Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for XPS Concrete Genie
- Page 1 • • C O N C R E T E G E N I E F L O O R • G R I N D I N G • M A C H I N E 3 I N 1 •...
- Page 3 This book has important information for use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Concrete Genie could result in injury to you or other personnel, Damage to the machine or to other property could occur as well.
- Page 4 Manual - Concrete Genie DANGER MEAN S: Severe bodily or death can occur to you or other personnel if the DANGER statements found on this machine or in this Owner’s Manual are ignored or are not adhered to. Read and observe all DANGER statements found in this Owner’s Manual and on your machine.
- Page 5 Manual - Concrete Genie Function Code Form Parameter Description Function, Scope Original Data Setting Data Keyboard Control E-01 Control Terminal Control RS485 COM Port Control Frequency Keyboard Number Setting given Keyboard Potentiometer E-02 selection Voltage signal or terminal VS1 E-13 Speedup Time 0.1-6500.0 second...
- Page 6 Manual - Concrete Genie Inverter B type Fault Code Fault Type Possible Fault Reason Troubleshooting Acceleration time is set too short Lengthen acceleration time Frequency inverter output phase of Check the peripheral device, reset after grounding short circuit troubleshooting. S.C.
- Page 7 LEED Compliant Coverage: 400-600 square feet per gallon of working solution. *Up-graded ~ XPS Magnetic Plates Installed Attaching Grinding & Polishing Tools to Genie Magnetic Plates Round Metals & Traps easily snap in place and stay locked due to magnets To remove use a thin blade flat screwdriver place in slot between segment and plate and push outward.
- Page 8 Manual - Concrete Genie Parameter Input Resetting Unlock Press PRG, NO. 00000 showing , then press SET, change the number to 12345 (from left to right), then press SET again, PO will show on screen. Restore Factory Settings Press SET, P0.00 showing, change it to P0.17, press SET, change the number to 1, then press SET, P0.00 should show on the screen.
- Page 9 Manual - Concrete Genie Recessed indicator lights RPM & FAULT display Reset button Computer digital display * Note *Computer pre-set at factory If computer error is indicated on ( do not re-program ) panel, press reset button only! This resets computer to original setting...
- Page 10 Metal Bond Metal Bond Diamond Traps Diamonds - 6 seg Diamonds - 8 seg Diamonds - 10 seg Do Not accept imitations: Use only genuine XPS MAGNETIC PLATES Electrical Diagram Electrical Diagram 2T-1 Electrical Diagram 2T-2/2T-3/3T-420/3T-530/4P12T-40 Connection Sketch GREEN GREEN...
- Page 11 Manual - Concrete Genie Adjust the handle position (for 2T series) Pull handle adjuster as picture (8), adjust handle to suitable position and release handle adjuster, the handle will be locked up as picture (9) Grip handle to operate machine...
- Page 12 Manual - Concrete Genie Troubleshooting MACHINE INSTRUCTION The Genie Series are floor maintaining machines that can be used for grinding, polishing, buffing and stripping. The machines can be used on concrete, terrazzo, marble, granite, wood or vinyl floors. With the suitable pad, the machines can be used to remove epoxy on the floor.
- Page 13 Manual - Concrete Genie Err 1 Open-phase Open-phase in frequency inverter three phase Check three phase input power and three at input side input power phase phase input power wiring Err 2 Output Frequency inverter has device grounding short Check peripheral device, grounding line,...
- Page 14 • • A N A M E R I C A N G R I N D E R C O M PA N Y www.xtremepolishingsystems.com ( 8 6 6 ) 8 1 2 -9 3 1 9 info@xtremepolishingsystems.com w ww . y ou t u b e.c om /us er/Xtre m ePol ishing 2 2 0 0 N W 3 2 n d S t .
Need help?
Do you have a question about the Concrete Genie and is the answer not in the manual?
Questions and answers