Summary of Contents for Sunvision Scientific PRO 24S
- Page 1 S S E M B L Y S E R U I D E M O D E L S P R O 2 4 S / 2 4 S F / 2 4 S T 2 8 L X / 2 8 L X F / 2 8 L X 2 F / 2 8 L X T 21166A...
-
Page 2: How To Obtain Service
ifetime Warranty What Is Covered? SUNVISION warrants your tanning unit to be free of structural defects in its material and workmanship, under normal use, for its lifetime. SUNVISION will repair or replace, at their discretion, any defect to the structure which affects the performance of the unit. -
Page 3: Table Of Contents
elcome Congratulations on your purchase of this technologically advanced sun tanning unit. It has been designed to provide years of dependable service for you. Please read all the instructions in this booklet before installing and using the unit. Always be sure to observe all safety precautions. ontents Safety Information................ -
Page 4: Safety Information
21 CFR 1040.20. Other types of eyewear may not provide adequate protec- tion. • Disconnect power cord before attempting to clean, relamp, or engage in the maintenance of this product. ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE MODELS PRO 24S, 28LX: Diamond Sun S Wolff Model 71T12100W ONLY THE FOLLOWING LAMPS HAVE BEEN CERTIFIED FOR USE IN THE MODEL PRO 24SF: Diamond Sun S Wolff Model 71T12100W &... -
Page 5: Installation
nstallation Unpacking and Inspection Your sunbed comes in two cardboard cartons, one for the bench and one for the canopy or top deck. Open the cartons and remove the bench and canopy as follows. The bench and canopy are each wrapped in plastic. With a helper, grasp the bench and pull it from the carton bottom, leaving the plastic wrap and the carton packaging. -
Page 6: Tools Required
Installation-Tools Required Tools Required You’ll need the following tools to assemble your sunbed: Utility Knife #2 Phillips Screwdriver Allen Wrench (Supplied in Hardware Box) -
Page 7: Pre-Installation Planning
Installation-Pre-Installation Planning Pre-Installation Planning Before you begin to assemble your sunbed, you should observe the following pre- installation considerations. • Your sunbed operates from a 220V ac source. You should have an electrical outlet (like the type shown below) installed in the room in which you will use the unit. -
Page 8: Assembly Procedures
Installation-Assembly Procedures Assembly Procedures Hardware Inventory Before you begin, use the utility knife to cut open the Hardware Box and remove the small bag of hardware. In addition to a small allen wrench and pillow, make sure you have the following hardware items. Allen-Head Bolt 5/16"... - Page 9 Installation-Assembly Procedures Attaching Legs to Bench Lay the bench upside down on the floor. Locate the two legs and attach to the bench as shown below. 1. Using the 5/16" x 1 1/2" bolts and the six larger sized 5/16" washers, attach the legs with the skirt mounting holes toward the back of the bed as shown.
- Page 10 Installation-Assembly Procedures Attaching Hinge Brackets to Bench Locate the two hinge brackets and attach to the bench as shown below. 1. Install the hinge bracket to the end of the bed such that the two bosses engage, then secure using the 5/16" x 1" allen-head bolt and 5/16" metal washer. Tighten bolt snug, then an additional half turn.
- Page 11 Installation-Assembly Procedures Attaching Canopy to Bench Attach the canopy to the bench as shown below. This will require at least two people. 1. Lift the canopy and hold it between the hinge brackets. 2. Insert the 5/16" x 1 1/2" bolts with the nylon washers into both hinge brackets. Tighten bolts into the endcap threaded inserts until snug, then an additional half turn.
- Page 12 Installation-Assembly Procedures Attaching Gas Springs Attach the gas springs (located in canopy box) between the canopy and the bench as shown below. You will need another person to help you lift the canopy. 1. With a helper holding the canopy open, align open ends of gas spring ball joints with pivot studs and push into place.
- Page 13 Installation-Assembly Procedures 2. Install two #8 x 1/2” screws through the pre-drilled holes of the side skirt into the back of the leg support. Repeat for the other skirt. PRE-DRILLED HOLES 3. After installing, your sunbed should look like this.
-
Page 14: Making Electrical Connections
Installation-Making Electrical Connections Making Electrical Connections Make electrical connections as shown below. Warning! Be sure ac power is disconnected before connecting cables. 1. Your sunbed is designed to accept an input from a remote control device. The remote control is optional and is not included with your sunbed. If you choose not to use a remote control then, connect the remote control bypass to the remote con- trol connector as shown. -
Page 15: Operation
peration Before You Tan Before using your sunbed, please note the following important precautions: • Your skin should be free of cosmetics, tanning oils, or other body lotions prior to tanning except for those specifically made for use with tanning devices. -
Page 16: Using Your Sunbed
Operation-Using Your Sunbed Using Your Sunbed Once you have read Before You Tan and Exposure Times, you are ready to use your sunbed. Proceed as follows. WARNING! Your sunbed is designed for individual use. Only one pair of protective goggles is provided. Always wear these or another approved pair of goggles. Regular sunglasses do not provide adequate protection from ultra-violet light. -
Page 17: Care And Maintenance
are & Maintenance Cleaning After Use Clean and disinfect your tanning bed’s bench and canopy after each use. Use a non-abra- sive disinfectant cleaner that does not contain ammonia or ammonia derivatives. Ammonia may damage the acrylic shield. Spray the acrylic lightly with disinfectant and wipe dry with a clean soft cloth. -
Page 18: Replacing Lamps
Care & Maintenance-Replacing Lamps Replacing Lamps Introduction Your tanning bench has an hour meter which keeps track of how many hours the sunbed has been in operation. Use this meter to determine when your tanning lamps should be replaced. To be assured of maximum tanning effectiveness, change lamps after approximately 800-1000 hours of use. - Page 19 Lamp Model Number Pro 24ST Diamondsun S Wolff Model 71T12100W Canopy and Bench Pro 28LXT Turbo Face Tanner Turbo Sun S Wolff Model F8-T5-10W Application Lamp Model Number Pro 24S Canopy and Bench Pro 28LX Diamondsun S Wolff Model 71T12100W...
- Page 20 Care & Maintenance-Replacing Lamps Removing/Replacing Face Tanner Lamp on F Models After removing the canopy acrylic shield, replace the face tanner lamp as follows: Step 1. Support the face tanner assembly with your hand while unscrewing the two retaining screws. The face tanner glass casing will now swing downward.
-
Page 21: Timer Maintenance
Care & Maintenance-Timer Maintenance Timer Maintenance Your SUNVISION sunbed is equipped with a backup shut-off timer which will automatically turn off the sunbed in the unlikely event of a malfunction of the pri- mary timer. This important safety feature also prevents the user from re-setting the timer before the end of the pre-set maximum time interval. -
Page 22: Troubleshooting
roubleshooting Problem/Solution Chart Problem Solution Lamps fail to light 1. Check source of ac power. Reset circuit breaker or replace fuse if necessary. 2. Make sure the unit is plugged into outlet. 3. Make sure cord between canopy and bench is properly connected. -
Page 23: Obtaining Service
btaining Service To arrange for service, or for more information about your sunbed, contact ETS as follows: CALL FOR SERVICE OR QUESTIONS: 1•800•228•6292 6270 Corporate Drive Indianapolis, IN 46278-2900 Have the following information ready when calling ETS to order parts or service for your bed: Date Purchased Canopy Serial Number Bench Serial Number...
Need help?
Do you have a question about the PRO 24S and is the answer not in the manual?
Questions and answers