually Enabled or Disabled. The available sources in this menu correspond with the components you have connected to the TV’s connectors. NOTE: Please disable all of the TV’s sources that are not to be used. A TV that is switched to a non‐connected source generates nuisance hospital maintenance calls of TV Not Working, when in fact the TV does work, but has been set to an inactive source 1. From the SETUP menu, press CH▲ or CH▼ to highlight Source. 2. Press VOL ◄ or VOL ► to select it. 3. Press CH▲ or CH▼ to highlight a desired source. 4. Press VOL ◄ or VOL ► to change the source status to either Disabled or Enabled/APO (Auto Power Off). NOTE: Sources that are grayed out are not installed in the TV. Enabled/APO means the TV will turn off if there is no video. 5. Press SETUP to return to the previous menu. To exit, press SETUP until the programming menus disappear. Power on Source The TV can be preset to power on to a selected source. 1. Enter the Sources menu 2. Press CH▲ or CH▼ highlight Sources. -
Page 23: Cloning
Document Number: PD196‐220R5 PDI‐P14W Page 22 of 23 CLONING Cloning allows quick programming of a TV from a USB Flash Drive. The operation involves first downloading setup information from a programmed host TV to an USB Flash Drive and then uploading the setup information to another TV. Cloning can also be used to re‐program a programmed TV. Save Settings to USB 1. Turn on the TV 2. Insert a blank USB thumb drive into the cloning port. A Cloning Main Menu will appear on the TV screen. 3. Press CH▲ or CH ▼ to highlight Save Settings to USB. 4. Press VOL► to display the Save Settings to USB menu. Restore Setting to TV 1. Press SETUP on the programming remote, PD108‐420. 2. From the SETUP menu, press CH ▲ or CH ▼ to highlight Cloning. 3. Press VOL ► to select it. 4. Cloning menu will appear 5. Follow prompts on Cloning menu. Cloning Main Menu will appear after approximately 15 seconds. 6. Press CH ▲ or CH ▼ to highlight Restore Settings to TV. 7. Press VOL ► to display a list of previously stored TV setups on the USB Disk. 8. Press CH ▲ or CH ▼ to highlight the file for the P14. 9. Press VOL ► to select it. (The TV will shut off and turn back on automatically; this takes about 15 seconds). 10. Press VOL ► to restore the settings to the TV. (Screen will turn black and LCD light will flash red during this process. Once process is complete LED light will change... -
Page 24: Limited Warranty
Page 23 of 23 Limited Warranty PDi Communication Systems Inc., (“PDi”) warrants, to the original purchaser only, that the product will be free from defects in materials and workmanship, under normal use, for 2 years from the date of original purchase. This warranty does not cover any other equipment that may have been included with PDi’s shipment of this product. After receipt of written notice of a defect or malfunction occurring during the warranty period, PDi will repair or replace goods returned to its Springboro, Ohio location, at its discretion, the whole or any component part of any product manufactured by PDi and found by PDi to be defective. If the decision is made to replace the product, PDi will exchange the model for the same model or a model similar in form and function. As a condition to obtaining warranty service, written notification of the defective product must be received by PDi within ten (10) days of noticing the defect. Repair of said product requires it to be shipped to the PDi factory in Springboro, Ohio. All shipments shall be F.O.B. Springboro, Ohio, and all shipping and freight charges to PDi’s factory shall be paid by the customer. For information regarding authorized servicing and all other information pertaining to this warranty, please contact PDi COMMUNICATION SYSTEMS at 40 Greenwood Lane, Springboro, Ohio 45066 or phone 800‐628‐9870 and ask for Service. This warranty gives specific legal rights and you may also have other rights which vary from state to state. Exclusions from Warranty Products damaged by any catastrophe, accident, or from neglect, misuse, fault, improper assembly, improper maintenance, inadequate return packaging, or negligence by the customer or any third party. They will be treated as out of warranty for external cause to the Products, such as, but not limited to, failure of or faulty electric power, air conditioning, operator error, failure or malfunction of any data communications system. Such conditions will be determined by PDi at its sole unfettered discretion. Service and repair of accessories, apparatus, attachments or any other devices which are not PDi products or options. ...
Need help?
Do you have a question about the Persona P14W and is the answer not in the manual?
Questions and answers
We have a Persona P14W that we had gotten waaaay back when we purchased our original units. We were going to use this one to replace the old one and when we go to program the channels, it only gives us a USB option. Is there a way to get it to revert back to the way we are used to programming channels? Or how do we get it to program the channels? Thank you, Jason