Sealey GDM50B Instructions

Thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: plEaSE rEaD THESE iNSTrUCTiONS CarEFUllY. NOTE THE SaFE OpEraTiONal rEQUirEMENTS, WarNiNGS aND CaUTiONS.
USE THiS prODUCT COrrECTlY aND WiTH CarE FOr THE pUrpOSE FOr WHiCH iT iS iNTENDED. FailUrE TO DO SO MaY CaUSE
DaMaGE aND/Or pErSONal iNJUrY, aND Will iNValiDaTE THE WarraNTY. plEaSE KEEp iNSTrUCTiONS SaFE FOr FUTUrE USE.
1. SaFETY iNSTrUCTiONS
1.1. ElECTriCal SaFETY. p WarNiNG! it is the user's responsibility to read, understand and comply with the following:
You must check all electrical equipment and appliances to ensure they are safe before using. You must inspect power supply leads, plugs and
all electrical connections for wear or damage. You must ensure the risk of electric shock is minimised by the installation of appropriate safety
devices. An RCCB (Residual Current Circuit Breaker) should be incorporated in the main distribution board. We also recommend that an RCD
(Residual Current Device) is used with all electrical products. It is particularly important to use an RCD with portable products that are plugged
into an electrical supply not protected by an RCCB. If in doubt consult a qualified electrician. You may obtain a Residual Current Device by
contacting your Sealey dealer. You must also read and understand the following instructions concerning electrical safety.
1.1.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on business premises, to be tested by
a qualified electrician, using a Portable Appliance Tester (PAT), at least once a year.
1.1.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure the insulation on all cables and the product itself is safe before connecting to the mains power
See 1.1.1. & 1.1.2. above and use a Portable Appliance Tester (PAT).
1.1.4. Ensure that cables are always protected against short circuit and overload.
1.1.5. Regularly inspect power supply leads and plugs for wear or damage and connections to ensure that none
is loose.
1.1.6. Important: Ensure the voltage marked on the product is the same as the electrical power supply
to be used, and check that plugs are fitted with the correct capacity fuse. A 13 amp plug may
require a fuse smaller than 13 amps for certain products (subject to 1.1.10. below).
1.1.7. DO NOT pull or carry the powered appliance by its power supply lead.
1.1.8. DO NOT pull power plugs from sockets by the power cable.
1.1.9. DO NOT use worn or damage leads, plugs or connections. Immediately replace or have repaired by
a qualified electrician. Where a U.K. 3 pin plug with ASTA/BS approval is fitted, in case of
damage, cut off and fit a new plug according to the following instructions (discard old plug safely).
(UK only - see diagram at right). Ensure the unit is correctly earthed via a three-pin plug.
a) Connect the gREEN/YEllOW earth wire to the earth terminal 'E'.
b) Connect the bROWN live wire to the live terminal 'l'.
c) Connect the bluE neutral wire to the neutral terminal 'N'.
After wiring, check there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends past the cable restraint and that the cable restraint is tight.
Double insulated products are often fitted with live (BROWN) and neutral (BLUE) wires only. Double insulated products are always
marked with this symbol
wires to the earth terminal.
1.1.10. NOTE: If this product requires more than a 13 amp electrical supply, then NO plug is fitted. You must therefore contact a qualified
electrician to ensure a 30 amp fused supply is available. We recommend you discuss the installation of a industrial round pin plug and
socket with your electrician.
1.1.11. Cable extension reels. When a cable extension reel is used it should be fully unwound before connection. A cable reel with an RCD
fitted is recommended since any product which is plugged into the cable reel will be protected. The section of the cores in the cable
is important and should be at least 1.5mm², but to be absolutely sure that the capacity of the cable reel is suitable for this product and
for others that may be used in the other output sockets, the use of 2.5mm² section is recommended .
1.2 GENEral SaFETY
WarNiNG! Disconnect drill from mains power before changing accessories, servicing or performing any
p
maintenance.
Maintain the drill in good condition (use an authorised service agent).
3
WarNiNG! Keep all guards and holding screws in place, tight and in good working order. Check regularly
p
for damaged parts. a guard, or any other part, that is damaged must be repaired or replaced before the
tool is next used, to ensure that it will operate properly and perform its intended function. The safety
guard is a mandatory fitting where the drill is used in premises covered by the Health & Safety at Work act.
Check alignment of moving parts and check for possible broken parts.
3
Replace or repair damaged parts. Use recommended parts only. Non-authorised parts may be dangerous and
3
will invalidate the warranty.
Ensure the set screws of the head frame are screwed tight before using the drill.
3
Secure the drill to a supporting structure to avoid the machine tipping, sliding or walking. Drill is designed for
3
use with drill bits only. No other accessory may be used.
Ensure the chuck is securely fastened to the spindle.
3
Remove adjusting keys and wrenches from the machine and working area before switching on.
3
Use clamps or a vice (not included) to secure the workpiece. Available from your Sealey dealer.
3
DO NOT secure the workpiece by hand.
Refer to speed chart for recommended drilling speeds.
3
WarNiNG! always wear approved eye or face protection when operating this drill. Use a face or dust
p
mask if dust is generated.
WarNiNG! DO NOT wear gloves when drilling.
p
. To re-wire, connect the brown & blue wires as indicated above. DO NOT connect the brown or blue
Original Language Version
INSTRUCTIONS FOR:
BENCH MOUNTED pillar Drill
GDM50B (GDM50BX)
MODEL No:
Yellow & Green
Earth wire
Blue
Neutral
wire
rEplaCEMENT FUSES MUST
BE OF THE SaME TYpE aND
raTiNG aS THE OriGiNal
GDM50B (GDM50BX) Issue: 3 - 05/03/12
supply.
Brown
Live
wire
Cable
restraint