Care & Maintenance; Troubleshooting Guide; Replacement Parts - Ninja BL680A Owner's Manual

Care & Maintenance
HOW TO CLEAN
CAUTION: Make sure that the motor base is
unplugged from the power source before inserting
or removing any blade assembly and before
cleaning.
CAUTION: DO NOT immerse the motor base into
water or any other liquid.
1 Separate/remove all parts from each other.
2 Hand Washing: Wash the lids, pitcher, food processor
bowl, Nutri Ninja cup, and blade assemblies in warm,
®
soapy water. When washing the blade assemblies, use
a dish-washing utensil with a handle to avoid direct
hand contact with blades. Handle blade assemblies
with care to avoid contact with sharp edges. Rinse and
air dry thoroughly.
Dishwasher: The containers, lids, blade assemblies
and attachments are all dishwasher safe. The lids
and blade assemblies are top rack dishwasher safe.
Ensure that the blade assemblies are removed from the
containers before placing in the dishwasher.
WARNING: Handle the Blade Assemblies with
care when washing, as the blades are sharp.
Contact with the blades' edges can result in
laceration.
3 Wipe the motor base clean with a damp cloth.
Please call customer service if any servicing needs to be
performed on the appliance at 1-877-646-5288.
15 1-877-646-5288
HOW TO STORE
|
1 Store the Nutri Ninja Ninja Blender System with
® ®
Auto-iQ ™ Technology upright with the blade assembly
inside the corresponding container with the lid secured
on top. Do not place anything on top. Store the rest of
the attachments in a safe place where they will not be
damaged and won't cause harm. Wrap the power cord
around the cord wrap on the back of the motor base.
RESETTING THE MOTOR THERMOSTAT
|
The Nutri Ninja Ninja Blender System with Auto-iQ
Technology features a unique safety system which
prevents damage to the unit's motor and drive system
should you inadvertently overload your appliance. If
the appliance is being overloaded, the motor
will stop. Allow the appliance to cool for
approximately 15 minutes. To reset the appliance,
follow the resetting procedure below:
1 Unplug the appliance from the electrical outlet.
2 Remove and empty the container and ensure that no
food is jamming the Blade Assembly or attachments.
3 Allow the appliance to cool for approximately 15
minutes.
4 Re-install the container onto the base and re-plug the
appliance into the electrical outlet.
5 Proceed to use the appliance as before making sure not
to exceed the recommended maximum capacities.

Troubleshooting Guide

PROBLEMS
Make sure the container is securely locked on the motor base.
Make sure the lid is securely on the container in the correct position (align
arrows).
The appliance is turned "Off". Press the power button ( ) to turn "On".
Check that the plug is securely inserted into the electrical outlet.
Motor Doesn't Start or Blade
Check the fuse or circuit breaker.
Assembly Doesn't Rotate.
The unit has overloaded. The appliance will stop and the power light will
flash. Unplug and wait approximately 15 minutes before using again.
The unit has overheated. Unplug and wait approximately 15 minutes before
using again.
Check to make sure the unit is not overloaded.
Either you are chopping too much food at one time, or the pieces are not of
Food is Unevenly Chopped.
even size and processing smaller amounts per batch.
Food is Chopped Too Fine or is
The food has been over processed. Use Auto-iQ
Too Watery.
controlled processing.
Food Collects On Lid or On the
The mixture is too thick. Add more liquid.
Sides of the Container.
Do not use ice that has been sitting out or has started to melt. Use ice
You Cannot Achieve Snow
straight from the freezer.
From Solid Ice.
Start with a few pulses and then go to a continuous blending cycle.
Make sure surface and suction feet are wiped clean. Suction feet will only
stick to smooth surfaces. Suction feet WILL NOT stick on some surfaces
Motor Base Won't Stick to
such as, wood, tile and non-polished finishes.
Counter or Table Top.
DO NOT attempt to use appliance when the motor base is stuck to a
surface that is not secure, (cutting board, platter, plates, etc.).
Your Ninja
You get an "Err" Message
to use a program that is not designed for the jar you have installed. The
programs will light up indicating which programs are available for each jar.
The unit is not installed properly. For your safety the unit will only be able to
You have a blinking red light
be turned on when it is properly assembled. Please refer to the assembly
pages of this inspiration guide for assistance.

Replacement Parts

ORDERING REPLACEMENT PARTS
To order additional parts and attachments, please visit our website: www.ninjakitchen.com
or feel free to contact customer service: 1-877-646-5288.
POSSIBLE REASONS & SOLUTIONS
Pulse button for
™
is able to detect which jar is on the base. You may be trying
®
www.ninjakitchen.com 16