Page 1 INTELLIKNIGHT ® 5820XL Addressable Fire System Installation and Operations Manual Part Number 151209 Rev N...
Page 3 Do not tighten screw terminals more than 9 in-lbs. Over-tightening may damage threads, resulting in reduced terminal contact pressure and difficulty with screw terminal removal. Silent Knight fire alarm control panels contain static-sensitive components. Always ground yourself with a proper wrist strap before handling any circuits so that static charges are removed from the body.
Page 4 While installing a fire alarm system may make lower insurance rates possible, it is not a substitute for fire insurance! An automatic fire alarm system - typically made up of smoke detectors, heat detectors, manual pull stations, audible warning devices, and a fire alarm control with remote notification capability - can provide early warning of a developing fire.
Page 5: Table Of Contents
About this Manual ............................ 1-2 1.2.1 Terms Used in this Manual ....................... 1-2 Compatible Products ..........................1-3 How to Contact Silent Knight ........................1-4 Limitations of Fire Alarm Systems ..................1-5 Requirements and recommendations for proper use of fire alarm systems including smoke detectors and other fire alarm devices: ..................
Page 6 Control Panel Installation ...................... 4-1 Mounting the Control Panel Cabinet ....................... 4-1 4.1.1 Preventing Water Damage ........................ 4-1 4.1.2 Removing the 5820XL Assembly from the Housing ............... 4-1 AC Connection ............................4-2 Battery Connection ..........................4-3 4.3.1 RBB Accessory Cabinet ........................4-4 4.3.1.1 Installing the RBB Accessory Cabinet and Batteries .............
Page 7 6.2.2 Output Circuit Mapping ........................6-6 6.2.3 Zone Event Mapping ........................6-7 6.2.4 Mapping LED Points ........................6-9 Programming Using the 5660 Silent Knight Software Suite ..............6-10 Programming Using an Annunciator ..................... 6-10 6.4.1 Entering & Exiting the Program Menu ................... 6-11 6.4.1.1 Moving through the Menus ....................
Page 8 IntelliKnight 5820XL Installation Manual 6.4.1.3 Editing Keys ......................... 6-12 Programming Menu Quick Reference ....................6-13 Section 7 Programming ............................7-1 UL 864 Programming Requirements ....................... 7-1 Modules ..............................7-1 7.2.1 Edit Modules ............................. 7-2 7.2.1.1 Naming Modules ........................7-2 7.2.1.2 Setting the 5815XL Wiring Class ..................7-3 7.2.2 Adding a Module ..........................
Page 9 Contents Select Account (ID) ......................7-29 Edit Account Number ......................7-29 Select Reporting Format ...................... 7-29 Events to Report ........................7-30 Switch Attempts ........................7-30 Fail Attempts ........................7-30 Selecting Primary and Secondary Phone Lines ..............7-30 Telephone Number ....................... 7-31 7.6.1.2 Auto Test Time ........................
Page 10 IntelliKnight 5820XL Installation Manual 7.9.1.3 Panel Functions ........................7-48 Section 8 System Operation ..........................8-1 User and Installer Default Codes ......................8-1 Annunciator Description .......................... 8-1 8.2.1 LCD Displays ........................... 8-2 8.2.2 Banner ............................... 8-2 Key Operation ............................8-2 Menu System ............................8-3 8.4.1 Main Menu Overview ........................
Page 11 11.1 SLC Point Record ..........................11-1 11.2 Conventional Output Point Record ......................11-8 Appendix A Compatible Devices ........................A-1 Two-Wire Smoke Detectors ........................A-11 Appendix B Special Characters Lists ......................B-1 Characters used for Naming ........................B-1 Silent Knight Fire Product Warranty and Return Policy 151209...
Page 12 IntelliKnight 5820XL Installation Manual 151209...
Page 13: Introduction
The IntelliKnight 5820XL Fire Alarm Control/Communicator is an addressable fire control system that meets the requirements of UL 864. Overview of Basic System The IntelliKnight 5820XL base system is packaged as an assembled stack of 3 circuit boards mounted to an aluminum housing. 1.1.1 Hardware Features •...
Page 14: About This Manual
About this Manual This manual is intended to be a complete reference for all installation and operation tasks for the 5820XL. Please let us know if the manual does not meet your needs in any way. We value your feedback! 1.2.1...
Page 15: Compatible Products
Dimensions: 16" W x 10" H x 6" D (40.64 cm W x 25.4 cm H x 15.24 cm D) Note: Models SD500-FRCM, SD500-FRCM-4 and SD505-ARM are no longer manufactured, but they are still compatible with the IntelliKnight system. Contact Silent Knight if you need information about these mod- ules.
Page 16: How To Contact Silent Knight
IntelliKnight 5820XL Installation Manual The following modems have been tested by Silent Knight for compatibility with the 5820XL and the Silent Knight Software Suite software packages: Table 1-3: Compatible Modems Manufacturer Model US Robotics 28.8 LifeStyle Motorola 28.8, 3400 series Premier 33.6...
Page 17: Limitations Of Fire Alarm Systems
Introduction Limitations of Fire Alarm Systems Manufacturer recommends that smoke and/or heat detectors be located throughout a protected premise following the recommendations of the current edition of the National Fire Protection Association Standard 72 (NFPA 72), manufacturer’s recommendations, State and local codes, and the recommendations contained in Guide for the Proper Use of System Smoke Detectors, which is made available at no charge to all installing dealers.
Page 18 IntelliKnight 5820XL Installation Manual • Heat detectors do not sense particles of combustion and are designed to alarm only when heat on their sensors increases at a predetermined rate or reaches a predetermined level. Heat detectors are designed to protect property, not life.
Page 19: Requirements And Recommendations For Proper Use Of Fire Alarm Systems Including Smoke Detectors And Other Fire Alarm Devices
Introduction Requirements and recommendations for proper use of fire alarm systems in- cluding smoke detectors and other fire alarm devices: Early fire detection is best achieved by the installation and maintenance of fire detection equipment in all rooms and areas of the house or building in accordance with the requirements and recommendations of the current edition of the National Fire Protection Association Standard 72, National Fire Alarm Code (NFPA 72), the manufacturer’s recommendations, State and local codes and the recommendations contained in Guide for the Proper Use of...
Page 20 IntelliKnight 5820XL Installation Manual 151209...
Page 21: Agency Listings, Approvals, And Requirements
The REN number is imbedded in the FCC registration number as 10B. If the 5820XL causes harm to the telephone network, the telephone company will notify you in advance that the temporarily discontinuance of service may be required. But if advance notice is not practical, the telephone company will notify the customer as soon as possible.
Page 22: Underwriters Laboratories (Ul)
You may contact the state public utility commission, public service commission or corporation commission for information. Since the 5820XL is a commercial fire alarm panel, it must be connected upstream of all other equipment utilizing the phone lines. If you have questions about the installation, contact your telephone company or a qualified installer.
Page 23: Requirements For Central Station Fire Alarm Systems
Systems 1. Use both phone lines. Enable phone line monitors for both lines. 2. You must program a phone number and a test time so that the 5820XL sends an automatic daily test to the central station. 3. Do not use the ground start option.
Page 24 IntelliKnight 5820XL Installation Manual 151209...
Page 25: Before You Begin Installing
• A battery cable for batteries wired in series Environmental Specifications It is important to protect the 5820XL control panel from water. To prevent water damage, the following conditions should be AVOIDED when installing the units: • Intended for indoor use in dry locations only •...
Page 26: Electrical Specifications
IntelliKnight 5820XL Installation Manual Electrical Specifications Rating Earth Ground Terminal # and Label Description Faults Voltage Current AC input (hot) 120 VAC, 60 Hz 2.5 A Earth ground AC input (neutral) 120 VAC 60 Hz 2.5 A 3.0 Amp Notification and...
Page 27: Wiring Specifications
Before You Begin Installing Rating Earth Ground Terminal # and Label Description Faults Voltage Current Ring Phone Line 1 Telco Ring Phone Line 1 Telco Tip 0Ω Ring Phone Line 1 Premises Ring Phone Line 1 Premises Tip Ring Phone Line 2 Telco Ring Phone Line 2 Telco Tip 0Ω...
Page 28 IntelliKnight 5820XL Installation Manual Figure 3-1 Wire Routing Example 151209...
Page 29: Board Assembly Diagram
Ports Figure 3-2 Model 5820XL Assembly Figure 3-2 shows the circuit boards, metal housing and annunciator that attach the 5820XL assembly to the cabinet. If you should need to remove the board assembly for repair, remove the four mounting nuts which hold the assembly in the cabinet. Then lift the entire assembly out of the cabinet.
Page 30: Calculating Current Draw And Standby Battery
5. Make sure that the total alarm current you calculated, including current for the panel itself, does not exceed 6.0 A. This is the maximum alarm current for the 5820XL control panel. If the current is above 6.0 A you will need to use a notification power expander(s) such as the Silent Knight 5495 or the 5895XL intelligent power expander, to distribute the power loads so that the 5820XL or the power expanders do not exceed their power rating.
Page 31: Current Draw Worksheet
Current For each device use this formula: This column This column Current per number of devices. Standby: 215 mA 215 mA IntelliKnight 5820XL Fire Panel (Current draw from battery) Alarm: 385 mA 385 mA Addressable SLC Devices SD500-AIM SD500-MIM SD500-PS...
Page 32 IntelliKnight 5820XL Installation Manual Standby Alarm Device # of Devices Current per Device Current Current 5860 Remote Fire Alarm Standby: 20 mA (8 max.) Annunciator Alarm: 25 mA 5824 Serial/Parallel Printer Standby/Alarm: 45 mA (2 max.) Interface Module 5895XL IntelliKnight Power (8 max.)
Page 33: Maximum Battery Standby Load
Warning! Silent Knight does not support the use of batteries smaller than those listed in Table 3-2. If you use a battery too small for the installation, the system could overload the battery resulting in the installation having less than the required 24 hours standby power.
Page 34 IntelliKnight 5820XL Installation Manual See Sec. Task (for more info.) SLC Device Hardware Installation Perform these steps before running JumpStart. Connect device bases to the loop. Set device addresses. Physically connect detectors to their bases. Connect relay and contact 5.3 & see device install instructions monitor modules.
Page 35 Before You Begin Installing See Sec. Task (for more info.) Output Point Configuration Conventional notification circuits (circuits 1-6): Enable circuits used for notification appliances through programming, if 7.4.1 necessary. (JumpStart enables circuits 1-6 as Notification.) Conventional relay circuits (circuits 7-8): Select options for relay circuits, if desired.
Page 36 IntelliKnight 5820XL Installation Manual 3-12 151209...
Page 37: Control Panel Installation
Water damage is not covered under warranty. 4.1.2 Removing the 5820XL Assembly from the Housing If it should ever be necessary to remove the control panel assembly from the cabinet for repair, do so by unscrewing the nuts that connect the control panel assembly to the cabinet. Do not attempt to disassemble the circuit boards.
Page 38: Ac Connection
IntelliKnight 5820XL Installation Manual AC Connection At installation, connect the AC terminals to the power source as shown in Figure 4-1. It may be necessary for a professional electrician to make this connection. The AC terminals are rated at 120 VAC, 50 or 60 Hz, 2.5A.
Page 39: Battery Connection
Control Panel Installation Battery Connection The control panel battery charge capacity is 7.0 to 35 AH. Use 12V batteries of the same AH rating. Determine the correct AH rating as per your current load calculation (see Section 3.6). Wire batteries in series to produce a 24-volt equivalent. Do not parallel batteries to increase the AH rating.
Page 40: Rbb Accessory Cabinet
IntelliKnight 5820XL Installation Manual 4.3.1 RBB Accessory Cabinet The Model RBB Accessory cabinet can be used when your backup batteries requirements use backup batteries that are too large to fit into the main control panel cabinet. The RBB cabinet holds batteries up to the 35 AH size. The RBB dimensions are 16" W x 10" H x 6" D (40.64 cm W x 25.4 cm H x 15.24 cm D).
Page 41 Control Panel Installation 3. Run extended battery cable from control panel cabinet through conduit to RBB cabinet. See Figure 4-5. RBB Cabinet Cover Screws Conduit Coupler Conduit RBB Cabinet Cover Screws Figure 4-5 Battery Connections in the RBB Cabinet Note: Figure 4-5 is an example of how the wire connections can be routed. However, any other cabinet knock- outs (on either the main control panel or the RBB cabinet), that are not previously being used may be uti- lized to connect conduit between the two cabinets.
Page 42: Sbus Wiring
IntelliKnight 5820XL Installation Manual SBUS Wiring This section contains information on calculating SBUS wire distances and the types of wiring configurations (Class A and B). 4.4.1 Calculating Wiring distance for SBUS modules The following instructions will guide you in determining the type of wire and the maximum wiring distance that can be used with control panel SBUS accessory modules.
Page 43 Control Panel Installation These cases are marked in the chart with an asterisk (*). Maximum length can never be more than 6,000 feet, regardless of gauge used. (The formula used to generate this chart is shown in the note below). Table 4-1: Wire Distances Per Wire Gauge Using Copper Wire Wiring Distance: SBUS Modules to Panel Total Worst Case...
Page 44: Wiring Distance Calculation Example
IntelliKnight 5820XL Installation Manual Wiring Distance calculation example: Suppose a system is configured with the following SBUS modules: 2 - Module 5860 Fire Annunciator 1 - 5895XL Intelligent Power Expander 1 - 5865 LED Fire Annunciator 1 - 5824 Serial/Parallel Interface Module...
Page 45: Wiring Configurations
Control Panel Installation 4.4.2 Wiring Configurations Figure 4-7 illustrates Class A wiring configuration and Figure 4-8 illustrates Class B configuration. Supervised Power Limited Caution For proper system supervision do not use looped wire under terminals marked A, B, +, and - of the SBUS device connectors.
Page 46: Remote Annunciator 5860 Installation
The optional Model 5860 Remote Annunciator, shown in Figure 4-9, performs the same functions as the on-board annunciator. Operation is identical. Up to 8 annunciators can be added to the IntelliKnight 5820XL system. Figure 4-9 Model 5860 Remote Annunciator, Front View 5860 installation involves the following steps: 1.
Page 47: Mounting The 5860
Control Panel Installation 4.5.1 Mounting the 5860 This section of the manual describes mounting the remote annunciator. The annunciator can be flush- or surface-mounted. Figure 4-10 shows the parts of the annunciator. Instructions for disassembling and mounting appear on the following pages. Figure 4-10 Annunciator Parts 151209 4-11...
Page 48: Flush Mounting
IntelliKnight 5820XL Installation Manual The 5860 comes from the factory fully assembled. You must disassemble it for mounting. To disassemble the annunciator, use a 5/64 hex wrench to remove the set screws, located on the bottom of the annunciator bezel. (See Figure 4-11 for location of the set screws.) Figure 4-11 Annunciator Back Box and Bezel Details 4.5.1.1 Flush Mounting...
Page 49: Flush Mounting With An Electrical Box
Control Panel Installation Flush Mounting with an Electrical Box The 5860 annunciator can be used with the following types of electrical boxes: 4S, single- gang, and double-gang. If an electrical box is used, the box must be 1-3/8” back from the face of the wall to accommodate the annunciator.
Page 50: Surface Mounting
IntelliKnight 5820XL Installation Manual 4. After the annunciator wiring to the panel has been completed (described in Section 4.5.2), replace the electronic assembly in the back box. Place the bezel over the back box and tighten the set screws on the bezel.
Page 51: Model 5860 Connection To The Panel
Control Panel Installation 4.5.2 Model 5860 Connection to the Panel Connect the 5860 to the panel as shown in Figure 4-14. Supervised Power Limited Figure 4-14 Model 5860 Connection to the Panel 151209 4-15...
Page 52: 5815Xl Installation
To install the 5815XL: 1. Make sure power is off at the panel. 2. Mount the 5815XL in the 5820XL, the 5895XL cabinet, or the 5815RMK remote mount- ing kit. Use the standoffs located under the control panel board assembly and secure with screws provided with the 5815XL.
Page 53: 5815Xl Connection To The Panel
Control Panel Installation 4.6.1 5815XL Connection to the Panel Connect the 5815XL to the control panel as shown in Figure 4-16. After the 5815XL is connected to the panel, it must be added to the system. This programming step is described in Section 4.10.
Page 54: 5824 Serial/Parallel Interface Module Installation
IntelliKnight 5820XL Installation Manual 5824 Serial/Parallel Interface Module Installation The 5824 serial/parallel interface module allows you to connect a printer to the panel, so you can print a real-time log of system events, a report of detector status, and event history.
Page 55: Selecting 5824 Options
Control Panel Installation Model 5824 (with housing) To Serial Printer To Parallel Printer Figure 4-18 Printer Connection 4.7.1 Selecting 5824 Options Configuring the 5824 includes the following steps: • Add the module to the system. JumpStart will add the module automatically (see Section 6.1).
Page 56: Printer And Output Port Options
IntelliKnight 5820XL Installation Manual Printer and Output Port Options 1. From the Installer Main Menu, select for Program Menu. 2. Select for Module. 3. Select for Edit Module. 4. From the list that displays, select the 5824 module you want to configure.
Page 57: 5880 Led I/O Module
Control Panel Installation 5880 LED I/O Module The 5880 is an LED driver board that can be used in a wide variety of applications, including as an interface with most customized floor plan annunciator boards. The 5880 can drive up to 40 LEDs and has one PZT controller.
Page 58: Facp Connection
IntelliKnight 5820XL Installation Manual 4.8.2 FACP Connection The 5880 connects to the panel via the SBUS. Make connections as shown in Figure 4-21. After the 5880 is connected to the panel, it must be added to the system. This programming step is described in Section 4.10.
Page 59: Led Wiring
Control Panel Installation 4.8.3 LED Wiring There are four 12-pin connectors on the 5880 board for connecting LEDs. Each LED gets its power from Pin 11. Internal resistors are sized so that there is approximately 10 mA of current for each LED, no series resistors are required. LED outputs can be mapped to output circuits. See Section 6 for programming details.
Page 60: Dry Contact Wiring
IntelliKnight 5820XL Installation Manual 4.8.4 Dry Contact Wiring The 8 input circuits on the 5880 board are for monitoring switch inputs-any type of switch supported by the control panel can be used with the 5880. For example, you can use a 5880 to monitor pull stations, water flow, tamper, reset, or silence switches.
Page 61: 5865-3 / 5865-4 Led Annunciator Installation
Control Panel Installation 5865-3 / 5865-4 LED Annunciator Installation The 5865-3 and 5865-4 are LED annunciators. The 5865-4 has 30 mappable LEDs, remote silence and reset key switches, and a general system trouble LED. The 5865-3 has 30 mappable LEDs only. These are arranged as 15 pairs of red (typically used for alarm) and yellow (typically used for trouble) LEDs.
Page 62: Facp Connection
IntelliKnight 5820XL Installation Manual 4.9.1 FACP Connection The 5865 connects to the panel via the SBUS. Make connections as shown in Figure 4-25. After the 5865 is connected to the panel, it must be added to the system. This programming step is described in Section 4.10.
Page 63: 5865 Mounting
Control Panel Installation 4.9.2 5865 Mounting Mount the 5865-4 to a standard 4-gang electrical box. Mount the 5865-3 to a standard 3-gang electrical box. In Figure 4-26, the 5865-4 attached to a 4-gang box is used as an example. Figure 4-26 5865 Mounting Example The 5865 ships with a set of zone description labels that can be inserted into the 5865 board assembly.
Page 64: Configuring Modules
IntelliKnight 5820XL Installation Manual 4.10 Configuring Modules This section describes how to configure any system hardware modules that have been added to the system. 4.10.1 Assigning Module IDs When installing a hardware module (such as, 5815XL, 5824, 5860, 5895XL, 5865-3 or 5865- 4), you must use the dipswitches on the module to assign an ID# to the module.
Page 65: Telephone Connection
4.11 Telephone Connection Connect the telephone lines as shown in Figure 4-29. The Model 7860 phone cord is available from Silent Knight for this purpose. A number of programmable options are available for customizing telephone lines. These options are described in Section 7.6.
Page 66: Flexputs ™ I/O Circuits
IntelliKnight 5820XL Installation Manual ™ 4.13 Flexputs I/O Circuits The six Flexput™ circuits are an innovative and versatile feature of the control panel. They can be used as: Class A or B notification circuits, Class A or B initiation circuits (either 2 or 4 wire detectors), or as auxiliary power (resettable, continuous, or door holder).
Page 67 Control Panel Installation 2. Configure the circuit through programming (see Section 7.5). Alarm Polarity Notification Wiring UL Listed EOL Supervised Model 7628 Power Limited 4.7 kΩ Max. Impedance: 1.5Ω Regulated 24 VDC Full Wave Rectified 27.4 VDC, 3A per Circuit, 6A max Combined Figure 4-30 Class B Notification Appliance Circuit Wiring 151209 4-31...
Page 68: Class A Notification Wiring
IntelliKnight 5820XL Installation Manual 4.13.1.2 Class A Notification Wiring You must use an appliance from the list of compatible appliances in the Appendix at the back of this manual. To install a Class A notification appliance circuit: 1. Wire the Class A notification appliances as shown in Figure 4-31.
Page 69: Conventional Input Switch Circuits
Control Panel Installation 4.13.2 Conventional Input Switch Circuits This section of the manual explains how to install conventional initiating devices for Class A (Style D) or Class B (Style B) configurations. 4.13.2.1 Class B Inputs You can connect conventional Class B switches, such as waterflow switches and pull stations, directly to the Flexput circuits of the control panel.
Page 70: Class A Inputs
IntelliKnight 5820XL Installation Manual 4.13.2.2 Class A Inputs You can connect conventional Class A switches, such as waterflow switches and pull stations, directly to the Flexput circuits of the control panel. To install a Class A switch: 1. Wire the Class A switch as shown in Figure 4-33.
Page 71: Installing 2-Wire Smoke Detectors
Control Panel Installation 4.13.3 Installing 2-Wire Smoke Detectors Any compatible U.L. listed two-wire smoke detector can be used with the control panel (see Appendix A for list of compatible smoke detectors). Figure 4-34 and Figure 4-35 illustrate how to connect a UL listed 2-wire detector to the control panel. 4.13.3.1 Installing 2-Wire Class B Smoke Detectors To install a Class B two-wire smoke detector, wire as shown in Figure 4-34.
Page 72: Installing 2-Wire Class A Smoke Detector
IntelliKnight 5820XL Installation Manual 4.13.3.2 Installing 2-Wire Class A Smoke Detector To install a Class A two-wire smoke detector, wire as shown in Figure 4-35. Supervised Power Limited Note: Flexput circuit 5 and 6 used as an example. Any Flexput point pairing could be used.
Page 73: Installing 4-Wire Smoke Detectors
Control Panel Installation 4.13.4 Installing 4-Wire Smoke Detectors Any compatible U.L. listed four-wire smoke detector can be used with the control panel (see Appendix A for list of compatible smoke detectors). Figure 4-34 and Figure 4-35 illustrate how to connect a UL listed four-wire detector to the control panel. 4.13.4.1 Installing a Class B 4-Wire Smoke Detector Figure 4-36 illustrates how to install a 4-wire Class B smoke detector.
Page 74: Installing 4-Wire Class A Smoke Detectors
IntelliKnight 5820XL Installation Manual 4.13.4.2 Installing 4-Wire Class A Smoke Detectors Figure 4-37 illustrates how to install 4-wire Class A detectors. Conventions used for wiring 4-wire Class A loops: 1. Up to two Class A 4-wire loops can be connected to the control panel at once.
Page 75: Auxiliary Power Installation
Control Panel Installation 4.13.5 Auxiliary Power Installation Flexput Circuits 1-6 on the control panel can be used as auxiliary power circuits. The three types of auxiliary power available are: • Door Holder (see Section 4.13.5.1) • Constant (see Section 4.13.5.2) •...
Page 76: Resettable Power
IntelliKnight 5820XL Installation Manual 4.13.5.3 Resettable Power Resettable power is typically used to power beam detectors, flame detectors and conventional 4-wire smoke detectors. For circuits selected as Resettable, 24-volt power is always present at the terminals unless a system reset occurs. If a system reset occurs, power is disconnected from the terminals for 30 seconds, then re-applied.
Page 77: Remote Station Applications
Control Panel Installation 4.15 Remote Station Applications 4.15.1 Keltron Model 3158 Installation The control panel is compatible with Keltron Model 3158, used for direct connection to a Keltron receiver. The 3158 reports alarms, supervisories, and troubles. The steps for connecting the 3158 to the control panel. Refer to the 3158 installation instructions for complete information.
Page 78: City Box Connection Using The 5220 Module
IntelliKnight 5820XL Installation Manual 4.15.2 City Box Connection Using the 5220 Module This section describes how to connect the control panel to a local energy municipal fire alarm box or “city box” as required by NFPA 72 Auxiliary Protected Fire Alarm systems for fire alarm service.
Page 79: Nfpa 72 Polarity Reversal
Control Panel Installation 4.15.3 NFPA 72 Polarity Reversal Note: Intended for connection to a polarity reversal circuit of a control unit at the protected premises having compatible rating. 4.15.3.1 Using the 5220 Module When the 5220 is wired and programmed for polarity reversal, it reports alarm and trouble events to a remote site.
Page 80: Using The 7644 Module
IntelliKnight 5820XL Installation Manual 4.15.3.2 Using the 7644 Module When the 7644 is used for polarity reversal, it allows alarm and trouble events to be reported to a remote site. Alarms will override trouble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset.
Page 81: Using The Sd500-Arm Addressable Relay Module
Control Panel Installation 4.15.4 Using the SD500-ARM Addressable Relay Module When the SD500-ARM is wired for polarity reversal, it reports alarm and trouble events to a remote site. Alarms will override trouble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset.
Page 82: Using A Mr-201/T Control Relay From Air Products
IntelliKnight 5820XL Installation Manual 4.15.5 Using a MR-201/T Control Relay From Air Products When the MR-201/T control relay is wired for polarity reversal, it reports alarm and trouble events to a remote site. Alarms will override trouble conditions and it will not be possible to reset the remote indicator until the condition is cleared and the control panel is reset.
Page 83: Transmitter Activated By Dry Contacts
This section describes the connection of a UL 864 listed remote station transmitter to the 5820XL FACP dry contacts. The FACP contacts must be supervised by the remote station transmitter module using end-of-line resistors (ELRs) with a value determined by the transmitter manufacturer.
Page 84 IntelliKnight 5820XL Installation Manual 4-48 151209...
Page 85: Slc Device Installation
Section 5 SLC Device Installation Caution! To avoid the risk of electrical shock and damage to the unit, power should be OFF at the control panel while installing or servicing. List of SLC Devices The following SLC devices can be used with the control panel. See the appropriate section number in this manual or the device installation instructions (packaged with the device) for more information.
Page 86: Maximum Number Of Devices
IntelliKnight 5820XL Installation Manual Maximum Number of Devices The 5820XL supports a total of 508 addressable devices. 127 devices can be attached to the FACP. The optional Model 5815XL SLC expander can add another 127 devices. Up to three 5815XLs can be added to the main system to achieve the 508 point capacity.
Page 87 SLC Device Installation Figure 5-1 and Figure 5-2 show how wire length is determined for out-and-back tap and T-tap style wiring. Figure 5-1 Calculating wire run length for a simple out and back tap When using T-taps, the total length of all taps and the main bus must not exceed 40,000 feet. This requirement must be met in addition to the maximum distance requirements for the various wire gauges.
Page 88: Wiring 5815Xl In Style 6 & 7 (Class A) Configuration
IntelliKnight 5820XL Installation Manual 5.3.2 Wiring 5815XL in Style 6 & 7 (Class A) Configuration Figure 5-3 illustrates how to wire the SLC loop for Style 6 or Style 7 Class A installations. Note: Style 6 does not use short circuit isolator devices.
Page 89: Heat And Smoke Dector Installation
SLC Device Installation Heat and Smoke Dector Installation The information in this section applies to the following models: SD505-AHS Heat Detector, SD505-AIS Ionization Smoke Detector, and SD505-APS Photoelectric Smoke Detector. Also see Section 5.10 for information o how to address the dectectors. 5.4.1 Wiring 1.
Page 90: Addressing Devices
IntelliKnight 5820XL Installation Manual Addressing Devices This section tells how to address detectors and modules. 5.5.1 SD505-APS, SD505-AHS, & SD505-AIS The SD505-APS photoelectric smoke detector, SD505-AHS heat detector, and SD505-AIS ionization smoke detector are easily addressed at the FACP. The Installer Code is required to perform this task.
Page 91 SLC Device Installation 7. If you are changing addresses, write the programmed address on the back of the device. 8. To exit press left arrow until fully exited. 151209...
Page 92: Slc Devices With Dip Switches
IntelliKnight 5820XL Installation Manual 5.5.2 SLC Devices with Dip Switches Input and relay module addresses are set using the dip switches on the module board. The chart below shows the available addresses. For example, to select address 3, place dip switches 1 and 2 in the up position.
Page 93 SLC Device Installation 151209...
Page 94 IntelliKnight 5820XL Installation Manual 5-10 151209...
Page 95: Programming Overview
Section 6 Programming Overview This section of the manual is intended to give you an overview of the programming process. Please read this section of the manual carefully, especially if you are programming the control panel for the first time. The JumpStart feature automates many programming tasks and selects default options for the system.
Page 96: Input Points
IntelliKnight 5820XL Installation Manual 6.1.1 Input Points JumpStart will determine the number and type of input points (detectors or contact monitor modules) on each SLC loop. JumpStart assigns the correct detector type (heat, ionization or photoelectric), so the installer does not need to edit device type for detectors. Any contact monitor modules on the system will be assigned type "Manual Pull."...
Page 97 Programming Overview 3. From the next menu, select for JumpStart. 4. The message "WARNING Will DELETE all system options" displays on the LCD. Select Yes to continue. A series of messages displays for the next several seconds. JumpStart scans the SLC loops for devices. This can take several minutes, depending on the number of devices attached.
Page 98: Mapping Overview
IntelliKnight 5820XL Installation Manual Mapping Overview This section of the manual is an overview of mapping. Details about how to select mapping options appear in the appropriate subsections in Section 7. Mapping is an important concept with the control panel. In general terms, mapping is assigning or linking events to outputs that should activate when events occur.
Page 99: Input Point Mapping
Programming Overview 6.2.1 Input Point Mapping Input points are assigned to input zones. Any input point can be assigned to any input zone. (Input points can be assigned to one zone only. An input point can be designated as "Unused," which means it has not been assigned to a zone.) Figure 6-2 Input Point Assignment Example 151209...
Page 100: Output Circuit Mapping
IntelliKnight 5820XL Installation Manual 6.2.2 Output Circuit Mapping Figure 6-3 is a simple example showing how to assign notification and relay output circuits to groups. For an example of a simple floor above/floor below application, see Figure 6-5. Figure 6-3 Assigning Output Circuits to Groups (Example)
Page 101: Zone Event Mapping
Programming Overview 6.2.3 Zone Event Mapping There are 8 types of events that can occur in zones (see below). For each event type, you can activate up to 8 output groups and patterns. If it is necessary to map to more than 8 output groups, an output group template may be used (see Section 7.4.5 for information on output group templates).
Page 102 IntelliKnight 5820XL Installation Manual Figure 6-5 Example of Zone Events Mapped to Output Groups and Patterns 151209...
Page 103: Mapping Led Points
Programming Overview 6.2.4 Mapping LED Points Figure 6-6 is a simple example showing how LED points are mapped to zones and output groups. Typically you would create two output groups for each zone, one for alarms and one for troubles. (LED points are available when Models 5865-3/4 and/or 5880 are used with the system.) Figure 6-6 Example of LED Points Mapped to Output Groups (applies to Models 5865-3/4 and 5880)
Page 104: Programming Using The 5660 Silent Knight Software Suite
Programming Using the 5660 Silent Knight Software Suite You can use the 5660 Silent Knight Software Suite (SKSS) to program the control panel onsite or remotely. SKSS is an optional software package that lets you easily program the control panel using a Windows-based computer and a modem* (not sold by Silent Knight).
Page 105: Entering & Exiting The Program Menu
Programming Overview 6.4.1 Entering & Exiting the Program Menu To enter Program Mode: 1. Enter the Installer Code (factory programmed default code is 5820). 2. The display prompts you to press the key to bring up the Main Menu (see Figure 6-7).
Page 106: Selecting Options And Entering Data
IntelliKnight 5820XL Installation Manual 6.4.1.2 Selecting Options and Entering Data There are several ways to make programming selections using the control panel depending on which screen you are currently using. The chart below is a generic explanation. Press Select from a menu.
Page 107: Programming Menu Quick Reference
Programming Overview Programming Menu Quick Reference This section of the manual lists all Program Menu options in the order they appear on the sub- menus. Default settings are indicated in text or marked with an asterisk. The comments column provide quick information and a reference to a section (if applicable) which has more detailed information.
Page 108 IntelliKnight 5820XL Installation Manual Menu Options/Defaults Comments Enter Name1 Enter Number1 Group Name Section 7.4.1.1 Enter Name2 Enter Number2 Latching *Non- Section 7.4.1.2 Options Latching Latching *SILENCE Silenceable Section 7.4.1.2 NON-SIL Non-Silenceable Section 7.4.1.2 Auto Auto Un-silenced Silencing Unsilence Section 7.4.1.2...
Page 109 Programming Overview Menu Options/Defaults Comments UNUSED PHOTO Select HEAT Latching DETECTOR PHOT DUCT Section 7.5 ION DUCT 2WIRE SMK SUP PHOTO Select SUP DET Latching SUP ION MAN_PULL LATCH WATERFLOW NLATCH SUPERVSY LATCH NLATCH FIREDRILL SILENCE RESET PAS_ACK LATCH ZN_AUX1 Internal and Point Enter Pt...
Page 110 IntelliKnight 5820XL Installation Manual Menu Options/Defaults Comments Enter Pt Input Point Type Select Function Per JumpStart (detector/switch) UNUSED Section 7.5 B NOTIF Select Group A NOTIF Select Type CONSTANT AUX PWR RESETABLE DOOR MAN PULL Select zone Latch and Non-...
Page 111 Programming Overview Menu Options/Defaults Comments For each account (1-4), select: Edit Account # *123456 Account # (6-digit number, identifies account to central station) Section 7.6.1 Edit Format *Contact ID Reporting Format (SIA, S20, Contact ID) Section 7.6.1 Y (Yes) *Yes Section 7.6.1 Report Alarms N (No)
Page 112 IntelliKnight 5820XL Installation Manual Menu Options/Defaults Comments For each phone line (1 & 2), select: Dialing Prefix Up to 9 digits none Section 7.6.2.1 # of Answer Rings Range: 00-15 Number of rings before panel answers a call from a computer Section 7.6.2.2...
Page 113 Programming Overview Menu Options/Defaults Comments 0 - 90 Seconds *30 sec Water Flow delay is the number of sec. before water Water Flow Delay flow alarm is generated. Section 7.6.4.1 0 - 30 hours *3 hrs Low AC Report Delay. Section Low AC Delay 7.6.4.2 Y (Enabled)
Page 114 IntelliKnight 5820XL Installation Manual Menu Options/Defaults Comments Edit Name Edit Access Code System Reset System Silence System Event Ack. Fire Drill Key System Tests Fire Drill Menu Indicator Test Walk Test no-Report Walk Test w/Report Dialer Test Profile 1 is the profile that dictates...
Page 115: Programming
This section of the manual describes how to manually program the control panel from the built-in annunciator. Each subsection discusses these menu options in detail. All options described in this section can be performed using the 5660 Silent Knight Software Suite (SKSS).
Page 116: Edit Modules
IntelliKnight 5820XL Installation Manual 7.2.1 Edit Modules The features that can be edited when this option is selected are module name and class of wiring (Class A or Class B), or features that are specific to the module to be edited.
Page 117: Setting The 5815Xl Wiring Class
Programming 7.2.1.2 Setting the 5815XL Wiring Class 8. Choose the class of wiring you wish to use for this module by pressing the arrow, then press 7.2.2 Adding a Module If you need to add a new hardware module to the system, follow these steps. You must be in the Main Menu to perform this task.
Page 118: Deleting A Module
IntelliKnight 5820XL Installation Manual 7.2.3 Deleting a Module If you ever need to delete a module, follow these steps. You must be in the Main Menu to perform this task. If necessary, enter the Installer Code. 1. Enter the installer code.
Page 119: Edit Zone Name
Programming 7.3.1.1 Edit Zone Name 7. Press to edit the selected zone’s name. A screen similar to the one shown in Figure 7-2 displays. Figure 7-2 Selecting Character for Zone Name 8. Select the characters for the zone name by pressing the arrow until the desired character is shown then press Enter the Numerical Designator for the character you want, then press...
Page 120: Alarm Delay Characteristics
IntelliKnight 5820XL Installation Manual Alarm Delay Characteristics 3. Select the alarm delay characteristics (see Table 7-1) by pressing the arrow. Table 7-1: Alarm Delay Characteristics Type of Delay Description One Count (No Delay). When this option is enabled, an alarm occurs immediately when a single device of any of the following types goes into alarm: detector, manual pull, water flow, Aux1 or Aux2.
Page 121: Zone Outputs
Programming 7.3.1.3 Zone Outputs Output groups and cadence patterns are mapped to events. They can be programmed to output when an event occurs in a zone. Some system trouble events can be mapped for the entire system. Section 6.2 of this manual contains a general explanation of mapping. The following sections explain how to select mapping options.
Page 122: Zone Mapping Example
IntelliKnight 5820XL Installation Manual 8. Select options for each event that could occur in this zone. Figure 7-3 is a complete exam- ple of how you might map a zone. Indicates output group 1, cadence pattern 00 has been selected. 00 is a constant output cadence.
Page 123 Programming groups. Figure 7-4 shows how you would program this application. Figure 7-4 Zone Mapping Example 151209...
Page 124: Cadence Patterns
IntelliKnight 5820XL Installation Manual 7.3.1.4 Cadence Patterns The cadence patterns shown in Figure 7-5 are available for use with the control panel. Cadence patterns can be selected by event type for each zone or for the entire system. Special cadence patterns can be selected for fire drills and any auxiliary system switches used with the...
Page 125: Zone Accessory Options
Programming system. Figure 7-5 Cadence Patterns Available with the Control Panel 7.3.1.5 Zone Accessory Options This option applies to detectors that are used with SD505-6SB, SD505-6RB, and SD505-ADHRs. Single or Multi-station cadence pattern (choose from Patterns 00 to 21). Local Zone (choose Y or N, for Yes or No). 7.3.2 Add Zone To add a zone, follow these steps:...
Page 126: Delete Zone
IntelliKnight 5820XL Installation Manual 1. Enter the installer code. 2. Press to display the main menu. 3. Select for Program Menu. Display reads: Initializing Please wait . . . 4. Press to enter zone menu. 5. Press to add a zone.
Page 127: View Zone Points
Programming 7.3.4 View Zone Points To view the points in a zone, follow these steps: 1. Enter the installer code. 2. Press to display the main menu. 3. Select for Program Menu. Display reads: Initializing Please wait . . . 4.
Page 128: Group
IntelliKnight 5820XL Installation Manual Group An output group is made up of output points that have been programmed to respond in the same way. Output groups simplify programming because you have to program the output characteristics that are common to all of the group points once, instead of programming each individual point.
Page 129: Edit Group Properties
Programming 8. Select the characters for the zone name by pressing the arrow until the desired character is shown then press Enter the Numerical Designator for the character you want, then press . See Appendix B of this manual for a list of available characters and their numeric designators. 9.
Page 130: Response With System-Wide Conditions
IntelliKnight 5820XL Installation Manual Table 7-2: Silencing Options Option Description AUT UNSIL Auto Unsilenced. If this option is selected, the output group can be silenced for a programmed time- frame. If the condition that caused the output to activate has not cleared during the time-frame, the output reactivates.
Page 131: Add Group
Programming 16. Press 17. Enable group activation for a condition (see Table 7-3) by pressing the arrows to select Y (yes) or N (no). 18. Press 19. Repeat steps 14 and 15 for all the activation options. 7.4.2 Add Group To add a group: 1.
Page 132: View Group Points
IntelliKnight 5820XL Installation Manual 7.4.4 View Group Points 1. Enter the installer code. 2. Press to display the main menu. 3. Select for Program Menu. Display reads: Initializing Please wait . . . 4. Press to enter group menu. 5. Press to view group points.
Page 133: Point
Programming eight output groups. To create Output Group Templates: 1. From the Main Menu, select for Program Menu. 2. From the Program Menu, select for Group. 3. At the next screen, select for Edit OPG Template. 4. Select the template number (01 - 08). 5.
Page 134 IntelliKnight 5820XL Installation Manual 8. Press 9. Select the type of device by pressing the arrows. Refer to Table 7-5 under col- umn heading "Type Selection" for a list of choices. Table 7-5: Point Programming Options for 5815XL Modules Type...
Page 135 Programming Table 7-5: Point Programming Options for 5815XL Modules Type Latching Function Comments Selection Option Use this switch type for manual pull stations. This input is always latched. MAN_PULL The switch can clear only when an alarm is reset. This switch type has the highest priority;...
Page 136 IntelliKnight 5820XL Installation Manual Table 7-5: Point Programming Options for 5815XL Modules Type Latching Function Comments Selection Option Latching Use these switch types if you want to monitor special zone-level conditions ZN_AUX1 (such as operation of a fan or damper).
Page 137 Programming Table 7-5: Point Programming Options for 5815XL Modules Type Latching Function Comments Selection Option Select LED No. SLC LED Select Group 01 -80 151209 7-23...
Page 138: Point Programming For Internal Or External Power Module (5895Xl)
IntelliKnight 5820XL Installation Manual 7.5.2 Point Programming For Internal or External Power Module (5895XL) To program for an internal or external power module points: 1. Enter the installer code. 2. Press to display the main menu. 3. Select for Program Menu.
Page 139 Programming Press to skip point name edit. 16. Repeat Steps 1 through 15 for all circuits. Table 7-6: Menu choices for Internal/External Power Module Function Choices Type Selections Selections for Comments each Type Enter Point or Circuit UNUSED B NOTIF A NOTIF CONSTANT Constant auxiliary power.
Page 140: Point Programming For 5880 And 5865 Modules
IntelliKnight 5820XL Installation Manual 7.5.3 Point Programming For 5880 and 5865 Modules To program 5880 or 5865 module points: 1. Enter the installer code. 2. Press to display the main menu. 3. Select for Program Menu. Display reads: Initializing Please wait . . .
Page 141: Assigning A Name To Points
Programming 14. Repeat Steps 1 through 13 for all points. 7.5.3.1 Assigning a Name to Points You can assign a name to a point to make it easier to recognize on a display. To edit a point name: 1. Do steps 1 through 4 in Section 7.5.3. 2.
Page 142: Reporting Account
IntelliKnight 5820XL Installation Manual 7.6.1 Reporting Account Up to four reporting accounts can be used with the control panel. Events in accounts are reported by zone. Each account is assigned an up-to-6-digit account number. Each account is also assigned a unique ID (1-4) which determines the priority for reporting ("1"...
Page 143: Edit Accounts
Programming 7.6.1.1 Edit Accounts 6. From the next menu, select for Edit Account. A screen similar to one shown in Figure 7-12 will display. The following subsections describe the options on each field. Figure 7-12 Reporting Account Editing Screen Select Account (ID) The control panel provides up to 4 reporting accounts.
Page 144: Events To Report
IntelliKnight 5820XL Installation Manual Events to Report The next six options select which types of events (or event families) will be reported to this account. (See Figure 7-12 for location of these options on the screen.) Events are reported by zone.
Page 145: Telephone Number
Programming 15. Repeat step 14 for the secondary phone line. Telephone Number Enter up to 40 characters for phone number for this account. The following special characters are available: Table 7-7: Special Character for Dialing Pound (or number) key on the telephone Star key on the telephone Comma (character for 2-second pause) Use the number buttons on the annunciator or the up- and down-arrow keys to select special...
Page 146: Auto Test Time
IntelliKnight 5820XL Installation Manual 7.6.1.2 Auto Test Time To access the automatic dialer test time screen: 1. Enter the installer code. 2. Press to display the main menu. 3. Select for Program Menu. Display reads: Initializing Please wait . . .
Page 147: Dialing Prefix
Programming 6. Select the phone line to be edited (1 or 2) by pressing the arrow, then press Figure 7-13 Phone Lines Editing Screen 7.6.2.1 Dialing Prefix Enter up to 8 characters to be used for such things as PBX dial-out codes, a pause, and so on. The following special characters are available: Pound (or number) key on the telephone Star key on the telephone...
Page 148: Number Of Answer Rings
IntelliKnight 5820XL Installation Manual 7.6.2.2 Number of Answer Rings This option is used in conjunction with the 5660 SKSS . Use the option to determine the number of rings before the panel answers a call from the computer. Range is 00-15 rings. This option is factory-programmed as 06 rings, which should be compatible for most installations where the answering machine bypass feature is used.
Page 149: Answering Machine Bypass
Programming disabled by default. For 5211 installation, see Section 4.12. Note: Ground start cannot be used in UL installations. 12. Select Y (ground start used monitor line) or N (ground start not used don’t monitor line) by pressing the arrow, then press 7.6.2.7 Answering Machine Bypass This option is used in conjunction with the 5660 SKSS.
Page 150: Trouble Events
IntelliKnight 5820XL Installation Manual 7.6.3.1 Trouble Events You can map certain system trouble events to an output group. To access the screen for selecting output groups and cadence patterns for system trouble events. 6. Press for Trouble Events. A screen similar to the one in Figure 7-14 will display. Select a group and a cadence pattern for each event as needed for your application.
Page 151: System Alarm Cadence
Programming 7.6.3.2 System Alarm Cadence Fire drill and system auxiliary alarm events can have special cadence patterns to distinguish them from other types of alarms. See Section 7.3.1.4 for available cadence patterns. A typical use of the System Aux1 and Aux2 patterns is to distinguish fire emergencies from other types of emergencies.
Page 152: Miscellaneous Options 1
IntelliKnight 5820XL Installation Manual 7.6.4 Miscellaneous Options 1 Through this programming option you can set the water flow delay time, low AC report delay, enable or disable automatic daylight savings time adjustment, clock format, and AC clock frequency. 7.6.4.1 Water Flow Delay You can program a delay of 0-90 seconds (zero means no delay) to be used in conjunction with a water flow switch.
Page 153 Programming 6. Enter the number of seconds (0 to 90 ) to delay an a water flow switch alarm, then press 151209 7-39...
Page 154: Low Ac Report Delay
IntelliKnight 5820XL Installation Manual 7.6.4.2 Low AC Report Delay Note: You must select 1-3 hours in UL central station installations and UL remote signaling installations. You can adjust the number of hours before a Low AC report will be sent to the central station.
Page 155: Miscellaneous Options 2
Programming 7.6.5 Miscellaneous Options 2 Through this programming option you can turn the strobe synchronization during silence feature On or Off, and select the control panel to report events by zone or by point. To edit miscellaneous options 2: 1. Enter the installer code. 2.
Page 156: Miscellaneous Options 3
IntelliKnight 5820XL Installation Manual 7.6.6 Miscellaneous Options 3 From Miscellaneous Options 3, you set the alarm verification time, turn the Plex Door option on/off, and set the start and end week and month of Daylight Saving Time. To edit Miscellaneous Options 3: 1.
Page 157: Daylight Saving Time Start And End
Programming 7.6.6.3 Daylight Saving Time Start and End This option lets you to adjust the week and month Daylight Saving Time (DST) starts and ends. For this feature to work, you must enable (set to Yes) the DST option under Misc. Options 1 (see Section 7.6.6.3).
Page 158: Edit Banner Message
IntelliKnight 5820XL Installation Manual 7.6.7 Edit Banner Message The banner is the message that displays on the panel LCD when the system is normal, that is, when no alarms or troubles exist and no one is currently using system menus. You can create a customized message, which can be up to 40 characters, two lines of 20 characters each.
Page 159: Jumpstart Autoprogramming
Programming JumpStart Autoprogramming IMPORTANT! JumpStart is intended to be used prior to performing any custom programming. Each time JumpStart is executed, all options will be reset to their default values. Do not run JumpStart after you have configured the system through programming. To run JumpStart: 1.
Page 160: Computer Account
IntelliKnight 5820XL Installation Manual Computer Account An installer at the panel site can initiate communications between the panel and a computer running the 5660 SKSS (see also Section 8.5.16). In order for this communication to function properly both the computer (running the software) and the control panel must have matching computer account numbers and computer access codes.
Page 161: Access Codes
Programming Access Codes Access codes provide the user access to the control panel functions. Each access code can be customized for each user. This allows some users the ability to access programming and other higher level panel functions, while other users may only need access to lower level functions such as preforming fire drills, or acknowledging trouble conditions.
Page 162: Profile Edit Menu
IntelliKnight 5820XL Installation Manual Please wait . . . 4. Select for System Options. Display reads: Select Profile 01 Fire Fighter’s Key 5. Select the access code you wish to edit by pressing the arrow. 6. Then press 7.9.1 Profile Edit Menu From the Profile Edit Menu you can change the users name, access code, and the panel functions that the user will have access to with their code.
Page 163 Programming 151209 7-49...
Page 164 IntelliKnight 5820XL Installation Manual 7-50 151209...
Page 165: System Operation
Section 8 System Operation Operation of the control panel is simple. Menus guide you step-by-step through operations. This section of the manual is an overview of the operation menus. Please read this entire section carefully before operating the panel. Press to view Main Menu: Select the desired menu option.
Page 166: Lcd Displays
IntelliKnight 5820XL Installation Manual 8.2.1 LCD Displays The control panel LCD displays system messages, annunciates alarms, supervisories and troubles; provides status information; and prompts for input. These messages can be up to 80 characters, displaying over four lines of 20 characters each. Annunciator keys beep when they are pressed.
Page 167: Menu System
These options are described in detail in Section 7. View system information, including model and serial numbers and revision System Info number and date. Initiate communication from the panel site between the panel and a Up/Download computer running the Silent Knight Software Suite. 151209...
Page 168: Using The Menus
IntelliKnight 5820XL Installation Manual 8.4.2 Using the Menus To move through the menus: to move through the options in a menu. Use to move to a previous menu. To select an option: Enter the number of the option. –OR– ENTER...
Page 169: View Event History
System Operation 8.5.4 View Event History Use the View Event History feature to display events on LCD. From the Main Menu, press to select Event History. Events will begin displaying with most recent events first. The panel can store up to 1000 events. When it reaches its 1000-event capacity, it begins deleting, starting with the oldest events.
Page 170: Conduct A Walk Test
IntelliKnight 5820XL Installation Manual 8.5.7 Conduct a Walk Test 1. From the Main Menu, press for System Tests. IMPORTANT! If any alarm verification zones are being used, the user will be asked if they wish to disable alarm verification during walk test. This occurs for either walk test option.
Page 171: Silence Alarms Or Troubles
System Operation 8.5.9 Silence alarms or troubles Press and enter your code or rotate the key at the prompt. If an external silence SILENCE switch has been installed, activating the switch will silence alarms or troubles. If you are already using system menus when you press , you will not need to enter your code or SILENCE rotate the key.
Page 172: View Status Of A Point
IntelliKnight 5820XL Installation Manual 5. A screen similar to those shown in Figure 8-4 will display. Figure 8-4 Checking Detector Sensitivity Compliance If a printer is attached to the system (via a Module 5824 serial/parallel interface module), you can print detector status (see Section 8.5.17).
Page 173: Communicating With A Remote Computer
System Operation 8.5.16 Communicating with a Remote Computer An installer at the panel site can initiate communications between the panel and a computer running the SKSS 5660. You can use this feature to upload a panel configuration. For example, if you have made programming changes to an installation on site using an annunciator, you can send your changes to the computer, so that the central station will have the latest data about the installation.
Page 174: Working With A Printer
IntelliKnight 5820XL Installation Manual 8.5.17 Working with a Printer If you are using the Model 5824 serial/parallel interface module, several printing options are available. See Section 4.7 for information about installing the 5824. 1. From the Main Menu, select Printer Options.
Page 175: Operation Mode Behavior
System Operation Operation Mode Behavior The control panel can be in one of seven conditions at any given moment: Normal, Alarm, Prealarm, Supervisory, Trouble, Silenced, and Reset. Table 8-1 describes the behavior of the panel in each of these modes. Table 8-1: Operation Mode Behavior Operation Occurs When...
Page 176 IntelliKnight 5820XL Installation Manual Table 8-1: Operation Mode Behavior Operation Occurs When System Behavior In This Mode You Can Mode Supervisory The system The dialer seizes control of the phone line Press (down arrow) to view the supervisory detects a and calls the central station.
Page 177 System Operation Table 8-1: Operation Mode Behavior Operation Occurs When System Behavior In This Mode You Can Mode Prealarm A single detector Touchpad PZT beeps. Press (down arrow) to view the prealarm. A trips in a 2- The LCD displays a screen similar to this screen similar to this one displays.
Page 178: Releasing Operations
IntelliKnight 5820XL Installation Manual Releasing Operations This control panel supports two types of releasing, Double Interlock Zone, and Single Interlock Zone. The Double Interlock Zone operation requires an interlock switch input in the system, and the Single Interlock does not. An interlock switch is typically a dry-contact pressure switch.
Page 179: Single Interlock Zone Releasing
System Operation 8.7.1 Single Interlock Zone Releasing A single interlock zone utilizes a minimum of two addressable detectors and a designated manual release switch. Important! Only addressable detectors can be used. No conventional detectors can be used. Each Single Interlock Zone input requires at least one manual release switch. Conditions Required for an Pre-Alert Output Activation If any single addressable detector is activated, the "Pre-Alert"...
Page 180: Double Interlock Zone Releasing
IntelliKnight 5820XL Installation Manual 8.7.2 Double Interlock Zone Releasing A Double Interlock Zone uses a minimum of two Addressable detectors, a designated manual release switch, and an interlock switch input. An interlock switch is typically a dry-contact pressure switch and will be referred to as an interlock/pressure switch in this document.
Page 181: Smoke Alarm Verification
System Operation Smoke Alarm Verification Figure 8-6 illustrates how the Smoke Alarm Verification cycle operates. Figure 8-6 Smoke Verification Cycle During the Confirmation Period if there is no alarm indication then the system will return to normal operation. 151209 8-17...
Page 182 IntelliKnight 5820XL Installation Manual 8-18 151209...
Page 183: Reporting
Table 9-1 shows receivers compatible with the control panel. Table 9-1: Receivers Compatible with the Control Panel Manufacturer Model Format Model 9800 SIA and Contact ID Silent Knight Model 9000 (SIA formats) Ademco Model 685 (Contact ID ) Contact ID Sur-Gard SG-MLR2-DG (V. 1.64 or higher)
Page 184 IntelliKnight 5820XL Installation Manual SIA Reporting Format Contact ID Reporting Format Event Class Module Event Parameter Event Group Contact Event Description (System, Zone, ID # Event Qualifier Family (if any) Code or Point) (if any) Code Panel time has been changed...
Page 185 Reporting SIA Reporting Format Contact ID Reporting Format Event Class Module Event Parameter Event Group Contact Event Description (System, Zone, ID # Event Qualifier Family (if any) Code or Point) (if any) Code SLC LED Module trouble restore Trouble Zone Event 0000 SLC LED Module trouble Trouble...
Page 186 IntelliKnight 5820XL Installation Manual SIA Reporting Format Contact ID Reporting Format Event Class Module Event Parameter Event Group Contact Event Description (System, Zone, ID # Event Qualifier Family (if any) Code or Point) (if any) Code System-based AUX2 switch alarm...
Page 187 Reporting SIA Reporting Format Contact ID Reporting Format Event Class Module Event Parameter Event Group Contact Event Description (System, Zone, ID # Event Qualifier Family (if any) Code or Point) (if any) Code Interlock switch trouble restore Trouble Point Event pi Exp.
Page 188 IntelliKnight 5820XL Installation Manual SIA Reporting Format Contact ID Reporting Format Event Class Module Event Parameter Event Group Contact Event Description (System, Zone, ID # Event Qualifier Family (if any) Code or Point) (if any) Code Water flow switch re-enabled...
Page 189 Reporting SIA Reporting Format Contact ID Reporting Format Event Class Module Event Parameter Event Group Contact Event Description (System, Zone, ID # Event Qualifier Family (if any) Code or Point) (if any) Code An unexpected SLC device has been Trouble Point Event pi Exp.
Page 190 IntelliKnight 5820XL Installation Manual 151209...
Page 191: Testing And Troubleshooting
If these suggestions do not solve your problem or if you encounter a problem that is not listed here, contact Silent Knight Technical Support at 800-328-0103 for assistance. 10.2 Common Problems...
Page 192: Periodic Testing And Maintenance
IntelliKnight 5820XL Installation Manual Problem Possible Cause / Suggested Actions SLC devices are not being recognized Check that SLC loop impedance is within the required range. (trouble message "Missing" displays on To measure impedance, use the following procedure. the annunciator).
Page 193: Event History
Testing and Troubleshooting 3) When necessary, activation of Notification Appliances can be prevented by the DISABLE function Testing: 1) Activate a input via an alarm initiating device and check that the correct outputs activate (Notification Appliances sound/flash, relays activate, alarm LED lights). Reset system. Repeat for each alarm initiating device.
Page 194: Built-In Troubleshooting And Testing Tools
IntelliKnight 5820XL Installation Manual 10.3 Built-in Troubleshooting and Testing Tools The fire control panel has several built-in testing and troubleshooting tools that can be utilized to save time while testing and troubleshooting points and SLC devices. 10.3.1 SLC Device Locator SLC device locator can be used to locate a device on a SLC loop.
Page 195: Slc Multi Locator
Testing and Troubleshooting 10.3.2 SLC Multi Locator This feature is the same as SLC Device Locator, except you can locate up to 8 devices on a single search. Follow these instructions to locate multiple SLC devices: 1. Select (Point Functions) from the Main Menu. 2.
Page 196: I/O Point Control
IntelliKnight 5820XL Installation Manual 10.3.3 I/O Point Control This feature allows you to toggle any output on or off and trip any input device. This can be useful to test a point’s output mapping. Follow these steps to control a I/O point: 1.
Page 197: Earth Fault Resistance
Testing and Troubleshooting 10.3.4 Earth Fault Resistance Table 10-1 lists the earth fault resistance detection for each applicable terminal on the FACP. Table 10-1: Earth Fault Resistance Values by Terminal Terminal Label Low Biased High Biased Terminal Function (Values in Ohms) High High Number...
Page 198 IntelliKnight 5820XL Installation Manual 10-8 151209...
Page 199: Installation Records
Section 11 Installation Records This section of the manual is for you to use if you wish to track of how points, zones, and groups have been programmed. 11.1 SLC Point Record You can use the chart that begins below to keep track of SLC points. Default addresses for ID: On-board: = 33 5815-1:...
Page 200 IntelliKnight 5820XL Installation Manual Table 11-1: Installation Record Zone / Zone/ Module Addr Description Module Addr Description Group Group On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board On-board...
Page 201 Installation Records Table 11-1: Installation Record Zone / Zone/ Module Addr Description Module Addr Description Group Group 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1...
Page 202 IntelliKnight 5820XL Installation Manual Table 11-1: Installation Record Zone / Zone/ Module Addr Description Module Addr Description Group Group 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-1 5815-2 5815-1 5815-2 5815-1 5815-2 5815-1 5815-2 5815-1 5815-2...
Page 203 Installation Records Table 11-1: Installation Record Zone / Zone/ Module Addr Description Module Addr Description Group Group 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2 5815-2...
Page 204 IntelliKnight 5820XL Installation Manual Table 11-1: Installation Record Zone / Zone/ Module Addr Description Module Addr Description Group Group 5815-2 5815-3 5815-2 5815-3 5815-2 5815-3 5815-2 5815-3 5815-2 5815-3 5815-2 5815-3 5815-2 5815-3 5815-2 5815-3 5815-2 5815-3 5815-2 5815-3 5815-2...
Page 205 Installation Records Table 11-1: Installation Record Zone / Zone/ Module Addr Description Module Addr Description Group Group 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3 5815-3...
Page 206: Conventional Output Point Record
IntelliKnight 5820XL Installation Manual 11.2 Conventional Output Point Record This chart can be used to keep track of how conventional output points (circuits) have been configured. Point/Circuit Group Description 11-8 151209...
Page 207: Appendix A Compatible Devices
Appendix A Compatible Devices Notification Appliances For proper operation, you must use polarized devices with a Model 7628 4.7k ohm EOL resistor on each loop. All supervised notification appliances used with the control panel must be polarized. Note: Not all devices can use the Sync feature, be sure to check to ensure the device you have chosen will work with this feature.
Page 208 IntelliKnight 5820XL Installation Manual Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual Type Vibrating Bell Vibrating Bell Single Stroke Bell 2700 -M. -R, -T, -Y, -Z Strobe Faraday 2701 Series Strobe 2705 Series Strobe 2820 Snyc Temporal Horn/Strobe 2821...
Page 209 Compatible Devices Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual Type Faraday 6223 Horn 6226 Horn/Strobe 6227 Horn/Strobe 6228 Horn/Strobe 6243 Electron-Mechanical Horn 6244 Electron-Mechanical Horn 6245 Electron-Mechanical Horn 6246 Electron-Mechanical Horn/Strobe 6247 Electron-Mechanical Horn/Strobe 6248 Electron-Mechanical Horn/Strobe 6300 Mini-Horn 6301 Mini-Horn...
Page 210 IntelliKnight 5820XL Installation Manual Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual Type P2415-FC Horn/Strobe P2415W-FC Horn/Strobe P2415K-FC Horn/Strobe P241575-FC Horn/Strobe P241575W-FC Horn/Strobe P241575F-FC Horn/Strobe P241575K-FC Horn/Strobe P2430-FC Horn/Strobe P2430W-FC Horn/Strobe P2430K-FC Horn/Strobe P2475-FC Horn/Strobe P2475W-FC Horn/Strobe P2475K-FC Horn/Strobe...
Page 211 Compatible Devices Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual Type Gentex HG124 Horn HS24-15 Horn/Strobe HS24-30 Horn/Strobe HS24-60 Horn/Strobe HS24-75 Horn/Strobe HS24-110 Horn/Strobe HS24-1575 Horn/Strobe GCC24 Multi Candella Horn/Strobe Ceiling Mount GCCR24 Multi Candella Horn/Strobe Ceiling Mount GCS24 Multi Candella Strobe Ceiling Mount GCSR24 Multi Candella Strobe Ceiling Mount...
Page 212 IntelliKnight 5820XL Installation Manual Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual Type Chime Chime CHSR 2-Wire Chime/Strobe CHSW 2-Wire Chime/Strobe Horn Horn Horn 2-Wire Horn/Strobe P2R-P 2-Wire Horn/Strobe PC2R 2-Wire Horn/Strobe PC2R-P 2-Wire Horn/Strobe P2RH 2-Wire Horn/Strobe High Candela...
Page 213 Compatible Devices Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual Type System Sensor PC4W 4-Wire Horn/Strobe P4WH 4-Wire Horn/Strobe High Candela PC4WH 4-Wire Horn/Strobe High Candela P4RK 4-Wire Horn/Strobe PC4RK 4-Wire Horn/Strobe P4RHK 4-Wire Horn/Strobe High Candela PC4RHK 4-Wire Horn/Strobe High Candela PC4RH 4-Wire Horn/Strobe High Candela Strobe...
Page 214 IntelliKnight 5820XL Installation Manual Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual Type Wheelock AH-12 Horn AH-24 Horn AH-12WP Horn Weatherproof AH-24WP Horn Weatherproof AMT-241575W Multi-Tone Horn Strobe AMT-24MCW Mutli-Tone Horn Strobe AMT-241575W-NYC Multi-Tone Horn Strobe AMT-12/24 Multi-tone Horn...
Page 215 Compatible Devices Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual Type ASWP-24MCWH Horn/Strobe ASWP-24MCCH Horn/Strobe CH-70 Chime CH-90 Chime CH70-241575W Chime/Strobe CH70-24MCW Chime/Strobe CH70-24MCWH Chime/Strobe CH90-24MCC Chime/Strobe CH90-24MCCH Chime/Strobe HS-24 Horn HS4-241575W Horn/Strobe HS4-24MCW Horn/Strobe HS4-24MCWH Horn/Strobe HS4-24MCC Horn/Strobe Wheelock MIZ-24S Mini Horn Strobe...
Page 216 IntelliKnight 5820XL Installation Manual Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual Type Wheelock NS-241575W Horn/Strobe Con’t NS-24MCW Horn/Strobe NS-24MCC Horn/Strobe NS-24MCCH Horn/Strobe ZNS-MCW Horn/Strobe ZNS-MCWH Horn/Strobe ZNS-24MCC Horn/Strobe ZNS-24MCCH Horn/Strobe RSS-121575W Strobe RSS-241575W Strobe RSS-24MCC Strobe RSS-24MCCR Strobe...
Page 217 Compatible Devices Table A-1: Compatible Notification Appliances Manufacturer Model Audio Visual Type Wheelock RSSWPA-24MCCH Strobe Weatherproof Con’t RSSWPG-24MCCH Strobe Weatherproof RSSWPR-24MCCH Strobe Weatherproof RSSWP-2475W Strobe Weatherproof RSSWP-2475C Strobe Weatherproof RSSWP-24MCWH Strobe Weatherproof ZRS-MCWH Strobe ZRS-24MCC Strobe ZRS-24MCCH Strobe MB-G6-24 Motor Bell MB-G10-24 Motor Bell MB-G6-12...
Page 218: Two-Wire Smoke Detectors
IntelliKnight 5820XL Installation Manual A.3 Two-Wire Smoke Detectors Table A-2 lists two-wire smoke detectors that are compatible with the fire control panel. The table is organized by manufacturer. The columns show the number of detectors per loop that can be used.
Page 219 Compatible Devices Table A-2: Compatible Two-Wire Smoke Detectors Model Name or Number Compatibility ID Manufacturer (Base model name or number # per Loop Head Base in parentheses.) SIH-24F (HS-224D OR HSD- HD-3 HB-5 25 / loop 224) Hochiki SLK-24F (HS-224D) HD-3 HB-5 25 / loop...
Page 220 IntelliKnight 5820XL Installation Manual Table A-2: Compatible Two-Wire Smoke Detectors Model Name or Number Compatibility ID Manufacturer (Base model name or number # per Loop Head Base in parentheses.) 1400 20 / loop 1451 (B401B) 20 / loop 2100 20 / loop...
Page 221 Compatible Devices 151209 A-15...
Page 222 IntelliKnight 5820XL Installation Manual A-16 151209...
Page 223: Appendix B Special Characters Lists
Appendix B Special Characters Lists This section contains tables of programmable characters that may be used for device, module, and zone names or phone numbers. Characters used for Naming Table B-1 list the available character and their associated numeric designator. When programming these numbers can be entered as a short cut to using the up or down arrow keys, to select characters when naming a point or zone.
Page 224 IntelliKnight 5820XL Installation Manual 151209...
Page 225: Silent Knight Fire Product Warranty And Return Policy
Repair and RA Procedure • All products that are returned to Silent Knight for credit or repair require a RA (Return Authorization) number. Call Silent Knight Customer Service at 800-446-6444 or 763-493- 6435 between 8:00 A.M. and 4:45 P.M. CST, Monday through Friday to obtain a return authorization number.
Page 226 A new or refurbished board will be shipped to the customer. The customer will initially be billed for the replacement board but a credit will be issued after the repairable board is received at Silent Knight. All returned products must comply with the guidelines described under “General Terms and Conditions”.
Page 227: Limited Warranty
This warranty is void if the product is altered or repaired by anyone other than SILENT KNIGHT or as expressly authorized by SILENT KNIGHT in writing, or is serviced by anyone other than SILENT KNIGHT or its authorized distributors.
Page 230 SILENT KNIGHT ® by Honeywell 7550 Meridian Circle, Ste 100 Maple Grove, MN 55369-4927 763-493-6455 or 800-328-0103 Fax: 763-493-6475 © 2007 Honeywell International Inc.

SILENT KNIGHT 5820XL Installation And Operation Manual

Section 1

Introduction

Section 2

Agency Listings, Approvals, and Requirements

Section 3

Before You Begin Installing

Section 4

Control Panel Installation

Section 5

SLC Device Installation

Section 6

Programming Overview

Section 7

Programming

Section 8

System Operation

Section 9

Reporting

Section 10

Testing and Troubleshooting

Section 11

Installation Records

Appendix A Compatible Devices

Appendix B Special Characters Lists

Silent Knight Fire Product Warranty and Return Policy

Quick Links

Troubleshooting

Need help?

Questions and answers

Related Manuals for SILENT KNIGHT 5820XL

Summary of Contents for SILENT KNIGHT 5820XL