Table of Contents
Advertisement
Fully Automatic Microprocessor Controlled
Battery Charger for 12-Volt Lead Acid Batteries
CAUTION:
Read all Safety Rules carefully, and folllow all Operating Instructions when using this product.
Monitor battery during first hour of operation and check battery during charging
process. If smoke or other signs of excessive heat are detected or if battery emits
a rotten egg smell, your battery is may be critically damaged and charging should
be terminated. Immediately vent the room by opening windows, unplug the battery
charger, allow the charger and the battery to cool down and then properly dispose
of the battery. Do not attempt to charge the damaged battery! Failure to adhere to
this warning may cause serious injury or property damage.
Detroit, Michigan 48202
©2006 GM Corp. All Rights Reserved.
Printed in China
Owner's Manual
WARNING
Model No.: I-7005T
ACDelco, ACDelco Emblem, and the
ACDelco related graphics are General
Motors Trademarks used under
license to MVP(H.K.) Industries Ltd.
Consumer enquiries: 1 887 246 6006
Advertisement
Table of Contents
Related Manuals for ACDelco I-7005T
Summary of Contents for ACDelco I-7005T
- Page 1 Do not attempt to charge the damaged battery! Failure to adhere to this warning may cause serious injury or property damage. ACDelco, ACDelco Emblem, and the ACDelco related graphics are General Motors Trademarks used under Detroit, Michigan 48202 license to MVP(H.K.) Industries Ltd.
-
Page 2: Important Safety
SAVE THESE INSTRUCTIONS PRODUCT DESCRIPTION SAVE THESE INSTRUCTIONS. For your safety, read, understand, and follow the Automatic battery charger is designed to information provided with and on this battery charge 12 Volt, rechargeable lead acid charger. The owner and operator of this batteries with rated Amp Hour (Ah) capacity equipment shall have an understanding of of no less than 16Ah. - Page 3 I-7005T. 7. Do not operate charger if it has received 2. NEVER expose this device to rain, snow, a sharp blow, been dropped, or otherwise fog, or high humidity.
-
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS 11. PERSONAL PRECAUTIONS h) Use charger for charging a LEAD- ACID battery only. Model I-7005T is a) Someone should be in the range of your not intended to supply power to a low voice or close enough to come to your... -
Page 5: Before Use
BEFORE USE A. PREPARING TO CHARGE C. DC CONNECTION PRECAUTIONS 1. If it is necessary to remove battery 1. Connect and disconnect dc output from vehicle to charge, always remove clamps only after setting any charger grounded terminal from battery first. switches to off position and removing AC cord from electrical outlet. -
Page 6: How To Use
HOW TO USE A. Use of the Hook-up for Negative Ground: 5. For negative-grounded vehicle (see Fig, F O L L O W T H E S E S T E P S W H E N 2A), connect POSITIVE (RED) clamp BATTERY IS INSTALLED IN VEHICLE. - Page 7 HOW TO USE B. For use with charging battery removed from vehicle or boat FOLLOW THESE STEPS WHEN BATTERY IS OUTSIDE OF A VEHICLE. A SPARK NEAR THE BATTERY MAY CAUSE BATTERY EXPLOSION. TO REDUCE RISK OF A SPARK NEAR BATTERY: 1.
-
Page 8: Maintenance
MAINTENANCE • Wipe the charger clamps clean after each DANGER use. Use emery paper to remove corrosion from clamps. To reduce the risk of electric shock: • Wipe the charger case with a clean dry cloth • NEVER perform maintenance with after each use. -
Page 9: Operation
OPERATION • ON / OFF key - When AC power cord • Volt./Bat.% key - Press once and the is plugged into the AC outlet, the digital indicator will display a 3 character voltage indicator should display the term ‘OFF’. measurement;... - Page 10 OPERATION • Function Key USE OF REINFORCED ACTIVATION MODE: Maintenance Cycle Mode - Pressing ■ Function Key once will result in a charge Your battery charger contains a Reinforced cycle called a ‘Maintenance Cycle’. This Activation Mode. In certain cases, batteries cycle is also referred to as a ‘Pulse’...
- Page 11 OPERATION • Optimal Charging/remnant Time (CCA) • Remaining charging time is displayed in button - Use this button to select the “X.X” h (number of hours remaining in battery CCA value in order to proceed with the battery charging time) for 5 seconds, optimized charging.
- Page 12 ERROR CODES AND STATUS CODES System Error. Have the Battery Charger inspected and repaired by a qualified technician. Reverse polarity connection; there is a bad connection; or the voltage of the battery is too low. Verify the polarity and connect the Battery Charger accordingly; verify that the clamp is connected properly;...
-
Page 13: Troubleshooting
Display on, charger Power to the display is provided by unplugged battery connection press any key SPECIFICATION 40A charger model : I-7005T 40A max output for 12V type battery Input voltage : 108 to 132 AC/50~60±3 Hz. FUSE : 15A/250V Output voltage... -
Page 14: Statement Of Fcc Compliance
STATEMENT OF FCC COMPLIANCE MADE IN CHINA NOTE: This device has been tested in compliance with Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential/industrial installation. This device can radiate radio frequency energy and may cause harmful interference to radio communications.
Need help?
Do you have a question about the I-7005T and is the answer not in the manual?
Questions and answers