Related Manuals for strapex STB 71
Summary of Contents for strapex STB 71
- Page 1 English Operating instructions STB 71 STB 73 STB 75 Battery-operated hand tool for plastic strapping Patent pending www.strapex-stb.com V 03.17...
- Page 2 These operating instructions are part of the product and therefore should be kept for later use or a future owner. Validity: ● STB 71 from Series no A/17020001 ● STB 73 from Series no B/17020001 ● STB 75 from Series no C/17020001...
-
Page 3: Table Of Contents
Preventive and corrective maintenance Preventive maintenance schedule Cleaning the tool Re-greasing the tool Cleaning/replacing the tension wheel Cleaning/replacing the tooth plate Replacing the knife Tool reset Troubleshooting Technical data EC Declaration of Conformity (copy) V 03.17 3 of 28 STRAPEX STB 71/73/75 ENGLISH... -
Page 4: General Information
The legal prescriptions for disposal of all parts must be observed. ► Chargers and batteries should be sorted for environmentally-friendly recycling. ► Observe notes, warnings and instructions of the battery manufacturer. 4 of 28 V 03.17 ENGLISH STRAPEX STB 71/73/75... -
Page 5: Safety
In operating mode AUTO, also the tensioning or welding button can be pressed again to stop strap tensioning. ● After welding, cut the strap using a suitable tool (strap cutter). V 03.17 5 of 28 STRAPEX STB 71/73/75 ENGLISH... - Page 6 Do not clean the tool with water or steam. When using the tool outdoors, protect it from rain. Use only original spare parts Using non-original spare parts will void the warranty and any liability. 6 of 28 V 03.17 ENGLISH STRAPEX STB 71/73/75...
-
Page 7: General Safety Warnings For Power Tools
Loose clothes, jewellery or long hair can be caught in moving parts. g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. V 03.17 7 of 28 STRAPEX STB 71/73/75 ENGLISH... - Page 8 Liquid ejected from the battery may cause irritation or burns. 2.4.6 Service a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 8 of 28 V 03.17 ENGLISH STRAPEX STB 71/73/75...
-
Page 9: Description
Rocker lever Operating panel Unlock button, battery Battery Type designation Strap guide indicator 10 Serial number (XJJMMYYYY) X A=STB 71, B=STB 73, C=STB75 JJ Year MM Month YYYY consecutive number 11 Welding device 12 Tensioning device Operating panel Keypad "Favourite"... -
Page 10: Function
″, ″) STB 75: 15–16 mm, 18–19 mm ( ″, ″) Scope of delivery For strapping tool STB 71 / STB 73: ● Battery 18 V/2.0 Ah Li-Ion Part no 2187.011 ● Battery charger GAL 1880 CV EU Part no 2188.020 or for USA version: ●... -
Page 11: Accessories
Part no 1821.901.010 ● Offset screwdriver Part no 1821.901.007 Accessories ● Protection plate set Part no 2189.010 ● Protection cover set Part no 2189.011 ● Suspension bow set Part no 2189.012 V 03.17 11 of 28 STRAPEX STB 71/73/75 ENGLISH... -
Page 12: Preparing For Operation And Settings
The charge status is shown in % and by a progress bar (1) – Below 10% minimum charge (battery must be charged) – The information symbols (2) only appear if a corresponding situation is occuring (Section 6.8). 12 of 28 V 03.17 ENGLISH STRAPEX STB 71/73/75... -
Page 13: Setting The Operating Mode
The welding button (Section 3.1) must then be briefly pressed so that the straps are welded and the upper strap is cut off. Recommended for varying (soft, hard) packaged goods. V 03.17 13 of 28 STRAPEX STB 71/73/75 ENGLISH... -
Page 14: Setting Strap Tension
STB 75: Standard: 1300 1700 2100 2500 2900 3300 3700 4100 4500 lbf* 1000 Soft 1000 1150 1300 1450 1600 (rounded values) * N = Newton, lbf = pound-force per square inch 14 of 28 V 03.17 ENGLISH STRAPEX STB 71/73/75... -
Page 15: Setting Soft Tension
The favourite mode (Section 4.7) can be switched on even when the key lock is activated. If the adjustment of the settings is not desired, the favourite level should be set in the same way as the normal level. V 03.17 15 of 28 STRAPEX STB 71/73/75 ENGLISH... -
Page 16: Select Favorite
After approx. five minutes without operation the tool switches to sleep mode. – The operating panel is switched off (black). ► Actuating the rocker lever switches the sleep mode off again. 16 of 28 V 03.17 ENGLISH STRAPEX STB 71/73/75... -
Page 17: Operating Instructions
If the strap is not inserted completely, the strap guide indicator (Section 3.1, item 9) shows a red field. Insert the strap completely. The strap guide indicator is black. ► Remove hands from the straps before tensioning! V 03.17 17 of 28 STRAPEX STB 71/73/75 ENGLISH... - Page 18 ● Welding without strap tension: Press the tensioning button briefly, then press the weld- ing button (Section 3.1, item 2). 18 of 28 V 03.17 ENGLISH STRAPEX STB 71/73/75...
-
Page 19: Checking The Seal
► Strapping with poorly welded seals must be performed again. ► Check strap type (Section 7). ► If good welding is not achieved, the tool must be checked by an authorized service center. V 03.17 19 of 28 STRAPEX STB 71/73/75 ENGLISH... -
Page 20: Setting The Strap Width
″) ● STB 75: 15-16 mm, 18-19 mm ( ″, ″) STB 75 5.3.1 STB 71: Change strap width from 9 mm to 13 mm ( ″ to ″) Required parts Order number Strap guide front 13 mm ( 1832.031.051 ″) - Page 21 ► Fit strap guide rear 13 mm (9) (secure cylinder screw with Loctite 222). ► Fit side cover (5) (secure cylinder screw with Loctite 222). Install strap guide rear 13 mm (8). V 03.17 21 of 28 STRAPEX STB 71/73/75 ENGLISH...
- Page 22 ► Fit strap guide rear 16 mm (9) (secure cylinder screw with Loctite 222). ► Fit side cover (5) (secure cylinder screw with Loctite 222). Install strap guide rear 16 mm (8). 22 of 28 V 03.17 ENGLISH STRAPEX STB 71/73/75...
-
Page 23: Preventive And Corrective Maintenance
STB 75 ► Refit the side cover (4). Cleaning/replacing the tension wheel Required parts Order number STB 71 / STB 73: Tension wheel (1) (wear part) 1821.047.033 STB 75: Tension wheel (1) (wear part) 1821.047.036 Ball bearing, Ø35/47x7 (2) 1930.180.356 Cylinder screw Torx, M4 (4) 1821.027.063... -
Page 24: Cleaning/Replacing The Tooth Plate
► Lightly lubricate the inner teeth of the tension wheel with Klüber grease GBU Y 131 (Microlube). Cleaning/replacing the tooth plate Required parts Order number STB 71 / STB 73: Tooth plate (2) (wear part) 1821.048.026 STB 75: Tooth plate (2) (wear part) 1821.048.030 Torx counter-sunk screw Torx (1) 1832.039.285... -
Page 25: Replacing The Knife
Replacing the knife Required parts Order number STB 71 / STB 73: Knife (1) (wear part) 1821.209.036 STB 75: Knife (1) (wear part) 1821.209.040 Cylinder screw Torx, M4 (3) 1821.027.063 Cylinder screw Torx, M4x12 (5) 1913.904.125 Flanged bushing (6) 1832.022.238 Dismantling ►... -
Page 26: Troubleshooting
In the case of other error numbers not described here, please contact the the local service center. If the error cannot be rectified by applying the measures described above, please contact the local service center! 26 of 28 V 03.17 ENGLISH STRAPEX STB 71/73/75... -
Page 27: Technical Data
Battery 18 V/2.0 Ah, Li-Ion 18 V/2.0 Ah, Li-Ion 18 V/4.0 Ah, Li-Ion BOSCH BOSCH BOSCH * refer to Section 2.3, Vibration exposure Continued on the next page V 03.17 27 of 28 STRAPEX STB 71/73/75 ENGLISH... - Page 28 EEC-Design certification: No. M8A 17 03 28456 006 Place of certification: TÜV SÜD Product Service GmbH Type designations: STB 71, STB 73, STB 75 From machine no./ year of construction: A/17020001, B/17020001, C/17020001 / 2017 CH-8953 Dietikon, 14.02.2017 Orgapack Orgapack...
Need help?
Do you have a question about the STB 71 and is the answer not in the manual?
Questions and answers