Section 13 - Radiance Pro Direct Commands; Miscellaneous Direct Commands; Output Resolution Direct Commands; Menu Shortcuts - Lumagen Radiance Pro Owner's Manual

Section 13 – Direct Commands
Section 13 – Radiance Pro Direct Commands
For rarely used commands, or commands that are not in the Menu system yet, here are some Direct
Commands that can speed configuration. Direct Commands are entered using the Lumagen remote control
or RS232 interface. Make sure to do a Save after any changes.
M iscellaneous Direct Com m ands
MENU 0727 Erase Configuration Memory: In Service Mode enter command, answer question, remove
power. More aggressive than Factory Reset. No Save needed. Cannot be undone.
MENU 0811 Set current input to report HDCP 1.X back to sources
MENU 0819 Set all inputs/memories to report HDCP 1.X back to sources
MENU 0821 Set current input to report HDCP 2.2 back to sources
MENU 0827 Set output aspect to 2.35 (no Anamorphic-lens). This command implements all steps of
the "Fixed 2.35 Output Aspect" section of Tech Tip 16
MENU 0829 Set all inputs/memories to report HDCP 2.2 back to sources
MENU 0860
Globally turn Darbee processing off
MENU 0861 Globally turn Darbee processing on
MENU 0871 Set output as 4k24, 4k25, 1080p50, 1080p60 based on input rate
MENU 0872
Set output as 4k24, 4k25, 4k50, 4k60 based on input rate
MENU 0875
Set HDMI output format as 4:2:2 on all styles (as appropriate)
MENU 0910 Temporary Service Mode (see
MENU 0927 Disable/Enable the "Show Info Page on RS232 <cr> (carriage return) character
MENU 0940
Reinterlacing off
MENU 0941
Reinterlacing on
MENU 0943 Report all HDMI audio modes in EDID back to sources (feature toggle)
MENU 0944 Report basic HDMI audio modes (2-Ch PCM and DD 5.1) back to sources (feature toggle)
MENU 0995 Disable IR commands. Repeat to re-enable IR commands (this is the only IR command
accepted when IR commands are disabled). This command cannot be Saved
MENU 0999 Load Factory Settings (temporary Factory Reset unless Saved)
ALT PREV
Restart the Radiance Pro outputs. Use if TV/Projector has trouble locking on the signal
Output Resolution Direct Com m ands
The following output mode commands are intended for temporary testing only and affect only the current
input, input memory and input resolution. Use the Output Setup Menu to program the output mode, or
modes, if the "Auto" setting is not being used (or use MENU 0871 or MENU 0872 above).
480p: MENU 021
720p: MENU 024
1080i: MENU 028
1080p24: MENU 020
1080p: MENU 027
4k24: MENU 023
MENU 025
4k50:
MENU 029
4k60:
M enu Shortcuts
See Radiance Tech Tip 13 "Direct Commands and Menu Shortcuts" which contains a list of
commands. This Tech Tip is available for download at http://www.lumagen.com.
I R Com m and List
See Radiance Tech Tip 12 "IR Command Interface" which contains a complete list of IR commands.
This Tech Tip is available for download at http://www.lumagen.com.
RS-232 ASCI I Com m and List
See Radiance Tech Tip 11 "RS232 Command Interface" which contains a complete list of RS232
commands. This Tech Tip is available for download at http://www.lumagen.com.
Copyright 2007-2017 Lumagen, Inc
Other
menu which also has Permanent Service Mode)
Progressive with 480 active scanlines
Progressive with 720 active scanlines
Interlaced with 1080 active scanlines
Progressive with 1080 active scanlines
Progressive with 1080 active scanlines
Progressive with 2160 active scanlines
Progressive with 2160 active scanlines
Progressive with 2160 active scanlines
37 Radiance Pro, Rev 052517