Advertisement
Quick Links
Please dispose of packaging for the product in a responsible
manner. It is suitable
environment, take the packaging to the local amenity tip
and place into the appropriate recycling bin.
Never dispose of electrical equipment or batteries in with
your domestic waste. If your supplier offers a disposal facili-
ty please use it or alternatively use a recognised re-cycling
agent. This will allow the recycling of raw materials and help
protect the environment.
FOR HELP OR ADVISE ON THIS PRODUCT PLEASE CONTACT YOUR DISTRIBUTOR,
OR SIP DIRECTLY ON:
TEL: 01509500400
EMAIL: sales@sip-group.com or technical@sip-group.com
www.sip-group.com
Ref: 080812
for recycling.
Help to protect the
24
01943
6"x 10"
Belt Disc Sander
Please read and fully understand the instructions in
this manual before operation. Keep this manual
safe for future reference
1
Advertisement
Related Manuals for SIP 01943
Summary of Contents for SIP 01943
- Page 1 This will allow the recycling of raw materials and help protect the environment. FOR HELP OR ADVISE ON THIS PRODUCT PLEASE CONTACT YOUR DISTRIBUTOR, OR SIP DIRECTLY ON: TEL: 01509500400 EMAIL: sales@sip-group.com or technical@sip-group.com Please read and fully understand the instructions in www.sip-group.com...
-
Page 2: Declaration Of Conformity
LE12 9NH England As the manufacturer's authorised representative within the EC declare that the 6”x 10” Belt / Disc Sander - SIP Pt. No. 01943 Conforms to the requirements of the following directive(s), as indicated. 2006/95/EC Low Voltage Directive 2006/42/EC... -
Page 3: Table Of Contents
NOTES CONTENTS Page No. Description Safety instructions Electrical connections Technical specifications Getting to know your belt disc sander Assembly instructions Operating instructions Care and maintenance Exploded diagram Parts list Declaration on conformity... -
Page 4: Description
SIP recommends that this belt disc sander should not be modified or used for any ap- plication other than that for which it was designed. If you are unsure of its relative ap- plications do not hesitate to contact us and we will be more than happy to advise you. - Page 5 PARTS LIST Continued... SAFETY INSTRUCTIONS….cont Ensure that the belt disc sander is correctly turned off when not in use and store in a Description SIP Part No. safe, dry area, out of reach of children. Screw M6 x 16 WD02-00034 Do not unplug the belt disc sander to switch it off - always use the on/off switch.
-
Page 6: Electrical Connections
WD02-00008 Bolt M6 x 16 WD02-00034 This SIP sander is fitted with a standard 230v ~ 13 amp type plug. Before using the Table frame bracket WD02-00035 heater, inspect the mains lead and plug to ensure that neither are damaged. If any... - Page 7 EXPLODED DIAGRAM ELECTRICAL CONNECTION….cont The wires for the plug are coloured in the following way: Yellow / green Earth Blue Neutral Brown Live As the colours of the wires may not correspond with the markings in your plug, pro- ceed as follows: The wire which is coloured blue, must be connected to the terminal marked with N or coloured black.
-
Page 8: Technical Specifications
Using a 12 mm spanner loosen (do not remove) the four bolts shown in diagram. This SIP belt disc sander is covered by a 24 month parts and labour warranty covering failure due to manufacturers defects. This does not cover failure due to misuse or op- erating the machine outside the scope of this manual. -
Page 9: Getting To Know Your Belt Disc Sander
CARE AND MAINTENANCE GETTING TO KNOW YOUR BELT DISC SANDER ISOLATE THE MACHINE FROM THE MAINS SUPPLY: Slide the belt tensioning lever (item 2 on page 9) to slacken the belt. Unscrew the knurled bolt from the side of the belt table and remove. Unscrew the two black knobs which hold the rear fence on the belt table, and remove. -
Page 10: Assembly Instructions
ASSEMBLY INSTRUCTIONS OPERATING INSTRUCTIONS….cont Leg Stand Parts Below diagrams show the belt sander sanding curved edges, When sanding with the idler drum, use very light pressure. If you press too hard, you'll put an unnecessary strain on the sleeve bearings in the idler drum. Sanding curved edges Undo the 6 mm cap-head bolt and lift the belt sander bed as shown in below diagram, Once in... -
Page 11: Operating Instructions
ASSEMBLY INSTRUCTIONS….cont ASSEMBLY INSTRUCTIONS….cont Leg Stand Assembly Take upright leg (A) x2 and bolt to lower sup- port (length) (B) x1 using the bolts supplied on Lastly fit the fence as shown in the pic- both sides until you have a `H` frame as show ture. - Page 12 ASSEMBLY INSTRUCTIONS….cont ASSEMBLY INSTRUCTIONS….cont Fit the belt disc sander to the leg stand using the 4 bolts, nuts and washers supplied, Below diagram is how your belt disc sander should look like. Locate the angle guide and knob and attach to one side of the sander;...
Need help?
Do you have a question about the 01943 and is the answer not in the manual?
Questions and answers