Do you have a question about the Ready2Grow and is the answer not in the manual?
Questions and answers
Julie Wohlt
April 10, 2025
Hello. I have a ready2grow stroller model number 1934625 manufactured 8/29/2018. I’m looking to buy a replacement parents tray and an elevated rear seat. Are these items available? I did not see them on the website site
Page 2
Failure to follow these warnings and the assembly instructions could result in serious injury or death. PLEASE SAVE OWNER’S USE OF THE elevated rear seat MANUAL FOR FUTURE USE. with a child weighing more than ADULT ASSEMBLY REQUIRED. 40 lbs (18.1 kg) or taller than 43 in.
Page 3
READ THE MANUAL provided with your Graco car seat before using it with your stroller. Front tray MUST be installed in the front location to be used for the car seat.
Page 4
Check that you have all the parts for this model BEFORE assembling your product. If any parts are missing, call Customer Service. No tools required.
Page 5
To Open Stroller CHECK that the stroller is completely latched open every time you open the stroller and before continuing with the rest of the assembly steps. SNAP!
Page 6
Attach tray by sliding onto mounts as shown. Secure tray to the stroller with the 2 screws provided.
Page 7
SNAP! Rotate tray down until it snaps into place. SNAP! Never use stroller without the parent tray completely latched into place.
Page 8
BEFORE attaching wheel: Be sure to place stroller on top of a piece of card board or some other protective cover to prevent any damage to floor. WARNING Choking Hazard: Remove and immediately discard foam on the rear axle. Insert brake assembly onto rear legs.
Page 9
Hooks Slide the sides of the standing platform onto the frame legs as shown. Lift the standing platform up and make sure the 3 hooks latch onto the crossbrace as shown.
Page 10
Check that the tabs on both sides of the standing platform are snapped in place. SNAP! Firmly attach hub adapter onto wheel.
Page 11
Place wheel on axle. Place washer on axle.
Page 12
Push straight side of pin through axle hole. Pin will separate around the axle. Curved end of pin MUST face up as shown. SNAP! Snap hubcap over pin as shown. Repeat steps 1-5 (Rear Wheels ) on other side.
Page 13
Attach footrest as shown. Make sure to slide the peg into the channel of the footrest.
Page 14
Insert the tab over the footrest pin as shown.
Page 15
Check that wheels are securely attached by pulling SNAP! on wheel assemblies.
Page 16
Canopy Insert small canopy into the Small canopy canopy mounts on each side of the stroller, with the padded edge facing towards the front as shown. Large canopy Insert large canopy into the canopy mounts on each side of the stroller, with the padded edge facing towards the rear as shown.
Page 18
WARNING Always secure your child with the seat belt. The tray is not a restraint device. DO NOT lift the stroller by the child’s tray. Use care when snapping the tray on the stroller with a child in the stroller. SNAP! To open the tray.
Page 19
WARNING Do not allow child to stand on seat. Never use seat in vehicle or in any other product. Attach seat as shown. Make sure seat is snapped securely onto pegs on each side of the frame. SNAP!
Page 20
You must first attach the hook on the flap to the stroller frame before fastening the snap. Fasten the snap button to the stroller frame as shown. Repeat on other side.
Page 21
Insert the crotch strap buckle into the underside of the parent tray. SNAP! To release crotch strap, press button as shown. To remove elevated seat, reverse steps.
Page 22
Do not allow child to stand on seat. Never use seat in motor vehicle or on any other product. To access basket, push tabs toward the middle of seat and rotate forward as shown. To close: Push seat up and snap the side tabs into SNAP! place as shown.
Page 23
Use slide adjuster at shoulder and waist for tighter adjustment. To change shoulder harness slots.
Page 24
To convert to 3-pt harness. Use slide adjuster at waist for tighter adjustment. When using bench seat, follow steps 3-5 on this page.
Page 25
To Change Shoulder Harness Slots Slide adjuster Remove harness covers as shown.
Page 26
Remove head support as shown. Remove both shoulder harness straps as shown.
Page 27
WARNING When making adjustments to the stroller seat, make sure child’s head, arms, and legs are clear of moving seat parts and stroller frame. Recline strap Recline tab...
Page 28
To recline, pull recline tab down. To raise, pull recline strap...
Page 29
Head Support (on certain models) Only use this head support on this stroller. Never use this head support on any other product. WARNING CHECK that brake is on by trying to push stroller.
Page 30
Front swivel wheels lock for use on uneven surfaces such as grass, stones or gravel.
Page 31
Before folding stroller:(1) remove infant carrier if in use; (2) adjust seat back to upright position; (3) lock brake. (4) fold canopies...
Page 32
® To Attach Graco Infant Car Seat on Elevated Rear Seat WARNING Do not allow child to stand on seat. Never use seat in vehicle or in any other product. Flaps Check to make sure the flaps are installed before beginning to attach infant carseat to the elevated rear seat.
Page 33
Remove head support and harness covers. Remove both shoulder harness straps and the waist straps as shown.
Page 34
Mounts Push seat pad down into the seat to expose the Click Connect™ mounts on either side of the seating area. Insert carseat into stroller and push down on car seat until the latches snap into the Click Connect™ mounts. Check that infant car seat is securely attached by pulling up on it.
Page 35
To remove car seat: squeeze release handle at back of car seat, and lift car seat out of the stroller. ® To Attach Graco Infant Car Seat to Front Seat Remove small canopy.
Page 36
Open flaps inside seating area to expose Click Connect™ mounts. Recline the stroller seat back to its lowest position and insert carseat into stroller and push down on car seat until the latches snap into the Click Connect™ mounts.
Page 37
Check that infant car seat is securely attached by pulling up on it. SNAP! To remove car seat: squeeze release handle at back of car seat, and lift car seat out of the stroller.
Page 38
READY2GROW™ CLICK CONNECT™ Use Positions WARNING DO NOT allow child to stand on platform, facing backwards. To avoid falling, child must hold onto stroller frame.
FROM TIME TO TIME CHECK YOUR STROLLER for loose screws, worn parts, torn material or stitching. Replace or repair the parts as needed. Use only Graco replacement parts. EXCESSIVE EXPOSURE TO SUN OR HEAT could cause fading or warping of parts.
Need help?
Do you have a question about the Ready2Grow and is the answer not in the manual?
Questions and answers
Hello. I have a ready2grow stroller model number 1934625 manufactured 8/29/2018. I’m looking to buy a replacement parents tray and an elevated rear seat. Are these items available? I did not see them on the website site