Dyegoo GT06 User Manual
  1. Manuals
  2. Brands
  3. Dyegoo Manuals
  4. GPS
  5. GT06
  6. User manual

Dyegoo GT06 User Manual

Gps vehicle tracker (gps+gsm+sms/gprs)
Hide thumbs Also See for GT06:

Advertisement

Table of Contents

GPS Vehicle tracker
(GPS+GSM+SMS/GPRS)
GT06 User Manual
(Version 3.2)
Thank you for purchasing the tracker. This manual shows how to operate the
device smoothly and correctly. Make sure to read this manual carefully before
using this product. Please note that specification and information are
subject to changes without prior notice in this manual. Any change will be
integrated in the latest release. The manufacturer assumes no responsibility
for any errors or omissions in this document.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GT06 and is the answer not in the manual?

Questions and answers

Related Manuals for Dyegoo GT06

Summary of Contents for Dyegoo GT06

  • Page 1 GPS Vehicle tracker (GPS+GSM+SMS/GPRS) GT06 User Manual (Version 3.2) Thank you for purchasing the tracker. This manual shows how to operate the device smoothly and correctly. Make sure to read this manual carefully before using this product. Please note that specification and information are subject to changes without prior notice in this manual.
  • Page 2 1. Summary Working Based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any remote targets by SMS or internet. Overview of the characteristics: 1.GSM 850/900/1800/1900MHZ. 2.GPS position. 3.Auto set APN. 4.300Mah Battery inside, Power-Cut alarm. 5.Motion detect, save GPRS flow.
  • Page 3 Power line: Relay: Microphone: SOS line: Manual...
  • Page 4 3. Specs 1）.GSM：850/900/1800/1900MHZ 2）.GPRS: Class12, TCP/IP 3）.Working Voltage：9-50V DC 4）.Working current：≈22mA (12VDC) 5）.Working current：≈12mA (24VDC) 6）.GPS locating time：Cold start≈38s（Open sky） Warm start≈32s Hot start≈2s（Open sky） 7）.GPS Precision：10m（2D RM） 8）.Working temperature：-20℃～+70℃ 9）.Working humidity：20%～80%RH 10）.Measurement：98（L）×52（W）×16.5（H）mm...

  • Page 5: Device Status Indicators

    4. Wire defined 5.Device status indicators 5.1 Connect DC 9-50V power supply and the red LED will light continuously. 5.2 The blue LED light continuously when searching the GPS signals. When GPS position,the blue LED flashing. 5.3 The intermediate green LED (GSM signal state) GSM signal is normal, green LED flashing.

  • Page 6: Prepare For Installation

    Prepare for installation 6.11 Product Check. Open the packing box and check the device‘s model and accessories. If the model is wrong or the accessories not complete, please contact the dealer. 6.12 Choose SIM card. Please insert a SIM card to the device. Please take dealer’s advice as reference.
  • Page 7 receiving side of the device is face up and without metal cover. Note: The metal cover will lessen the receiving of GPS signals.6. The device connecting requirements. 7. Device wiring requirements 7.1 The device power supply is DC 9-50V. The red line is positive pole while the black line is negative pole.

  • Page 8: User Settings

    device will upload the data to the online platform (the default interval of uploading data is 15seconds). When the car is in static state for a long time, the device will be in energy saving mode and it will be more smart and precise.
  • Page 9 oil and power. 4) Only 2 number can be center number. 5) Change center number must resend the command. 6)Add new center number by CETNER,A, and delete by CENTER,D Command Successful Setting：Add admin account 1 OK! Feedback View Center Number Text command Parameter Sample...
  • Page 10 Authorized Number Set Text command Parameter Sample Authorized 101# number # 1：101#13800138000# 102# number # 2：102#12345678912# 103# number # 3：103#12345678912# Authorized D11# D11# D12# D12# D13# D13# Command 1) Authorization number for SMS control oil. Description 2) only three numbers to set the authorization number 3) change the authorization number needs to delete the previous number Add Authorization account 1...

  • Page 11: Apn Setting

    View Authorized Number Text command Parameter Sample View C10# C10# authorized Command This directive is used to view the equipment Description authorization number Command Successful Setting： Authorization 1： Feedback Authorization 2： Authorization 3： 5)APN Setting Text command Parameter Sample APN Setting 802#username#pass 1：802#intenet#123#123#...
  • Page 12 word] 2: 802#internet# APN differs according to the local telecom operators. Command For example：APN request password，please refer to Description Sample 1，and Sample 2 for no password. Command Successful Setting：SET APN OK！ Feedback Server Text command Parameter Sample SERVER 803#SERVER # port# 803#222.217.240.243#8011# Parameter View...
  • Page 13 Feedback 7)Moving Time Interval Text command Parameter Sample TIMEER Parameter 730#uploading interval# 730#20# setting Time scope：0，10~60 seconds； 0,no data uploading； Command 10~60,means time interval ；the default value is 15 Description seconds！ Command Successful Setting：SET TIMER OK！ Feedback 8)Static Time Interval Text command Parameter Sample...
  • Page 14 Timescope：1~60 minutes；The device has Command 3D transmission and the default time interval are 5 Description minutes. Command Successful Setting：SET STATIC TIME OK！ Feedback Cancel the continuous upload Text command Parameter Sample NUP# NUP# This command is used to cancel sending data to the Command platform Description...
  • Page 15 10)Oil-Cut Text command Parameter Sample RELAY 222# 222# cut off oil and power Parameter1 RELAY 333# 333# recover oil and power Parameter2 1)RELAY control the start and closeness of the relay 2) Only the center number can operate. 3 ） the device only cut off the oil circuit on the condition of the driving speed below 20KM/H or in static Command state.

  • Page 16: Vibration Alarm

    Text command Parameter Sample 801#location, 801#E8# time# Command The default time zone is Beijing time. If time zone need Description revised, please operate according to the above command. Command Successful Setting：Set time zone ok! Feedback 12)Vibration Alarm Text command Parameter Sample Open Vibration Alarm 911#...
  • Page 17 Cancel vibration 456# 456# alarm the sensitivity value of the vibration is from 1 to 5，1is the most sensitive and o is close. Command Description Alarming ways: 1, calling 2, texting, 3 calling and texting. Must set the center number and receiving number. Command Feedback set vibration alarm level，OK! 13)Speed Alarm...
  • Page 18 Must set the center number and receiving number. Command Successful Setting：set speeding alarm，OK! Feedback 14)ACC Alarm Text command Parameter Sample Open ACC 840#1# 840#1# Alarm Close ACC 840#0# ALARM The speed scope is form 60-220, if the speed is no this Close ACC cope, the alarm is off.
  • Page 19 15)Reset Text command Parameter Sample RESET 930# 930# Command Reset the device Description Command Successful Setting：Reset system, ok! Feedback 16)Factory Text command Parameter Sample Parameter 940# 940# Restore the factory setting Command Only center number can initial this function Description Factory setting will recover to the original setting Command Successful Setting：FACTORY OK！...

  • Page 20: Language Setting

    Feedback 17)Language Setting Text command Parameter Sample LANG LANG1# LANG1# 1:CHINESE， Parameter LANG0# LANG0#：ENGLISH ；When check the location, it will reply the Chinese Command location in Chinese language setting; while reply the Description URL link when in English language setting. Command Successful Setting：SET LANG OK！...
  • Page 21 Description information of the device Command Reply with longitude and altitude, speed and IMEL. Feedback 19)Google Link Text command Parameter Sample command 666# 666# Command Check the location link of Google map Description Command <Datetime:12-07-05 13:21:30> Feedback http://maps.google.com/maps?q=N22.540885,E113.95265 20)Version Text command Parameter Sample VERSION...
  • Page 22 Description Command VERSION:Xxxx Feedback BUILD:2012-07-05 10:12 21)Param Check Text command Parameter Sample PARAM 886# 886# Command The command is to check the settings and the default Description parameter. IMEI:351190012535936 APN : cmnet IP:IP and port Command TIMER: moving uploading interval Feedback STATIC: static uploading interval CENTER: center number...

  • Page 23: Status Check

    GMT: time zone (E/W8) 22)Status Check Text command Parameter Sample STATUS 902# 902# Command The command is designed for checking the device’s Description working status. External power:ON/OFF GSM Signal:HIGH/MIDDLE/LOW Command GPS:FIXED/UNFIXED Feedback RELAYER:DISABLE/ENABLE Vibrate Warning:ON/OFF Pause:ON/OFF Monitor (Voice Surveillance) Text command Parameter Sample...

  • Page 24: Troubleshooting

    SSS# SSS# SSS# Command Using Command Send this command to the tracker’s Description number, the tracker will call back to admin number. Command Feedback 10.Trouble shooting 10.1 The device is not online or offline on the web platform. 10.1.1 First, please check the three LED working state. If possible.
  • Page 25 b)If the green GSM LED is not in constant glow, please check the installation of SIM card. 10.1.2 Please check the offline area in order to judge if the network problem of operators. 10.2 When GPS cannot receive the signals, please drive in the open sky and ensure there is no metal thins on the device.

Table of Contents

Save PDF