Lincat IH21 Installation, Operating And Servicing Instructions
Countertop induction hobs
Hide thumbs
Also See for IH21:
- Installation, operating and servicing instructions (12 pages) ,
- User and installation instructions manual (9 pages) ,
- Installation and maintenance information (6 pages)
Table of Contents
Advertisement
Installation, Operating and Servicing
Instructions
Countertop Induction Hobs
IH21, IH3, IH42
Please make a note of your product details for
future use:
Date Purchased:_________________________
Model Number:__________________________
Serial Number:__________________________
Dealer:_________________________________
_______________________________________
IS 565 ECN 3766
Page 1 of 13
Advertisement
Table of Contents
Related Manuals for Lincat IH21
Summary of Contents for Lincat IH21
- Page 1 Installation, Operating and Servicing Instructions Countertop Induction Hobs IH21, IH3, IH42 Please make a note of your product details for future use: Date Purchased:_________________________ Model Number:__________________________ Serial Number:__________________________ Dealer:_________________________________ _______________________________________ IS 565 ECN 3766 Page 1 of 13...
-
Page 2: Table Of Contents
WARNING! This symbol is used whenever there is a risk of personal injury. CAUTION! This symbol is used whenever there is a risk of damaging your Lincat product. NOTE: This symbol is used to provide additional information, hints and tips. -
Page 3: Warnings And Precautions
WARNINGS AND PRECAUTIONS This appliance must be installed, commissioned and serviced by a qualified person in accordance with national and local regulations in force in the country of installation. If a supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person. -
Page 4: Technical Data
12.0 12.8 IH42 21.5 Power Ratings: Model IH21 Amps Supply IH21 (twin zone) 13.0 230V/1ph/50Hz Heat input rear zone, normal Heat input rear zone, boost 13.0 Heat input front zone, normal Heat input front zone, boost Max total heat input cannot exceed 3kW... -
Page 5: Installation And Commissioning
Supply cords shall be oil resistant, sheathed flexible cable not lighter than ordinary polychloroprene or equivalent elastomer sheathed cord (code 60245 IEC 57) The IH21 and IH3 appliances have a single supply cord. The IH42 appliance has two supply cords. -
Page 6: Operating Instructions
Use pans of the size and type recommended. Operation of the pan detection system is dependent on the size of the pan and its material. Recommended pan base diameters – IH21, IH3, IH42 Single / Rear zone Front zone 180mm 120mm... - Page 7 The pan should be located concentrically over the glass target ring. If the inner ring of the ceramic glass is visible around the pan, the pan is too small. It is normal for induction generators to make buzzing, whistling and clicking noises, especially on lower power settings.
- Page 8 The following symbols are observed through the ceramic glass: Power level setting (1-9) Power boost function Automatic heat up control Control lock function Pan detection (no pan present) Residual heat display Error codes - generator Error – rotary control (lightning symbol) Power level settings 9 power level settings are available.
- Page 9 On the IH3, power boosting raises the coil from 2.4kW to 3kW. On the IH21 and IH42, if a rear coil (2kW) is power boosted, it’s power increases to 3kW and the front coil will be shut down. If a front coil (1kW) is power boosted, it’s power increases to 1.8kW and the rear coil is limited to 1.2kW.
-
Page 10: Cleaning
There are numerous ‘E’ symbol error codes identifying issues within the system which are primarily of use when reporting a fault to the Service Department at Lincat. Some errors can be cleared by turning the control off, or completely turning off and unplugging the appliance before reconnecting, or by allowing the unit to cool down. -
Page 11: Servicing, Maintenance And Component Replacement
SERVICING, MAINTENANCE AND COMPONENT REPLACEMENT Replacement of air filter Cool the appliance and disconnect from supply, the filter is located in the base of the appliance. Raise the latch and lift the filter away from the base. Replace the used filter with a new one and reverse the procedure to re-fit. -
Page 12: Fault Finding
Please refer to the Service Help Desk number on the final page of this manual. SPARE PARTS LIST Part Number Description FE10 Foot FG03 Fanguard Air Filter – IH42 FI36 Air Filter – IH21, IH3 FI41 KN251 Control knob NE43 Neon S/R0181 Cooling fan IS 565 ECN 3766 Page 12 of 13... -
Page 13: Service Information And Guarantee
Type number All available on serial plate Serial number Lincat reserve the right to carry out any work under warranty, given reasonable access to the appliance, during normal working hours, Monday to Friday, 08:30 to 17:00. GUARANTEE This unit carries a comprehensive UK mainland 2 year warranty. The guarantee is in addition to, and does not diminish your statutory or legal rights.
Need help?
Do you have a question about the IH21 and is the answer not in the manual?
Questions and answers