Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Eckman EKETC6
Summary of Contents for Eckman EKETC6
- Page 1 Hand Push Lawn Mower, Lawn Scarifier & Lawn Aerator (With Optional Roller) Model EKETC6 Instruction Manual PLEASE READ AND SAVE THESE INSTRUCTIONS FOR FURTHER REFERENCE! ANY QUESTIONS OR PROBLEMS?-Call the ECKMAN Helpline on: 0844 441 3011 or go to www.ECKMAN.co.uk...
-
Page 2: Table Of Contents
Contents I. Parts List .................. II. Specification ..............III. Assembly Instructions ............IV. Safety Guidelines ............V. Height Adjustments............VI. Mower Blade Calibration Adjustments....10 VII. Changing Accessory Cassettes ........11-12 VIII. Guarantee..............Exploded View & Parts List..........13-14... -
Page 3: Parts List
I. Parts List QUANTITY PART NO. NAME (PCS) Mower cassette Aerator cassette Scarifier cassette Foam padded top handle Bar A Lower handle Bolt 35mm Handle connection knob Collection bag Bag attachment strap Roller spacer tubes Roller Bolt 25mm Bolt 15mm 4.Foam padded top handle... -
Page 4: Specification
12. Roller 11.Roller spacer tubes BEFORE ASSEMBLY Firstly unpack and check all parts have been supplied. If you think any parts are missing, first check the packaging again before calling the Eckman helpline on 0844 441 3011 II. Specifications Product Name: GRASSHOPPER(3-in-1 Mower/Aerator / Scarifier , With Optional... - Page 5 Step 3 Attach handle bottom bars to mower by locating the holes at the end of each bottom bar over the lugs on the mower body. The bottom bars are sprung so this works best if you first fit one side then push the opposite bottom bar inwards and into place. Bottom Handle Locating Lugs （The bag and frame are supplied pre-assembled per illustrations Step 4 Bag Assembly...
- Page 6 catcher, attach both sides of the support to the metal bar that’s located Step 5 To attach the grass at the bottom of the mower by the height adjustment levers (see picture below). Clip the strap to the hook at the rear of the catcher, loop the strap over the bottom bar of the handle and push through..
- Page 7 Step 2 Remove the wheels. Step 3 Attach roller. a. attach roller spacer tubes to the both sides of roller. b. line up the two holes located on metal bar, long bolt for outer hole, short bolt for inner hole. Inner hole Outer hole c.
-
Page 8: Safety Guidelines
d. The roller assembled is completed and ready for operation now . Safety Guidelines · Never allow onlookers to place hands, fingers or feet inside any of the accessories (mower/scarifier/aerator) whilst you are working. ·Take extra care and wear non-slip shoes if using this machine when the grass is wet. ·Do not use the machine whilst barefoot or if wearing sandals. -
Page 9: Height Adjustments
V. Height Adjustments 1）Wheels height adjustments The height of the machine above the ground can be adjusted by moving the height adjustment levers to the required position. To the lowest position, one at a time pull the adjustment levers located next to the smaller wheels and move them to their highest position.To the highest cutting position, move the adjustment levers one at a time to their lowest position . -
Page 10: Mower Blade Calibration Adjustments
VI. Mower Blade Calibration Adjustments The blades on the push mower are all calibrated prior to leaving the factory and generally do not require adjustment .However adjustments may be required only if you notice a rough, uneven cut; the mower is difficult to push, or the mower simply does not cut the grass. -
Page 11: Changing Accessory Cassettes
b).Insert a piece of paper between the cutter bar and the reel blades and carefully turn the reel blades by hand. c).All blades should slice the paper evenly along the entire length of the cutter bar while the reel turns smoothly. -
Page 12: Guarantee
Figure 5 Take off the spring loaded connectors from mower cassette and fit them to aerator cassette or scarifier cassette, then squeeze the connectors inwards and fit to the slots. Ensure that both spring-loaded connectors are fully locked in place before attempting to use the machine. -
Page 13: Exploded View & Parts List
intended, or if the product has been modified in any way. Proof of purchase will be required. Your statutory rights remain unaffected. Exploded view & Parts list...
Need help?
Do you have a question about the EKETC6 and is the answer not in the manual?
Questions and answers